Search
73 articles for “frequency range”
-
Mechanical Performance Degradation of Naturally Aged Nitrile Butadiene Rubber in Low Frequency Range...
Abstract: For good mechanical design, damping is often still an invisible requirement. Nitrile Butadiene Rubber (NBR) has a wide range of applications as a damping and sealing material. To offer the long-term service of NBR, it is important to estimate the degradation of modal properties under complex mechanical and environmental loading. The present work aims to correlate the experimental data with generalized higher-order Maxwell models and curve fitting techniques to find …
Published in Journal of Polymer & Composites Read article
-
Comparison Analysis of Transformer Boosting and Induced Degeneration Topology Design of LNA for Millimeter Wave Frequency Range Using Polymeric Substrates
Abstract: In this study, a comparison between transformer boosting and source degeneration LNA topologies is conducted using two polymeric substrates—Polyimide (PI) and Liquid Crystal Polymer (LCP)—for millimeter-wave (mmWave) applications. With growing interest in flexible and high-frequency electronics, polymeric materials offer unique advantages such as low dielectric constants, mechanical flexibility, and thermal stability. The analysis explores gain, return loss, and noise figure performance while evaluating the influence of dielectric properties on the …
Published in International Journal of Electrical and Communication Engineering Technology · Vol. 3, Issue 2, 2025 · pp. 1–24 Read article
-
Dielectric Properties of Reduced Graphene Oxide with Nickel Cobalt Ferrite and Nickel Zinc Ferrite Epoxy Nanocomposites
Abstract: In this work, two systems of the composite were prepared using NiCoFe and NiZnFe with reduced graphene oxide(rGO) epoxy and the samples were subjected to electrochemical impedance spectroscopy (EIS). The Quality factor and loss tangent values of the composite was found out as a function of frequency. The modified ferrite-graphene-epoxy blends show dielectric loss and Quality factor values at low frequency. The incorporation of graphene aims to improve electrical conductivity, …
Published in Journal of Polymer & Composites · Vol. 11, Issue 11, 2023 · pp. 28–37 Read article
-
Alzheimer disorders diagnosis system design using machine learning for EEG signal
Abstract: The diagnosis of Alzheimer's disorders (AD), a prevalent neurological disorder, can created by utilising a range of therapeutic methods, including the electroencephalogram (EEG), which has been especially successful in the past. The objective for this study is to develop a computer-aided diagnosis tool which may recognize AD from EEG data. The EEG information was cleaned up with a band-pass elliptic digital filter to remove any interference or disruptions. The filtered …
Published in Journal of Control & Instrumentation Read article
-
High-Gain Microstrip Patch Antenna for Satellite and Radar Applications
Abstract: The growing demand for high-speed wireless communication, satellite connectivity, and advanced radar systems has increased the necessity for compact and high-performance antenna designs. This study presents the design and analysis of a high-gain microstrip patch antenna intended for satellite and radar applications operating in the microwave frequency range. The proposed antenna structure is developed using a low-loss dielectric substrate to enhance radiation efficiency, bandwidth, and gain characteristics while maintaining a …
Published in Journal of Microwave Engineering and Technologies · Vol. 13, Issue 2, 2026 Read article
-
Unraveling Mixed Ionic-Electronic Conduction in Lithium-Substituted Rubidium Tetra Titanates via Dielectric Spectroscopy and EPR Analysis
Abstract: Lithium-substituted Rubidium Tetra Titanates with varying concentrations of lithium carbonate (Li₂CO₃) — specifically 0.01, 0.05, and 0.1 molar percentages — were successfully synthesized using a conventional high-temperature solid-state reaction method. The resulting compounds follow the general chemical formula Rb₂₋ₓLiₓTi₄O₉. X-ray diffraction (XRD) analysis confirmed that lithium ions were successfully incorporated into the crystal lattice without disrupting the fundamental layered structure of the host material. The crystal system remained monoclinic across …
Published in Research & Reviews : Journal of Physics · Vol. 14, Issue 2, 2025 · pp. 19–29 Read article
-
Millimeter Wave in Internet of Things Connectivity: A Study
Abstract: The internet of things (IoT) is rapidly evolving, connecting billions of devices and transforming industries. However, this growth is stretching the limitations of traditional wireless communication technologies. Enter millimeter wave (mmWave), a high-frequency band promising to revolutionize IoT connectivity by offering significantly higher bandwidth and lower latency. While still in its early stages of implementation, mmWave is poised to become a cornerstone of the next generation of IoT ecosystems. Millimeter …
Published in International Journal of Wireless Security and Networks · Vol. 3, Issue 1, 2025 · pp. 13–23 Read article
-
Synthesis and Characterization of Forsterite Incorporated HDPE Composites for Microwave Substrate Application
Abstract: High Density Polyethylene (HDPE) combined with dispersed forsterite (Mg₂SiO₄) powder was utilized to fabricate polymer matrix composites (PMCs) aimed at high-frequency microwave substrate applications. Forsterite powders were synthesized using the mixed oxide method, and their phase purity was confirmed by X-ray diffraction (XRD) analysis. The dispersion and morphology of the ceramic filler within the HDPE matrix were examined through Scanning Electron Microscopy (SEM), ensuring a homogeneous distribution essential for optimal …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 109–120 Read article
-
Quad-Band Notched Small Monopole Antenna with U-shaped Slots and SRRs for UWB Applications
Abstract: A quad-band notched small monopole antenna with U-shaped slots and SRRs for UWB applications is presented in this study. The quadruple band-notched characteristics can be achieved by embedding three U-shaped slots on the radiation patch and two split ring resonators (SRRs) near feed line, respectively. It has a tiny size, only 17 mm23 mm0.508 mm. The experimental and measured results demonstrate that the proposed antenna offers an impedance bandwidth across …
Published in Journal of Communication Engineering & Systems · Vol. 15, Issue 1, 2025 · pp. 21–31 Read article
-
Current Controlled Oscillator Using FinFET
Abstract: A current-controlled oscillator using 18 nm FinFET technology is proposed in this study which consists of a Current Controlled Differential Difference Current Conveyor (CCDDCC) block to control the current. FinFET technology has better scalability and lower leakage current compared to traditional CMOS, which allows it to surpass the obstacles faced by CMOS-based oscillators. The suggested oscillator is suitable for electronic applications such as Phase-Locked Loop (PLL) systems, radio frequency (RF) …
Published in Journal of Semiconductor Devices and Circuits · Vol. 12, Issue 3, 2025 · pp. 17–28 Read article
-
Internet of Things Connectivity Using Millimetre Wave: A Study
Abstract: Internet of Things(IoT) is undergoing rapid development, which is connecting millions of devices and causing sectors to undergo transformation. On the other hand, given this increase, the constraints of conventional wireless communication technologies are being stretched to their limits. Millimetre wave, often known as mmWave, is a high-frequency band that has the potential to revolutionise Internet of Things connectivity by providing much higher capacity levels and lower latency levels. Microwave …
Published in Journal of Microwave Engineering and Technologies · Vol. 12, Issue 2, 2025 · pp. 18–30 Read article
-
Experimental Analysis of Nano-carbon Doped Alumina for Industrial Applications
Abstract: The use of nano-carbon metal matrix composites can provide a solution to the enduring issue of optimal material selection and optimization for getting metal-insulator transition (MIT) behavior at a particular frequency at ambient temperature. Other substances, like two-dimensional (2D) transition metal dichalcogenides (TMD), vanadium oxide (VO2), and germanium telluride (Ge-Te), have difficult challenges in achieving effectively the MIT property at a given frequency and temperature. It is also difficult to …
Published in Journal of Polymer & Composites Read article
-
Electromagnetic Field Effects on Biological Systems and Safety Evaluation of Microwave Exposure
Abstract: The increasing use of wireless communication systems, radar technologies, and microwave- based devices has raised growing concerns regarding the potential biological effects of electromagnetic fields (EMFs) on living systems. This review paper investigates the interaction between electromagnetic field exposure, particularly in the microwave frequency range, and biological tissues, with a focus on safety implications and risk assessment. Microwave radiation, commonly emitted from mobile phones, Wi-Fi routers, and industrial equipment, can …
Published in Journal of Microwave Engineering and Technologies · Vol. 13, Issue 1, 2026 · pp. 26–33 Read article
-
A Comparative Analysis of Graphene Based Terahertz Reconfigurable Antennas: A Review
Abstract: In this paper, an overview of various reconfigurable antenna designs based on graphene material utilized for terahertz applications is presented. Terahertz electromagnetic spectrum is the term used to describe the frequency range between 0.1 and 10 THz. A promising material for THz reconfigurable antennas, graphene has a low skin effect and a built-in ability to tune by chemical or electrostatic gating. This study reviews the development of reconfigurable antenna for …
Published in Journal of Polymer & Composites · Vol. 11, Issue 5, 2023 · pp. 44–55 Read article
-
Thermal Stability and Sound Absorption Behaviour of Sisal–Luffa Hybrid Epoxy Composites for Automotive Interior Applications
Abstract: Natural fiber–reinforced composites are gaining popularity as substitutes for synthetic fiber composites because of their environmental and sustainability advantages. Their adoption is steadily increasing across various industries. In automotive interior applications, these materials must exhibit strong thermal stability and efficient sound absorption to meet performance requirements. In this experiment, composites were made by mixing sisal and luffa fibers with epoxy resin. The hand lay-up method was used for fabrication. Two …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 144–157 Read article
-
High Frequency Design Approach and Feasibility Study of HBT Based W-band (90.0 GHz-100.0 GHz) Amplifier using 130 nm SiGe Based BiCMOS Technology
Abstract: This paper present high frequency design approach and feasibility study of HBT (Hetero Junction Bipolar Transistor) based two-stage cascode amplifiers at W-band (90.0 GHz-100.0 GHz). The proposed amplifier has design using 130 nm SiGe based BiCMOS technology. This paper used low cost technology for designing of w-band amplifier and this is novelty of this paper. The schematic design and feasibility study has been carried out using Cadence software. The selection …
Published in International Journal of Digital Communication and Analog Signals Read article
-
Performance Enhancement of Microstrip Patch Antenna Using Metasurface
Abstract: Performance enhancement of microstrip patch antenna using metasurface provides a thorough analysis of how a metasurface integration technique might improve the performance of a microstrip patch antenna. The 4×4 array of square components metasurface measuring 51.6 × 51.6 × 3.1016 mm is merged with the microstrip patch antenna, which has dimensions A=13.5 mm, B=12 mm, and C=1.2 mm. The radiation box dimensions (100 mm × 100 mm × 55 mm), …
Published in Journal of Microwave Engineering and Technologies · Vol. 11, Issue 3, 2024 · pp. 20–27 Read article
-
Investigation of Dielectric Properties of Lead-Free BaTiO3 Ceramic at Different Sintering Temperatures
Abstract: In the present study, Barium titanate (BaTiO3) was produced using the conventional solid-state sintering technique at three distinct sintering temperatures: 1000, 1100, and 1200°C. It was confirmed by the X-ray diffraction pattern that the perovskite phase was formed without secondary peaks and that the presence of the tetragonal phase was observed near room temperature. Upon conducting a frequency- dependent dielectric study, it was found that ceramic sintered at 1100°C exhibited …
Published in Recent Trends in Fluid Mechanics · Vol. 12, Issue 1, 2025 · pp. 23–30 Read article
-
Performance Evaluation of Hybrid Polymer Composite Materials for Electromagnetic Interference Shielding in Flexible and Wearable Electronic Devices
Abstract: Wearable electronic devices require novel hybrid polymer composites that offer flexible, lightweight and highly effective EMI shielding characteristics. The development and characterization of flexible polymer composites combining hard magnetic nanoparticles and electrically conductive fillers are explored. The suitability of thermoplastic polyurethane (TPU), polydimethylsiloxane (PDMS) and epoxy resins for use as EMI shielding composite matrices was evaluated in terms of their flexibility, stability and biocompatibility. Hybrid filler systems were developed to …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 630–648 Read article
-
Accuracy Improvement for Propeller Cavitation Noise Prediction Using UDF
Abstract: Recently, there has been an increase in demand for propulsion systems with higher hydrodynamic performance and lower underwater-radiated noise, as environmental issues are gaining more attention in addition to the traditional military necessity. It is important to reduce cavitation noise when designing propellers of the ships, especially for oceanographic research vessels because they use acoustic instruments and cavitation noise can interfere with their operation. It is well known that, when …
Published in Journal of Experimental & Applied Mechanics · Vol. 16, Issue 2, 2025 · pp. 18–26 Read article