Search
98 articles for “Pores”
-
Pore-structural Parameters of Concrete, their Inter-Relationship and Correlation to Compressive Strength
Abstract: An extensive literature review was carried out on various forms of pore structural parameters (pore diameters) of concrete such as critical pore diameter, mean pore diameter, and threshold pore diameter and their correlations to compressive strength of concrete. From the review of the literature, it has been observed that the inter-relationships among various forms of pore diameters and their correlation to compressive strength of concrete have not been discussed much …
Published in Recent Trends in Civil Engineering & Technology · Vol. 2, Issue 1-3, 2012 · pp. 102–112 Read article
-
Pore Distributions in Porous Anodic Aluminum Oxide (PAAO) Surfaces of Pure and Commercial Aluminum Substrates
Abstract: Porous anodic aluminum oxide (PAAO) surfaces were developed on pure aluminum (PA) and commercial aluminum (CA) substrates by anodization as a function of voltage in phosphoric acid bath at 278 K and were analyzed by scanning electron microscopy. The interpore distances were plotted in the form of frequency histograms to examine pore-ordering characteristics. Self-ordered porous structures have been obtained at 200 and 160 V for PA and CA substrates respectively …
Published in Journal of Materials & Metallurgical Engineering · Vol. 2, Issue 1-3, 2012 · pp. 143–153 Read article
-
Impact of water-cement ratio and cement content on pore area percentage and chloride diffusion – A molecular dynamics study
Abstract: The exposure of a reinforced structure to water-based settings leads to the occurrence of chloride-induced corrosion, resulting in a reduction in both the durability and performance of the structure. The entry of chloride ions into concrete and the pore area percentage is influenced by several elements, including the degree of humidity, the presence of fractures, environmental conditions, water-to-cement ratio (w/c ratio), and cement content. This research focuses on the utilization …
Published in Journal of Construction Engineering, Technology & Management · Vol. 13, Issue 3, 2023 · pp. 37–45 Read article
-
In Situ Determination of Surface Porosity and Pore Characterization in Refractories
Abstract: Surface pore characterization and surface porosity determination of test refractories produced to varying porosities were done using image analysis. The surface pore count, pore size and pore area distributions were presented in a surface porosity chart that is characteristic of the surface. Instant visual information from these chart were noted. The sharp beak pattern, for instance, is notable as a chart signature characteristic of a dent or rupture on the …
Published in Journal of Materials & Metallurgical Engineering · Vol. 3, Issue 3, 2013 · pp. 14–22 Read article
-
Green Synthesis of Biologically Active 2, 4, 5- Trisubstituted Imidazoles Catalyzed by Large Pore Zeolite H-BEA through Lophine MCRs
Abstract: 2, 4, 5-triphenyl-1(H)-imidazoles (popularly known as Lophine derivatives) are well known heterocyclic compounds and find significant diversified applications, not only in the area of medicinal chemistry as biologically active drug-like molecules, but also in the other advanced research areas, such as fluorescence labelling, biological imaging and chromospheres for non-linear optic system. In the present endeavour, a green synthesis of Lophine derivatives via multi-component reaction is carried out using benzil/benzoin, substituted …
Published in Journal of Catalyst & Catalysis · Vol. 4, Issue 3, 2017 · pp. 20–36 Read article
-
Effect of Surface Pore Filling and Adhesive Joining on Energy Absorption of Closed Cell Aluminum Foam
Abstract: The joining of aluminum foam is explored in this paper. Foam specimens were sectioned and joined with commercially available adhesive and tested for its energy absorption capability against a normal foam specimen. There was a decrease in the plateau stress but the decrease is not significant. The effect of surface pore filling by the adhesive was also realized. It was found that the adhesive in the surface cells introduces constraints …
Published in Journal of Materials & Metallurgical Engineering · Vol. 2, Issue 1-3, 2012 · pp. 117–124 Read article
-
Study of Ablation Characteristics Carbon Fiber Reinforced Plastic with Silicon Carbide Pores
Abstract: Significant thermal stress is placed on spacecraft during atmospheric re-entry, primarily due to aerodynamic heating. This intense heat can cause severe material damage threatening the spacecraft's structural integrity. To address this challenge, efforts are focused on improving the ablation resistence of spacecraft components. In this work, carbon fiber reinforced plastic (CFRP) composites containing silicon carbide (SiC) holes are explored as a potential solution for enhancing thermal protection system. Four different …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 617–627 Read article
-
Stress Distribution below Strip Footing Using Finite Element Analysis
Abstract: The estimation of stress distribution below ground is important in all types of geotechnical analysis. That is why the correctly measured value of stress distribution below ground level under various conditions will be helpful for resilient design in geotechnical point of view. This paper presents an analysis of vertical stress distribution below a strip footing due to varying applied loads using finite element method (FEM) modeling in ABAQUS and the …
Published in Journal of Geotechnical Engineering · Vol. 3, Issue 3, 2016 · pp. 16–22 Read article
-
Comparative Analysis of Pond Ash as a Partial Replacement of Sand as Subbase Material for Concrete Paver Block Hardstand sustaining storage of Bulk Cargo
Abstract: This work presents an industrial waste-derived subbase material that can take the place of conventional granular material for subbase in hardstand foundation construction. This industrial waste hugely deposited in the ash lagoons namely Pond Ash (PA) which is globally generated at an amount of 780 Metric Tons from thermal power plants annually ,as foundation material for hardstand construction, will not only help the cause of residual waste disposal problems but …
Published in Journal of Geotechnical Engineering · Vol. 12, Issue 3, 2025 · pp. 32–45 Read article
-
TQM Need and Application in the Billing Process
Abstract: This study investigates need for improvement in quality management by billing department, in the companies already certified for ISO and implementing measurement and reporting of cost of quality in the billing department. Its main purpose is to examine the gaps in the billing procedure that needs to close behind quality certification and the extent to which a firm can measure and report quality costs. A sample of 360 bills was …
Published in Journal of Construction Engineering, Technology & Management · Vol. 2, Issue 1-3, 2012 · pp. 87–101 Read article
-
A Study on adsorption of Phenol red dye and Chromium (VI) metal ion using activated carbon derived from Lantana camara with the activation of potassium hydroxide.
Abstract: Commercial activated carbons are expensive to produce and regenerate, it is essential to produce activatedcarbon using low-cost raw materials and methods. This study's goal is to demonstrate the possible adsorptionproperties of activated carbon made from Lantana camara for the removal of dyes and metal ions fromaqueous solutions. In this study, activated carbon from Lantana camara stems was obtained through a one-step chemical activation procedure using potassium hydroxide KOH. The surface …
Published in Journal of Nuclear Engineering & Technology · Vol. 13, Issue 1, 2023 · pp. 1–10 Read article
-
A New Description of Multi-phase Flow Behavior at Boundary Layers of Low-permeability Porous Media
Abstract: At present, the recovery factor of low permeability oilfield in China is only about 20%, which is enormously lower than the recovery factor index of 60% by using water-chemical flooding in medium and high permeability layer. There are a lot of causes that resulted in low recovery factor, among them that the complex pore structure, tiny throat, large pore throat ratio and non-Darcy flow in low-permeability oil layer are the …
Published in Journal of Petroleum Engineering & Technology · Vol. 3, Issue 1, 2013 · pp. 1–7 Read article
-
5000 Series of Aluminum and Its Alloys Opaque by Inhibitors
Abstract: 5XXX series of alloys are prepared for marine applications. Light weight, strength, low maintenance and inherent tendency to form passivity surfacing have selected these alloys for manufacture of cargo ships. Anti corrosive paints have been traditional protections in these alloys. Workers exposed to chromate residues during sanding of aircraft and recoating have increased risk of cancer to 250,000-fold higher. These paints are hazardous for aquatic life, so eco-friendly corrosion inhibitors …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 6, Issue 2, 2019 · pp. 1–8 Read article
-
Valorization of Human and Cattle Dental Waste into Functional Composite Biomaterials: A Detailed Comparative Analysis
Abstract: This study investigates the conversion of human and cattle (goat and cow) teeth into bioactive hydroxyapatite-based composites and presents a detailed comparative evaluation of these biogenic materials with laboratory-synthesised (synthetic) hydroxyapatite (HAp). In this work, hydroxyapatite was extracted from human and bovine teeth through controlled calcination and milling, while synthetic HAp was prepared using a standard wet chemical precipitation route. All materials were subsequently sintered at 900 °C and fabricated …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 340–354 Read article
-
Performance Evaluation of H 2 SO 4 -Rice Husk-Moss Adsorbent for the Removal of Zn (II) Ion from the Effluent of Science Equipment Development Institute (SEDI)
Abstract: This research was carried out to investigate the potential of green algae (moss) with the support of H 2 SO 4 treated rice husk activated carbon using batch adsorption process for the removal of Zn (II) ions from SEDI industrial effluent. The rice husk- moss algae was activated using H 2 SO 4 . The effluent was characterized using atomic absorption spectrophotometer with initial concentration values of 12.3 mg/l for …
Published in Journal of Catalyst & Catalysis · Vol. 9, Issue 1, 2022 · pp. 6–15 Read article
-
Investigate an Implementation Study of TI-6AL-4V Lattice-based Scaffold Design Using Finite Element Analysis
Abstract: Implementation studies are advised to determine the effectiveness and performance of bone scaffolding in morphology, which has been demonstrated scientifically. The rehabilitation of bone defects, which is still a complex problem in orthopedic surgery, was the subject of an implementation study we provided. Biomaterial scaffolding porosity and pore size are essential in both in vivo and in vitro bone development. However, it has been linked to various drawbacks, including poor …
Published in International Journal of Biochemistry and Biomolecule Research · Vol. 1, Issue 1, 2023 · pp. 28–35 Read article
-
A non-hydrotreated feedstock’s polyaromatic cracking under FCC industrial operating conditions using an equilibrium catalyst
Abstract: Catalytic cracking of non-hydrotreated atmospheric residue’s main polyaromatic hydrocarbon (PAHs) in the presence of an equilibrium catalyst was investigated under industrial operating conditions. During the fluid catalytic cracking process, the catalyst that presented the key factor in hydrocarbon cracking (aromatic by hydrogen transfer reaction) quickly deactivated and compromised the process’s performance due to its acid surfaces and pores covered by the polyaromatic species. A deep study of the catalyst behavior …
Published in Journal of Catalyst & Catalysis · Vol. 12, Issue 1, 2025 · pp. 10–26 Read article
-
Au@Sio2@PVP-DCMD Membranes: A Breakthrough in Heavy Metal Removal and Antibacterial Defense
Abstract: This study investigates the development and characterization of multifunctional gold-doped silica (Au@SiO₂) membranes for water distillation and antibacterial applications. The manufacturing process integrated gold nanoparticles into silica matrices using sol-gel techniques. Structural analysis was conducted using SEM (showing uniform pore distribution with an average pore size of 40-50 nm), FTIR (confirming Si-O-Si and Si-Au-Si bonding peaks at 525 cm⁻¹ and 1310 cm⁻¹ respectively), EDX (revealing gold nanoparticle content of 1.5 …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 13–27 Read article
-
Finite Element Formulation for Mechanical Buckling of FGM Plate Exposed to Various Boundary Conditions
Abstract: Mechanical buckling analysis of functionally graded (FG) material plates based on first-order shear deformation theory. In the real world many components manufactured by FG materials face the buckling load under certain conditions. Various types of gradation law for tailoring the material properties are applied by the researcher, out of that, presently a simple power law for material gradation is applied with shear correction factor (SCF) is used to take account …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 503–513 Read article
-
Generative Design of Bioactive Orthopedic Composites for Fracture Repair Using an Integrated Conditional GAN–Transformer Framework: A Multi-Objective Approach
Abstract: Orthopedic composite implants for fracture repair must simultaneously satisfy conflicting mechanical and biological demands: high fracture toughness, sufficient compressive stiffness, and bioactive surface chemistry enabling osteoblast adhesion and mineralization. Existing design approaches rely on trial-and-error experimentation, yielding sub-optimal trade-offs between these objectives. This paper presents an integrated conditional Generative Adversarial Network–Transformer (cGAN-T) framework for fully computational, multi-objective generative design of hydroxyapatite (HA)-reinforced polymer composite microstructures targeting Orthopedic fracture repair. A …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 · pp. 21–35 Read article