Search
1986 articles for “In0.51Ga0.49P composite material” (ranking capped at the first 2,000 matches — narrow the search to see the rest)
Nothing matched all of your words, so these match any of them.
-
Impact Analysis of Different Active Layer (CH3NH3PbI3) Thickness Using Cu2O as Hole Transport Layer in Perovskite Solar Cell
Abstract: AbstractThickness of active Layer (CH3NH3PbI3) shows important role in term of stability and efficiency of perovskite solar cells. In this paper the numerical simulation and extensive modeling have been performed on perovskite solar cell using perovskite material such as methyl ammonium lead Iodide (MAPbI3, MA=CH3NH3) at different thickness with the help of SCAPS tool. The electrical properties of the MAPbI3 material used as active layer, have been calculated for different …
Published in Trends in Opto-electro & Optical Communication · Vol. 10, Issue 2, 2020 · pp. 15–20 Read article
-
Sensitivity of Rigid Pavement Responses to Pavement Layer Thickness Due to Wheel Load: A Nonlinear Finite Element Study
Abstract: The behavior of a jointed plain concrete pavement (JPCP) has been investigated under single wheel load for interior loading using finite element technique to predict the critical pavement responses for both linear and nonlinear geometrical characterization. The idealized pavement system is analyzed using 3D finite element analysis with the general purpose finite element software ABAQUS. The developed 3D model was analyzed for four combinations of material characterizations- (1) linear base …
Published in Trends in Transport Engineering and Applications · Vol. 1, Issue 1, 2014 · pp. 1–9 Read article
-
Comparative Evaluation of Shear Bond Strength of Three Different Generations of Adhesive to Dentin: An In Vitro Study
Abstract: The clinical use of resin composites has expanded considerably over the past few years due to increased esthetic demands by patients, new improved formulations, and simplification of bonding procedures. Novel resin composites benefits from improved filler technology and modifications of the organic matrix for a greater degree of polymerization .Improved marginal sealing around composites has reduced the frequency of unfavorable postoperative responses. The sealing ability of a composite restoration is …
Published in Research and Reviews: A Journal of Dentistry · Vol. 5, Issue 2, 2014 · pp. 9–17 Read article
-
Impressions in Fixed Partial Dentures: A Review
Abstract: Flawless impression is the most critical of simplicities in indirect restorative dentistry. Pre-requisite for successful fixed partial denture is an accurate three dimensional facsimile of the prepared teeth. Knowledge of various impression techniques, nature and behavioral properties of the available impression materials is mandatory for a good impression. Today the techniques and materials exceed our needs in terms of accuracy and properties. Yet, a flawed and imperfect impression is not …
Published in Research and Reviews: A Journal of Dentistry · Vol. 6, Issue 1, 2015 · pp. 23–32 Read article
-
Food Packaging Chemicals and Human Health: Molecular Toxicity, Exposure Pathways, and Regulatory Perspectives
Abstract: Food packaging plays a vital role in preserving food quality, extending shelf life, and ensuring safe transportation. However, increasing evidence indicates that chemicals from packaging materials can migrate into food during processing, storage, and consumption, resulting in chronic human exposure. Several food packaging chemicals, including bisphenols, phthalates, per- and polyfluoroalkyl substances (PFAS), styrene, heavy metals, and non-intentionally added substances (NIAS), have emerged as important xenobiotics due to their potential adverse …
Published in Research and Reviews: A Journal of Toxicology · Vol. 16, Issue 2, 2026 Read article
-
A Ventilated Dual-Function Photonic–Phononic Metasurface for Simultaneous Passive Radiative Cooling and Low-Frequency Noise Mitigation in Building Envelopes: Conceptual Design and Computational Feasibility Analysis
Abstract: Acoustic metamaterials for sound insulation and photonic/radiative-cooling metamaterials for passive thermal management have each matured separately for building-envelope retrofit, but existing studies address ventilation, acoustic damping and radiative thermal control in isolation, and no reported unit-cell architecture co-designs all three within a single shared structure. This gap persists because materials that are acoustic absorptive are generally dense and structurally opaque, whereas materials that are highly solar-reflective are conventionally applied to …
Published in International Journal of Energy and Thermal Applications · Vol. 4, Issue 2, 2026 Read article
-
Experimental Analysis and Optimization of Pulse TIG Welding Parameters for Dissimilar Aluminum Alloys
Abstract: Tungsten inert gas (TIG) welding is highly regarded as the primary welding method, especially for challenging metals like aluminum. Pulsed-current TIG welding has been specifically developed for welding aluminum alloys. Composite weld joints of aluminum alloys AA5052 and AA6063 find extensive use in diverse sectors such as automotive and marine applications, where significant mechanical properties and corrosion resistance are required. It is crucial to carefully select the process parameters to …
Published in Journal of Materials & Metallurgical Engineering · Vol. 16, Issue 2, 2026 · pp. 01–12 Read article
-
Structure and Crystal Growth of Urea Doped P- Block Element
Abstract: Nonlinear optical (NLO) materials exhibiting second harmonic generation have attracted considerable attention over the past few decades because of their technological significance in areas such as optical communication, signal processing, and instrumentation. Urea, being an important NLO material, presents challenges in crystal growth and handling due to its highly hygroscopic nature. Various derivatives of urea have been investigated for NLO applications, and some have shown promising potential in this field. …
Published in International Journal of Crystalline Materials · Vol. 3, Issue 2, 2026 · pp. 08–13 Read article
-
Effect of Particle Size of Sand on the Interface Shear Behavior of Sand and Non-woven Geotextile
Abstract: Soil-geosynthetic interface is the weakest zone for shear failure. It is influenced by size, shape, density and water content of sand. It is also influenced by the properties of geosynthetic such as texture and structure. This paper explores the influence of the size of sand on the behavior of sand-geotextile interface. Three types of sands namely coarse, medium and fine sand and non-woven geotextile were used in this study. Several …
Published in Journal of Geotechnical Engineering Read article
-
Mechanical Performance Degradation of Naturally Aged Nitrile Butadiene Rubber in Low Frequency Range...
Abstract: For good mechanical design, damping is often still an invisible requirement. Nitrile Butadiene Rubber (NBR) has a wide range of applications as a damping and sealing material. To offer the long-term service of NBR, it is important to estimate the degradation of modal properties under complex mechanical and environmental loading. The present work aims to correlate the experimental data with generalized higher-order Maxwell models and curve fitting techniques to find …
Published in Journal of Polymer & Composites Read article
-
Analytical Study of Concrete-encased Steel Column Building against Blast Load
Abstract: Study of behavior of composite building with Concrete-Encased Steel (CES) columns for blast loading is done. This is compared with the behavior of conventional building having reinforced concrete (RC) columns. In the following study, both composite and RC buildings are subjected to 0.1 ton, 0.3 ton and 0.5 ton TNT equivalent charge weight of blast load with a standoff distance of 20 m, 30 m and 40 m. To study …
Published in Journal of Structural Engineering and Management Read article
-
Design, Fabrication and Testing of Safety Valve Vent Silencer with Cyclone Separator for Industrial Applications
Abstract: The aim of this research work is to safeguard the infill materials, which is used inside the safety valve vent silencer. This research will help the infill materials from the wet steam and increases the life of the infill materials. The main parts of the research project are the cyclone chamber, center pipe. This cyclone separator drains the condensate through the lower part of the silencer and the steam releases …
Published in Journal of Industrial Safety Engineering Read article
-
The Theoretical and Experimental Study of the Behavior of the Mercury Drop, Fixed on the Glass Bottom of Vessel with Fluid, Under the Acceleration of Gravity Change
Abstract: At present time, accumulated theoretical material of the studies of the equilibrium forms of the gas bubbles or mercury drops, fixed on the surface of solid material in the fluid or on the glass bottom of vessel with fluid, under the acceleration of gravity change, was carried out either on the basis of geometric similarity laws that greatly simplify the essence of physical processes, or on the basis of theoretical …
Published in Recent Trends in Fluid Mechanics Read article
-
AQUASOMES: A Vesicular, Self-assembled Ceramic Nanoparticulate Drug Carrier
Abstract: Nano-biopharmaceutics involves delivery of biopharmaceutical product through different biomaterials like multi-functional nanoparticles, quantum dots, aquasomes, super-paramagnetic iron oxide crystals, and liposomes dendrimers. Aquasomes are considered as one of the most recently developed delivery systems for bioactive molecules like peptides, proteins, hormones, antigens and genes to specific sites. Aquasomes have a spherical shape and a particle size of 60–300 nm. These are three layered self-assembled nano-particulate carrier system. This three-layered structure …
Published in Research and Reviews: A Journal of Pharmaceutical Science · Vol. 12, Issue 3, 2025 · pp. 1–14 Read article
-
Numerical Studies on Deep Drawability of the Aluminium Alloy, AA6082 and Parameters Affecting It
Abstract: Deep drawing is a metal forming operation used for manufacturing sheet-metal components for application in the automobile, aerospace, and packaging industries. The objective of the present work was to study the various parameters influencing the drawability of AA6082. The deep-drawing process was modeled and simulated in Ls-Dyna Pre-Post(R) V4.6.17 software. The tensile test was performed according to the ASTM-E8M standard on AA6082-T6 material and subsequently annealed to attain higher ductility. …
Published in Journal of Polymer & Composites Read article
-
Experimental Analysis of Cutting Forces Under Different Machining Parameters and Carbide Inserts During Turning of Hardened AISI 4340 Steel
Abstract: Turning of hardened materials with an advanced coated carbide insert has numerous advantages over the grinding process, e.g., reduced process cost, high material removal rate, and less environmental concern due to the elimination of the cutting fluid. Process parameters in conventional machining operations like cutting speed, feed, and depth of cut play the most crucial role behind the generation of heat which also leads to microstructural changes, improved tool life, …
Published in Journal of Polymer & Composites Read article
-
Hybrid Supercapacitor Application for Future E-mobility
Abstract: With the rise in demand for automobiles, there is an increase in pollution levels and global warming since the past decade, there is a strong need for an alternative mode of commuting like Electric vehicles against conventional gasoline/diesel-powered vehicles to safeguard the planet and its flora and fauna. Battery technology like lithium-ion and others has already revolutionized the automotive world, but there is a limitation of fast charging, operating temperature …
Published in Journal of Polymer & Composites Read article
-
Synthesis, Properties, Nanocomposites, and Electrochemical Applications of Polyaniline: A Review
Abstract: Polyaniline, also known as PANI, is a polymer in the that is becoming more significant for academics in the field of nanotechnology due to the potential uses it has in sensor technologies, optoelectronics, and photonics. PANI can be rapidly doped by a broad range of acids and dopants due to the ease with which it may be manufactured and its exceptional resilience in the natural environment. In this article, we …
Published in Journal of Polymer & Composites · Vol. 11, Issue 3, 2023 · pp. 13–20 Read article
-
Topology Optimization of Press Tools for Additive Manufacturing: Reducing Manufacturing Time
Abstract: This research paper presents a topology optimization study of a press tool consisting of a punch and a die, with the aim of optimizing the press tool topology to reduce material usage, and manufacturing time while maintaining necessary strength. The tools will be manufactured using additive manufacturing technology with Polylactic Acid (PLA) material. The Additive Manufacturing method can be used to make prototypes of press tools in the development stages. …
Published in Journal of Polymer & Composites · Vol. 11, Issue 8, 2023 · pp. 40–56 Read article
-
A Critical Review on Semi-solid and Solid Lubricants for Industrial Applications
Abstract: Friction materials are very important for the safe moving of automobiles and the safety of people. As the pad slides against its match, the moving energy is turned into heat by the friction. As the vehicle's speed is lost as heat in the pads and rotors, the friction at the contact slows it down. Lubricants are compounds that are applied to moving parts to reduce friction and wear. Used primarily …
Published in Journal of Polymer & Composites · Vol. 11, Issue 8, 2023 · pp. 105–114 Read article