Journal of Polymer & Composites
Volume 13, Issue 2 (2025)
Table of contents
-
Investigation of Process Specifications on Friction Stir Welded Aluminium 5083 and 6082 Alloys
Abstract: Aluminium 5083 alloys were mainly used for naval based applications because of better corrosion resistance feature. Similarly aluminium 6082 alloy being a structurally significant material found its applications in construction sector. Fusion welding of these two heterogeneous alloys is bit hard, since it evolves many defects. Present Investigation deals with two cases of distinct alloys through FSW process. Case 1 represents 31 experimental trails performed by 5 various tool pin …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 1–11 Read article
-
Effect of Thermal Conditioning - Mechanical Performance of Natural-Synthetic Fiber Hybrid Composites
Abstract: This study investigates the effects of thermal conditioning on the mechanical and thermal properties of banana-glass fibre hybrid composites, focusing on their tensile, flexural, impact strength, and thermal conductivity. Hybrid composites were fabricated with varying banana-to-glass fibre ratios of 70:30, 50:50, and 30:70 using a hand layup technique, followed by thermal conditioning at 60°C, 80°C, and 100°C for a specified duration. Results highlight that the 50:50 composite treated at 80°C …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 1–11 Read article
-
Characterization of Nano-Clay Reinforced Polymer Composites: Enhancing Performance for Extreme Applications
Abstract: This study investigates the mechanical, thermal, water absorption, and chemical resistance properties of nano-clay-reinforced polymer composites and polymer concrete. The incorporation of 1-5 wt% nano-clay resulted in a significant enhancement across all properties. Mechanical testing revealed a 42.86% increase in tensile strength (35 MPa to 50 MPa), 40% improvement in flexural strength (50 MPa to 70 MPa), and 46.67% rise in compressive strength (75 MPa to 110 MPa), attributed to …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 105–114 Read article
-
Synthesis and Characterization of Forsterite Incorporated HDPE Composites for Microwave Substrate Application
Abstract: High Density Polyethylene (HDPE) combined with dispersed forsterite (Mg₂SiO₄) powder was utilized to fabricate polymer matrix composites (PMCs) aimed at high-frequency microwave substrate applications. Forsterite powders were synthesized using the mixed oxide method, and their phase purity was confirmed by X-ray diffraction (XRD) analysis. The dispersion and morphology of the ceramic filler within the HDPE matrix were examined through Scanning Electron Microscopy (SEM), ensuring a homogeneous distribution essential for optimal …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 109–120 Read article
-
Mechanical and Physicochemical Characteristics of Nano-Hydroxyapatite Polymer Composites
Abstract: This study focuses on the development and characterization of nano-hydroxyapatite (nHAp)-reinforced poly (lactic acid) (PLA) composites for biomedical applications. The composites, prepared with varying nHAp content (5–25 wt%), were evaluated for their mechanical and physicochemical properties, including tensile strength, Young’s modulus, elongation at break, thermal stability, hydrophilicity, and crystallinity. Results revealed that tensile strength increased significantly with the incorporation of nHAp, reaching a peak of 62 MPa at 15 wt%, …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 115–125 Read article
-
Exploring The Performance Dynamics of Basalt Fibre Reinforced Polymers: Mechanical and Viscoelastic Insights
Abstract: Basalt fibre reinforced polymer (BFRP) composites are gaining significant attention as sustainable alternatives to traditional reinforcement materials due to their superior mechanical performance, thermal stability, and eco-friendliness. This study examines the tensile, flexural, impact, and viscoelastic properties of BFRP composites fabricated via vacuum-assisted resin transfer molding (VARTM) using varying fibre volume fractions (20%, 30%, and 40%) and fibre orientations (unidirectional and bidirectional). The results reveal that composites with 40% fibre …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 12–22 Read article
-
Dielectric Studies of 0.5Ba0.8Ca0.2TiO3.0.5CaCu3Ti4O12 Nanoceramic Fabricated by Chemo-mechanical Process
Abstract: The present investigation is aimed toward investigate a straightforward, inexpensive, and environmentally friendly chemo-mechanical method for preparing high-dielectric materials, specifically 0.5Ba0.8Ca0.2TiO3.0.5CaCu3Ti4O12 (BCT-CCTO), by combining metal nitrate combustion with solid TiO2 powder and titanium isopropoxide, Ti (OR)4. The composite was prepared by the mixing of individual materials of Ba0.8Ca0.2TiO3 and CaCu3Ti4O12 through the chemo-mechanical method. Initially, 99% pure Ba (NO3)3, Cu (NO3)2∙3H2O, TiO2 and glycine were taken in their stoichiometry ratios. …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 12–21 Read article
-
Enhancing Concrete Performance With GGBFS: An Analysis of Strength Characteristics at Various Replacement Levels
Abstract: This study investigates the effect of ground-granulated blast furnace slag (GGBFS) as a partial replacement for cement on the mechanical properties of concrete. The primary objective was to assess the compressive, flexural, and split tensile strengths, along with the modulus of elasticity, at different replacement levels of cement with GGBFS and at distinct curing ages of 7, 28, and 56 days. Concrete mixes were prepared by replacing cement with GGBFS …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 121–138 Read article
-
Comparison of 11-Atom Armchair Graphene Nanoribbons and Zig-Zag Carbon Nanotubes in Polymer Composites Under Various Bias Voltages: A Study of Electronic and Transmission Properties
Abstract: In this research, 11-atom zig-zag carbon nanotubes (ZCNTs) and 11-atom armchair graphene nanoribbons (AGNRs) were studied under applied bias voltages at 50, 150, and 300 millivolt levels. The focus was on understanding their behaviour concerning transmission qualities, current-voltage (I-V) characteristics, and energy-momentum (E-K) diagrams. The Non-Equilibrium Green's Function (NEGF) approach was employed to analyse various electronic properties for ZCNTs and AGNRs, including transmission, E-K relationships, and I-V characteristics. The results …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 126–134 Read article
-
Current-Voltage Characteristics of 15-Atom Agnrs and Zcnts at Various Bias Voltages: Insights for Polymer Nanocomposite Applications
Abstract: The present research investigates the electronic properties of 15-atom Armchair Graphene Nanoribbons (AGNRs) and 15-atom Zig-Zag Carbon Nanotubes (ZCNTs) under applied bias voltages of 100, 200, 300, 400, 500, and 600 millivolts. Using the Non-Equilibrium Green's Function (NEGF) technique, the study analyzes various electrical features, including current-voltage (I-V) characteristics, to understand the behavior of these nanostructures. The findings reveal that AGNRs exhibit a larger bandgap than ZCNTs, which have a …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 135–144 Read article
-
Enhancing Performance of Hybrid Natural Fiber Reinforced Polymer: Insights into Processing, Characterization and Machining
Abstract: Natural fibre reinforced polymer composites (N-FRP) have gained popularity in recent years as an alternative to regular polymer composites, owing to growing environmental concerns. Natural fibers are becoming increasingly popular due to their outstanding properties such as flexibility, strength, compatibility with living creatures, and impact resistance. A notable application of natural fibers is in the medical industry, with the goal of producing cost-effective, sustainable, and long-lasting products. Combining different fibers …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 139–153 Read article
-
Mechanical Properties, Viscoelastic and Water Absorption Properties of Biocarbon-Reinforced Composites
Abstract: Biocarbon-reinforced polymer composites have emerged as a sustainable alternative to conventional composites, combining environmental benefits with promising material properties. This study explores the effect of varying biocarbon content (0%, 10%, 20%, and 30% by weight) on the mechanical, viscoelastic, and water absorption properties of a polypropylene (PP) matrix. Tensile strength tests reveal that incorporating 10% biocarbon yields the highest strength at 35 MPa, attributed to enhanced interfacial bonding. However, at …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 145–157 Read article
-
Affect of Finite Element Modelling on Static Behavior of Underwater Shell
Abstract: The objective of the present study is to compare and contrast different numerical models based on their mesh quality and material properties in predicting the response of an underwater shell under an external pressure of 1 MPa. Two different mesh qualities with the same element size are developed for solid geometries without and with slicing the solids at geometric discontinuities to enhance the element quality. From the static response of …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 154–163 Read article
-
An Overview of Composite Materials: Historical Development, Classification, and Advancements in Natural Fiber-Reinforced Polymer Composites
Abstract: Composite materials have brought about a paradigm shift in numerous industries by integrating distinct components to improve material performance. Consisting of a matrix and reinforcement, composites synergistically combine the unique properties of each constituent to deliver superior strength, enhanced durability, and remarkable flexibility. These attributes have made composite materials indispensable in diverse fields such as automotive, aerospace, construction, and marine engineering. This article provides a comprehensive exploration of the historical …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 158–175 Read article
-
Numerical Investigation on Concrete Filled Steel Tube Composite Circular Columns Under General Loading
Abstract: Concrete-filled steel tube (CFST) composite columns are extensively utilized in civil engineering constructions because of their numerous structural advantages, such as superior seismic performance, high load- bearing capacity, fire resistance, remarkable ductility, and ability to absorb energy effectively, especially in areas prone to seismic activity. CFST columns are employed in tall buildings and bridges to enhance rigidity and increase bearing capacity, but their behavior can be affected by buckling. There …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 164–199 Read article
-
Study of the CuS/CdSe Quantum Dots on the Optical Properties of Green Synthesis
Abstract: Chalcogenides based nanomaterials, such as CdSe are emerging as an important material offering transformative potential across multiple domains, such as photocatalysis, optoelectronics, sensing, and photo luminesce. In this study we synthesised CuS/CdSe quantum dots by varying CuS concentration through plant mediated green method. The copper sulfide synthesized at varying concentrations of the Se source, exhibited bonding configuration that are comparable to those of the Cd source. The goal of this …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 176–184 Read article
-
Green Synthesis and Evaluation of Electronic and Optical Properties of CdS/CdTe Quantum Dots
Abstract: The CdS/CdTe quantum dots (QDs), with altered concentrations of CdS, were synthesized using straightforward precursors through an environmentally friendly green method. The synthesized quantum dots were characterization by UV–visible absorption spectroscopy, Photoluminescence (PL), and Fourier Transform Infrared Spectroscopy (FTIR) to understand their electronic and structural properties. The average particle size is nearly consistent with the values derived from Brus's formula. The UV–visible spectra show a blueshift compared with pure sample, …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 185–194 Read article
-
Finite Element Analysis of Multiwall Carbon Nanotubes Enabled Single Lap Joint
Abstract: This study uses finite element analysis (FEA) to examine the strength of adhesively bonded single lap joints with and without Multiwall Carbon Nanotubes (MWCNT) added to the adhesive. Shear strength analysis is performed by applying a tensile load that generates shear stress at the overlap between the two substrates bonded with adhesive. Aluminum (Al-Al) substrates were used, and single-lap joints were prepared following ASTM standards. Specimens with identical overlap and …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 195–203 Read article
-
Influence of Nanomaterial on Biofuel Extracted from Lemon Seed Feedstock
Abstract: Biodiesel, which is a type of biofuel, offers a replacement to the traditional diesel fuel currently available on the market, which is derived from petroleum that is both more sustainable for the environment and more attractive from an economic standpoint. A plethora of environmental benefits can be obtained through the utilization of this technology, including a reduction in emissions of greenhouse gases and particulate matter, as well as the possibility …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 200–210 Read article
-
Optimization Of Mechanical Properties Of 500/7 Grade Ductile Cast Iron (DCI) By Using SMAW: Applications In Reinforced Composites And Thermoplastics Through Taguchi & GRA
Abstract: Welding, a critical manufacturing process, is broadly engaged to join metals and thermoplastics using heat, pressure, or both. This study inspects the Shielded Metal Arc Welding (SMAW) method to optimize welding parameters and improve the mechanical properties of Ductile Cast Iron (DCI) grade 500/7, a material widely used in high-strength and thermal conductivity applications in aerospace and automotive sectors. Using an L9 OA (orthogonal array), experiments were conducted on nine …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 204–222 Read article
-
Modeling of ZnO Based Nano Sensor Device for Evaluating Electronic Interaction with NO2 Pollutant: Combining Multiphysics Simulation and DFT Study
Abstract: This study focuses on the designing and modeling of a sensor device employing zinc oxide (ZnO) nanowires (NWs), and the evaluation of the chemical response of the same in the presence of nitrogen dioxide (NO2), which is an acute harmful pollutant for human health and environment. Experimentally synthesized ZnO nanostructures were used as the basis for modeling of the ZnO NWs based sensor device along with a single ZnO NW, …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 211–219 Read article
-
Use of Composite Materials for Sustainability
Abstract: Composite materials have emerged as key components in the quest for sustainability, providing a means to decrease environmental impact while improving performance in several applications. Some of the major benefits of using composites are durability, cut down regular repairs and replacements, preserve natural resources, reduce waste generation, and carbon footprint related to manufacturing processes. Due to renewability of natural fibers, the use of composites boosts sustainability and minimizes the environmental …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 22–34 Read article
-
Investigating The Synergistic Effects of Micro and Nano Particle Reinforcements in Powder Metallurgy-Processed Aluminum Metal Matrix Composites for Enhanced Mechanical Performance
Abstract: The ever-growing demands of modern mechanical applications necessitate the development of materials with superior mechanical properties. In this research, we delve into the creation and evaluation of Aluminum Metal Matrix Composites (Al MMCs) made via the powder metallurgy route, reinforced with both micro and Nano-scale particles. The key aim is to investigate the possible cooperative effects of this dual reinforcement approach on the mechanical behavior of the composite. Traditional aluminum …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 220–229 Read article
-
Comparison of High and Low Temperature Properties of Dual Modified Asphalt Binders with Polyphosphoric Acid and Polymer Modified Bitumen using Rheological Tests
Abstract: The main objective of this study was to investigate the properties of asphalt binder mixtures at both high and low temperatures. To achieve this, two types of admixtures were selected and combined, resulting in a technology known as dual modified asphalt binders. Extreme temperatures during summer and winter can lead to significant issues such as cracking and rutting in asphalt binder pavement. In order to address these problems, a comprehensive …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 23–34 Read article
-
Material Characterization Analysis of Fiber Reinforced Composites
Abstract: The study investigates the physical characteristics of PAN carbon fabric/epoxy composite which is a material commonly utilized in aerospace, defense, and automotive sectors. The material has exceptional mechanical properties like high specific strength and hardness. The materials utilized in this experiment are T-300 PAN carbon fabric, LY556 Epoxy resin, and HY5200 hardener to create pre-preg materials. Then the laminate was pre- pregged in a die mold of identical shape matched, …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 230–243 Read article
-
Mechanical Property Assessment of Hybrid Fiber Reinforced Composites Through Experimental Research
Abstract: Natural fibre reinforced composites are gradually taking the place of synthetic fibre composites due to its inexpensive cost, low density, and ease of supply. Furthermore, the addition of some waste materials to composites has remarkable properties that are attracting interest from a wide range of technical domains. Fibre reinforced with glass, carbon, and jute were used to generate hybrid composites. As a filler, different amounts of eggshell powder were mixed …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 244–251 Read article
-
Formation and Fabrication of A 3D- Printed Polymer Propeller for Improved Propulsion and Minimal Acoustic Emission: A Comparative Study for Small Unmanned Vehicles
Abstract: The current research focuses on a comparative analysis of propeller designs to identify an option that enhances thrust efficiency while minimizing acoustic noise. The study evaluates three distinct types of propellers: the traditional three-blade propeller, the Sharrow propeller, and a novel aero propeller featuring an air foil-shaped cross-section. To facilitate a hands-on analysis, these propellers were produced using 3D printing technology, specifically employing ABS filament through a Fused Deposition Modelling …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 252–261 Read article
-
Performance of GFRP Bars in Flexural Members: A Comparative Study with Metal Bars Using FEA and Experimental Study
Abstract: In recent years, GFRP bars have been introduced as a replacement for metal bars as reinforcement in flexural members. This study evaluates the use of GFRP bars as the main reinforcement in flexural members such as beams through computer simulations and experimental work. A 4-meter beam from a sample structure, analyzed as per IS 875 (1987) Part 2, was considered for the study. This beam was designed considering both metal …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 262–267 Read article
-
Numerical Study of Natural Convection Heat Transfer in Porous Particles Through Composite Filters
Abstract: The study of heat transmission through porous materials within the confines of reactor configurations stands as a pivotal realm of inquiry in the realms of engineering and the applied sciences, possessing wide-ranging applications spanning from soil mechanics to the refinement of heat exchange systems. Porous substances, distinguished by their interconnected voids or interstices, present an array of reactor forms that profoundly shape the flow of fluids and the conveyance of …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 268–279 Read article
-
Investigation of Mechanical Behaviour in Brake Shoe Liner by Using Composite and Nano Materials
Abstract: The mechanical performance of the brake shoe liners dictates the safety and efficiency of the vehicles; thus, brakes are very vital in ensuring controlled deceleration and stopping. In the past few decades, composites have significantly impacted the automotive industry through lighter, stronger, and sturdier alternatives to traditional materials improving overall performance. Nano additives are of key importance in such composites, improving not only the mechanical properties but, more significantly, the …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 280–295 Read article
-
The Role of Composite Materials in Electric Vehicles: Enhancements in Performance, Safety, and Efficiency
Abstract: Individuals outside the manufacturing industry may not be familiar with the remarkable characteristics of composite materials, which include an excellent strength-to-weight ratio, durability, and versatility. Composites lie at the crossroads of the automotive sector particularly in the electric vehicles (EVs). Much as this paper sought to discuss composites rich contribution to the EV technology, this paper deems it useful in the context of light weighting, battery and housing, and the …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 296–310 Read article
-
An Insightful Study on SMEDDS Challenges and Potential Strategies
Abstract: Self-microemulsifying drug delivery systems (SMEDDS) have gained attention as an effective approach to enhance the bioavailability of poorly water-soluble drugs. They are innovative lipid-based formulations designed to enhance the solubility, bioavailability, and therapeutic efficacy of poorly water-soluble drugs. The development of SMEDDS involves systematic selection of components based on solubility and emulsification efficiency, followed by optimization of ratios using pseudo-ternary phase diagrams. The resulting formulations are evaluated for droplet size, …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 311–334 Read article
-
Comparative Experimental Investigation of Infill Pattern and Infill Density on Fused Deposition Modeling (FDM) Process Characteristics of Polylactic Acid (PLA)
Abstract: Additive manufacturing is the potential and emerging technology widely being used to produce quality products with complicated profiles and customized features. Fused Deposition Modelling (FDM) process, a type of additive manufacturing technology using filament made of thermoplastic which is melted and subsequently extruded through nozzle. The main input process parameters of FDM are wall thickness, infill density, layer height, bed temperature, layer thickness, infill pattern, nozzle temperature etc. In this …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 335–345 Read article
-
Numerical Investigation on Medium Velocity Impact Response of Hybrid Metal Matrix Composite Laminate
Abstract: The current investigation centers on examining the numerical analysis of a hybrid metal matrix composite laminate resulting from impacts inflicted by diverse projectiles on the composite structure. Composite materials are chosen based on their inherent properties and compatibility in terms of bonding with other materials, forming the layers for the hybrid metal matrix composite. The fiber taken for the research paper was Kevlar and Sisal because they both bear good …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 346–358 Read article
-
Use of Geopolymers for Environmental Sustainability
Abstract: Geopolymers are a rapidly growing matter with enormous potential for improving environmental sustainability in the construction sector. This study highlights the use of geopolymers as eco-friendly alternatives to traditional building materials, with special emphasis on their role in reducing the environmental effect of construction operations. It also focuses on the chemical composition, mechanical characteristics, environmental sustainability, etc. of geopolymers, along with their benefits over conventional materials such as portland cement. …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 35–43 Read article
-
Effect of Surface Modification on Properties of Kevlar/Epoxy Polymer Composites
Abstract: In this study, a high-performance Kevlar/epoxy polymer composite was prepared using a hand lay-up technique. The Kevlar fiber was treated with calcium chloride/ethanol solution (CaCl2/EtOH) to enhance the interfacial interaction between the fiber and the epoxy matrix. The optimization of fiber surface treatment and fiber content for the best tensile strength (TS) of Kevlar/epoxy polymer composite was achieved using Box-Behnken design (BBD) through response surface methodology (RSM). Three parameters: CaCl2 …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 35–46 Read article
-
Assessment of Sustainable Composite for UAV structural Application
Abstract: Now-a-days aligned with global mission the growth of Unmanned aerial vehicle (UAV) application is enormous in the field of agriculture, defence, surveying etc., This research work investigates the improvement in strength of polymer matrix composite material of adding epoxy polymer resin with novel bio fibers such as Tamarindus and Morinda. The composite material was fabricated by using hand-layup method later its mechanical properties are analysed by numerical method as well …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 359–377 Read article
-
Automotive Plastics and Polymer Composites: A Road Map for Future Mobility of Electric Vehicles
Abstract: The automotive industry is in the process of achieving a major shift toward green vehicles faster than ever with the heightened demand for energy efficient products, namely EVs. This evolution is closely linked with use of such composite materials like plastics and polymer composites. Lithium manganates and other similar materials provide extraordinary benefits such as lightweight, high density energy storage capability, and affordable to manufacture. Due to its advantages in …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 378–392 Read article
-
Experimental Investigation on Strength and Durability Properties of Slag Based Alkali Activated Concrete Incorporating Fly Ash
Abstract: To minimize carbon emissions during cement production and to resolve landfill issues arising from industrial waste, the adoption of alkali-activated concrete (AAC) incorporating various by-products from industry has become increasingly popular as environmentally friendly option to conventional concrete in the construction sector. This study focused on strength and durability of AAC by utilizing waste industrial by-products such as ground granulated blast furnace slag (GGBS) and fly ash (FA) at ambient …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 393–400 Read article
-
Advanced Composite Materials for Electric Vehicle Charging Stations: A Comprehensive Study
Abstract: EV chargers are thought to be a major determinant in the adoption of EVs in present transport systems. The performance and durability of these charging stations highly depend on the materials applied in the construction of these charging stations because these materials should be very reliable, durable and efficient. The current paper reviews the current literature on advanced composite materials relevant in the construction of the EV charge station. Recognitions …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 401–415 Read article
-
Advancements in Polymer Composites for Hybrid Electric Vehicles: Market Potential and Future Directions
Abstract: Hybrid Electric Vehicles (HEVs) are essential for moving on the right track towards trying to achieve the future of sustainable transport by playing the following roles of increasing efficiency and reduction in emissions. Partner commodity materials contribute to this shift because of their features like lightweight and high-stiffness and are exemplified by polymer composites. These materials improve the HEV performance by enabling weight reduction of the vehicle, thus leading to …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 416–431 Read article
-
Development of Robot Arm Fingers with Polymer Soft Materials
Abstract: Lightweight soft material applications have attracted attention to Basalt Fiber Reinforced Polymer (BFRP) laminates because of their impressive mechanical characteristics. The impact response and stress-strain behavior of epoxy resin laminates armored with basalt fiber and banana fiber are investigated during this project using computational and experimental approaches. The hand lay-up method was employed to create laminates with a thickness of 3 mm, dimensions of 300x300 mm², and a layout of …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 432–439 Read article
-
Properties of Binary Waste Based Geopolymer Concrete Composite: A Review
Abstract: Concrete composite as construction material is utilized all over the world and it is not considered as eco-friendly because cement is provided as a binder in it. Therefore, replacing binder in concrete composite by alumina and silica rich by-products in presence of chemical activators give rise to geopolymer concrete composite which is eco-friendly in nature. Geopolymer concretes composite can be used to build a variety of structural configurations, have a …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 44–52 Read article
-
Heat Transfer Performance of ZnO- Ethylene Glycol- Water Nanofluid Using Thermal Lens Technique
Abstract: Nanofluids are engineered fluids used in advanced electronic systems for thermal management. Fluids with dispersed nanoparticles have exhibited remarkable thermal properties. Ethylene glycol (EG) and water mixtures are widely used in many industrial areas. This study investigates the synthesis and heat transfer performance of ZnO-EG, ZnO-water, and ZnO-EG-water nanofluids using a dual-beam thermal lens technique. ZnO is a widely used inorganic, UV-absorbing, multifunctional semiconducting material with applications in various fields …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 440–445 Read article
-
Quasi-Dimensional Thermodynamic Performance and Emission Modelling for Dual-Fuel SI Engine Operation Using Waste-Based Producer Gas and Methane
Abstract: Rising energy crisis and urgent need for better waste-handling techniques have gained significant attention. Integration of wastes-to-wealth and Green Energy evolution techniques are prime sustainable measures towards countering this menace. Moreover, Internal Combustion (IC) engines are significant energy consumers and their emissions play a major factor in global warming and ecological obliteration. Concerning these aspects, investigations should strive at emissions minimization and reutilization of low-impact industrial byproducts. Thus, using methane …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 446–458 Read article
-
Study on Fiber Reinforced Composite Material Cost in Construction Project
Abstract: The primary goal of this research paper is to identify the major causes of fibre reinforced composite material cost overruns in Indian construction projects, as well as the critical success factors that aid in the avoidance of such costs. The critical success factors is reviewed by existing literature. They are used to generate survey and interview questions. The fiber reinforced materials projects using proposed hypothesis and lack of certain critical …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 459–466 Read article
-
Mechanical and Environmental Performance of Curaua Fiber Composites: A Sustainable Alternative to Wood and PVC
Abstract: This study examines the mechanical behavior of curaua fiber composites, comparing their performance to other materials like wood and PVC. Curaua fibers, sourced from the Brazilian Amazon, demonstrate superior mechanical properties, making them a promising alternative for sustainable composite materials. The composites were fabricated using various methods and subjected to tensile, flexural, and impact tests. Results show that curaua fibers exhibit an average tensile strength of 30.7 MPa, outperforming wood …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 467–477 Read article
-
Tribological Assessment of Chemically Modified Jatropha Curcas Oil Developed by Addition of Graphite Nanoparticles for Biolubricant Applications
Abstract: As an alternative to petroleum-based lubricants, environmentally friendly bio-based lubricants are gaining popularity in the lubrication industry. A sustainable bio-based lubricant, Jatropha Curcas Oil (JCO) incorporates nanoparticles as additives. Nevertheless, this oil cannot be used directly as a biolubricant due to its low oxidative stability. By redesigning the oil's molecular structure through chemical modification, this restriction can be overcome. Epoxidation and oxirane ringopening were the two steps used in this …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 47–58 Read article
-
Optimizing Vehicle Structures Using Functionally Graded Materials of Aluminum and Carbon Fiber Reinforced Polymer Composites
Abstract: This article investigates the optimization of vehicle structures through application of functionally graded materials (FGMs), specifically aluminium and carbon fibre reinforced polymer (CFRP) composites. Such materials, known as FGMs, are characterized by spatial variations in composition and structure designed to improve so-called performance attributes. For the purposes of this research, the material properties of aluminium and CFRP composites are taken to be randomly distributed in thickness direction of a FGM …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 478–489 Read article
-
A Critical Review on Carbon Fiber Reinforcement in Various Applications
Abstract: Carbon fiber, celebrated for its outstanding mechanical properties and impressive strength-to-weight ratio, has become a critical material in various industries. This review journal, An In-Depth Study of Carbon Fiber Reinforcement in Diverse Applications, delves into the recent advancements and innovations in carbon fiber technology. The exploration includes its integration into aerospace, automotive, civil engineering, sports equipment, and renewable energy sectors. The aerospace industry leverages carbon fiber for constructing lightweight, fuel-efficient …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 490–502 Read article
-
A Review on Materials and Working Process Parameters of Selective Laser Sintering
Abstract: The potential for additive manufacturing technology to replace some of the current conventional manufacturing methods makes it one of the research and development fields that is expanding quickly. With additive manufacturing, three-dimensional physical models are produced layer by layer from computer-aided design (CAD) models. Fully dense metal things may be produced more rapidly and accurately with additive manufacturing. The Selective Laser Sintering (SLS) procedure uses powder bed fusion, in which …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 522–529 Read article
-
Performance and Robustness of Wind Turbine Blades Composed of Recovered Waste Carpet Fiber Polymer Composites
Abstract: Carpets stay in good condition for ten to fifteen years, after which they wear out and are discarded. The large amount of used carpet waste is often dumped in landfills, causing health risks, air pollution, and other environmental problems. To reduce the growth of landfill sites, it is essential to implement recycling measures for carpet waste, protecting the environment by reusing these materials in new products. Carpet are made from …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 53–66 Read article
-
Fabrication and Characterization of Almond Skin Powder Reinforced PLA Based Composite Filaments for Fused Filament Fabrication
Abstract: Researchers around the globe are increasingly utilizing recycling methods to address waste generated from polymers, spurred by the dire need to deal with environmental challenges promoting sustainable practices. Polymers are having highly-stable long-chain polymer structure which makes it difficult to degrade easily posing many environmental and health challenges, hence, recycling of the polymers is the sole method to mitigate harmful effects. However, there has been relatively little focus on producing …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 530–539 Read article
-
Advanced Polymer Composites for Energy Storage: Accelerating the Electric Vehicle Revolution
Abstract: The automotive sectors are going through dynamic changes as electric vehicles EVs are being adopted as sustainable solutions to the ever-emerging transport and environmental issues. The underpinning changes that are attributed to the transition process are the advancement in the energy storage systems which are central in improving the viability of the EVs. Of the emergent materials, polymer matrix composites have attracted much interest because of their features as lightweight, …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 540–549 Read article
-
Tribological Characteristics of Dental Crowns
Abstract: Dental tribology is an emerging field that focuses on improving the design and material choices for artificial dental systems. This paper looks at different dental crown materials, their clinical efficacy and the consequences of tribological wear on teeth due to interfacial movement. Ceramics are commonly utilized in fixed dental restorations because of their superior mechanical and cosmetic qualities, which include exceptional fracture resistance and clinical endurance. Ceramic crowns, often used …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 550–559 Read article
-
Aerodynamic Analysis of Foliage Stimulated Airfoil Design for Enhanced Strength with Carbon Fibre-reinforced Polymer
Abstract: Ever since the beginning of aviation, there has been an unwavering desire to improve airfoil design in order to improve aircraft performance. This insatiable desire for improvement has driven innumerable aerodynamicists to create a diverse range of revolutionary airfoils. This research investigates a revolutionary method to airfoil design, inspired by the complicated structures and aerodynamic qualities of natural leaves. Using biomimicry, the project seeks to increase the performance and efficiency …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 560–616 Read article
-
Enhancing Mechanical Properties of Fiber-Reinforced Composites Through Sorghum Husk and Unsaturated Polyester Resin.
Abstract: Plastic, a versatile synthetic polymer, holds considerable significance and utility in human society due to its manifold applications. However, its deleterious ecological ramifications have spurred growing apprehensions. This has galvanized the pursuit of ecologically amicable substitutes, propelling interest in the domain of composite materials. Composites are formulated by amalgamating diverse substances, and in this context, Styrene Diluted Unsaturated Polyester Resin (SDUPR) is melded with natural constituents. Among these organic constituents, …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 59–65 Read article
-
Study of Ablation Characteristics Carbon Fiber Reinforced Plastic with Silicon Carbide Pores
Abstract: Significant thermal stress is placed on spacecraft during atmospheric re-entry, primarily due to aerodynamic heating. This intense heat can cause severe material damage threatening the spacecraft's structural integrity. To address this challenge, efforts are focused on improving the ablation resistence of spacecraft components. In this work, carbon fiber reinforced plastic (CFRP) composites containing silicon carbide (SiC) holes are explored as a potential solution for enhancing thermal protection system. Four different …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 617–627 Read article
-
Mix Proportioning of Biochar as a Partial Replacement of Cement Using Alkaline Activators in Concrete Composite
Abstract: The growth of the world population has led to a heightened need for housing, making construction a crucial sector. Cement, a critical element in concrete mixtures, is indispensable in construction activities. Yet, the diminishing reserves of natural resources such as limestone and rocks, essential for cement manufacturing, necessitate sustainable options. This research investigates the creation of sustainable concrete blends by incorporating biochar and ground granulated blast furnace slag (GGBS), activated …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 628–639 Read article
-
Development of Eco-friendly Glass Fiber Composites Embedded with Paddy Stubble for Sustainable Applications and Its Metallurgical Characterization
Abstract: The extreme rise in environmental challenges owing to agricultural activities, among which paddy stubble burning remains a huge concern. Burning about 15 million tons of paddy stubble leads to emissions discharge of various toxic pollutants and gases notably, nitrogen oxides, methane and carbon monoxide in large scale causing global air pollution and climate change. The study focuses on obtaining and preparing a paddy stubble powder and using it with glass …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 640–648 Read article
-
Design, Analysis, and Testing of a Carbon Fibre-based Solid Rocket Motors
Abstract: The goal of the research is to simulate the outer shell of a rocket in order to fulfil mission criteria. Case failures can occur for a number of causes, including poor material selection, carelessness in the service conditions, inadequate non-destructive testing during crucial stages of production, and poor design and analysis. For this reason, it is crucial to simulate rockets with precise design and analysis. The study entails the designing …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 650–669 Read article
-
Enhancing The Mechanical Performance of Al6061/Graphite Composites Reinforced with Sic and Aluminium Oxide Processed by Stir Casting
Abstract: The study investigates the mechanical properties of aluminum alloy Al6061 reinforced with varying proportions of silicon carbide (SiC) (0 wt%, 4 wt%, 5 wt%, and 6 wt%) and aluminum oxide (Al₂O₃) (0 wt%, 4 wt%, 3 wt%, and 2 wt%), with a constant addition of 1 wt% graphite. The composites were fabricated using the stir casting process, an efficient and economical method for uniformly distributing ceramic reinforcements within the metal …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 66–74 Read article
-
Integrated Plasma Gasification Technologies for Enhanced Energy Conversion and Environmental Sustainability: A Short Review
Abstract: Plasma Gasification emerged as a constructive tool for waste management and cleaner energy production. The versatility of the process makes it a promising solution of the global energy crises. In this paper, a brief coverup is done of integrated plasma models. Plasma technology is an emerging solution for recycling a wide range of waste making it a highly sustainable, efficient, and environment-friendly process. The integration of Plasma Gasification with complementary …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 67–75 Read article
-
Non-contact Real Time Digital Distance Measurement System for Vehicle Applications
Abstract: An Arduino-powered Digital Distance Measurement System with LCD Display a compact and precise solution presents a practical and portable digital distance measurement system utilizing the versatility of Arduino microcontrollers and the accuracy of ultrasonic sensors. This system can be utilised for airplane docking system which measures the distance exactly. Leveraging Arduino’s programming capabilities and readily available libraries, the system transmits ultrasonic pulses and analyses the reflected echoes to calculate real-time …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 670–678 Read article
-
Enhancing Mechanical Properties by Parameter Optimization in Fiber and Particle Reinforced Composites
Abstract: This research focuses on optimizing the mechanical and thermal properties of hybrid fiber and particle-reinforced composites through systematic parameter optimization using the Taguchi method and Grey Relational Analysis (GRA). Composites were fabricated using varying fiber volume fractions (20%, 30%, and 40%), particle sizes (20 μm, 60 μm, and 100 μm), and curing temperatures (60°C, 80°C, and 100°C) in a 3-factor, 3-level experimental design. Key properties such as tensile strength, impact …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 75–85 Read article
-
An Analysis of Machining Parameters for Metal Matrix Composite
Abstract: The electro-discharge machining analysis of hybrid Composite is presented in this work. Variables are chosen for the input process parameters. The material removal rate is acknowledged as an output parameter, together with the current, graphite and silicon carbide percentage and pulse on time. We used the Taguchi Method to conduct our experiments. To create the theoretical model and look into how process parameters affect the rate at which material is …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 76–85 Read article
-
A Polymer-Based Recommender System for Precision Agriculture: Enhancing Crop Yield Analysis Using IoT Technology
Abstract: This study introduces an innovative recommender system that employs polymer-based sensors combined with advanced data analytics to deliver personalized recommendations for crop management optimization. The use of polymer-based materials in sensor design allows for the creation of durable, cost-effective, and efficient sensors, well-suited for the challenging conditions typical in agricultural environments. These sensors are designed to withstand variations in numerous factors like temperature of the surrounding, humidity level, and at …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 86–95 Read article
-
Analyzing The Mechanisms of Polymerization and The Related Kinetic Pathways Using Refined Analytical Methods.
Abstract: In numerous sectors, polymeric materials play a crucial role, yet effectiveness is largely determined by their molecular structure and the processing parameters utilized. This investigation presents an integrative approach aimed at delineating the connections between polymer structure, properties, and processing through sophisticated characterization methods. With the implementation of small angle X Ray Scattering (SAXS),NMR(Nuclear magnetic resonance( spectroscopy) FM(Atomic Force Microscopy) and rheological analysis, we analyze the complex interplay between molecular …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 86–94 Read article
-
Design and Performance Analysis of Sustainable Hybrid Composites for Impact Absorption and Lightweight Applications.
Abstract: This study explores the mechanical and structural properties of a novel hybrid composite composed of recycled tyre rubber, ceramics, and wood. The investigation focuses on key parameters, including energy absorption, compressive and tensile strength, and density, to evaluate the composite's suitability for diverse applications. The impact energy absorption test revealed that Sample A, comprising 50% rubber, 25% ceramic, and 25% wood, exhibited the highest energy absorption capability, with an average …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 95–104 Read article
-
Advancements In Metal-Fiber Composites for Aerospace and Defense Applications: A Comprehensive Review
Abstract: This paper provides a comprehensive review of fiber-reinforced composites, focusing specifically on the utilization of metal-fiber composites in aerospace such as metal surface preparation prior to bonding, resin selection, and detailed examination of mechanical testing and impact studies. The significance of metal surface preparation for establishing strong bonding, which is a crucial initial step in composite fabrication, is discussed. Additionally, the prevalent use of epoxy resins and their importance in …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 96–108 Read article