Search
52 articles for “Residual Stresses”
-
Investigation of Residual Stress, and corrosion behavior of AA6082/Al 2 O 3 /C/ Si 3 N 4 Composite Material
Abstract: The main objective of the current study was to create AA6082/ Al2O3/C/Si3N4 Composite Material by the use of stir casting. The properties of the AA6082/ Al2O3/C/ Si3N4 Composite Material shown a significant improvement, with a micro-hardness rise of 13.5% and a residual stress decrease of 60%. As the testing parameters were increased, the residual stress of the AA6082/ Al2O3/C/ Si3N4 Composite Material rapidly decreased from -65MPa to -15MPa. An electromagnetic …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 1104–1109 Read article
-
Simulation of Dual Microstructure Heat Treatment Process and Residual Stresses in Gas Turbine Disc by DeformHT Software
Abstract: Gas turbine disc is one of the most vital components in advanced gas engine. In order to improve the tensile strength and fatigue strength of the disc, finer grain size is to be attained at bore area and coarser grain structure at rim area in order to resist the growth of creep. Attempts have been made by several researchers experimentally on the development of dual microstructure for Inconel-718 by heat …
Published in Journal of Materials & Metallurgical Engineering · Vol. 7, Issue 1, 2017 · pp. 30–42 Read article
-
Experimental Analysis of Residual Stress, Micro-Hardness and Corrosion Behavior of HVOF Sprayed Composite Coating
Abstract: The utilisation of non-traditional composite coating materials, enhanced lubrication, and surface geometry optimisation have all contributed to the tribological performance. Piston rings are among the most crucial engine parts since friction causes between 40 and 45 percent of all energy loss. Fuel efficiency, power loss, and exhaust pollutants are all strongly impacted by the piston assembly's tribological performance. The present study's primary goal was to develop composite coating by using …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 77–82 Read article
-
Parametric optimization of residual stress of TiO2 composite coating
Abstract: The primary objective was to develop a composite coating by utilizing the HVOF thermal spray technique and including TiO2. The substrate was covered with a high-quality composite layer utilizing the HVOF coating process. The TiO2-based powder and carbon powder were initially combined in the mixer for deposition. The composite powders were applied via an HVOF torch, namely the PT F4 model. The firearm frequently produces a high-speed flow of extremely …
Published in Journal of Polymer & Composites · Vol. 12, Issue 2, 2024 · pp. 295–301 Read article
-
Novel Catalytic Strategies for Reducing Residual Stresses and Improving Surface Quality in Machined Ceramic Materials
Abstract: To prepare for material cutting and utilize utility-specific edges, it’s crucial to understand the inherent brittleness of ceramics. This brittleness limits the forming methods available and hinders achieving dimensional accuracy and precision through conventional machining techniques. The fabrication of composite materials is becoming increasingly significant, particularly in technical fields like the automotive industry, where they are used to manufacture engine connecting rods, propeller shafts, brake discs, and more. The machining …
Published in Journal of Catalyst & Catalysis · Vol. 11, Issue 2, 2024 · pp. 01–07 Read article
-
Prediction of temperatures and residual stresses during FSW of AA2024 and AA7075 with copper using HYPERWELD software
Abstract: This paper investigates the temperature at different workpiece and tool pin sections. In this investigation, various materials are utilized, for example, AA7050, AA2024, and Copper, for other process parameters. Tool rotational speed, tool tilt angle, and welding speed are process parameters. Thermal distribution results are examined with the assistance of these process parameters. Altair’s Hyper Weld, a preeminent computer-aided engineering (CAE) application for the simulation of friction stir welding, has …
Published in Journal of Polymer & Composites · Vol. 11, Issue 12, 2023 · pp. 101–112 Read article
-
Evaluation of Critical MMAW Welding Defects Using Computer Simulation in Industrial Manufacturing Systems
Abstract: Manufacturing is one of the key sectors of any countries GDP and welding is one of the prime manufacturing processes of the manufacturing sector. Welding has several notable advantages over mechanical joining techniques, including higher structural integrity, design flexibility, and cost and weight lowers. Welded products/structures are subjected to serious issues of residual stresses and distortions. The performance and sturdiness of the welded structures are severely impacted by weld remaining …
Published in International Journal of Industrial and Product Design Engineering · Vol. 3, Issue 2, 2025 · pp. 18–26 Read article
-
A Review on Pressure Die Casting Technology and Recent Developments in Die Design
Abstract: A high production rate and cost effective method primarily used in the production of non-ferrous castings is the Pressure Die Casting (PDC) technology. It is widely used in the manufacturing of automobile components of complex geometry and intricate forms and shapes that may be difficult to produce by the other conventional casting processes. This paper gives an insight into the types of pressure die casting techniques. It also describes the …
Published in Trends in Mechanical Engineering & Technology · Vol. 8, Issue 2, 2018 · pp. 85–99 Read article
-
Correlation Between XRD Analysis and Mechanical Characterization Using Lens Manufactured Specimens Based on IoT Sensors
Abstract: The advent of the Internet of Things (IoT) has enabled the seamless integration of sensors into the manufacturing process, facilitating the collection of real-time data for analysis and optimization. The correlation between X-ray diffraction (XRD) analysis and mechanical characterization is investigated using specimens manufactured through the Laser Engineered Net Shaping (LENS) technique. The study focuses on three different materials: brass, SS202, and SS304. XRD analysis is employed to determine the …
Published in Journal of Polymer & Composites · Vol. 12, Issue 2, 2024 · pp. 41–58 Read article
-
Computational investigation of the influence of process parameters of 3D printed PLA material
Abstract: This study uses numerical simulation to examine the relationship between critical process parameters say, feed rate, layer height, and raster angle, on residual stresses and distortions and on the achievable density of FFF prints to identify the optimal input parameter combinations for ISO 527-2 type 1A. Methods of additive manufacturing that are utilised widely used to manufacture thermoplastic parts is fused filament fabrication. High residual stresses are one of the …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 259–269 Read article
-
Effect of PWHT Cycle on Microstructure and Mechanical Properties of 1.25Cr-0.5Mo Weld
Abstract: Post Weld Heat Treatment (PWHT) is a process of reducing residual stresses and enhancing material properties of any material after welding. The process depends on many parameters like type of material, the thickness of material, PWHT temperature, soaking time, heating and cooling rate, etc. The Post Weld Heat Treatment process of material could effect on tensile strength, impact toughness, hardness, microstructure, etc. If the Process of PWHT is performed incorrectly …
Published in Journal of Experimental & Applied Mechanics · Vol. 10, Issue 1, 2019 · pp. 7–16 Read article
-
Effect of Post Weld Heat Treatment on Mechanical Properties and Microstructure of P11 Weld: A Review
Abstract: Post weld heat treatment (PWHT) is a process of reducing residual stresses and enhancing material properties of any material after welding. The process depends on many parameters like type of material, thickness of material, PWHT temperature, soaking time, heating and cooling rate, etc. Post weld heat treatment is a process of material that could result detrimental effects on tensile strength, yield strength, impact toughness, hardness, elongation, etc. If the process …
Published in Journal of Experimental & Applied Mechanics · Vol. 8, Issue 3, 2017 · pp. 43–47 Read article
-
Assessment of Matrix Cracking and Fiber Breakage in Hybrid Composite Materials.
Abstract: Hybrid composite materials, combining two or more distinct fiber or matrix constituents, have emerged as advanced structural solutions for aerospace, automotive, marine, and civil engineering applications. However, their complex microstructure makes them susceptible to multiple interacting damage mechanisms, particularly matrix cracking and fiber breakage. This study provides a comprehensive assessment of these damage modes, emphasizing their initiation, evolution, and combined effects on the mechanical integrity of hybrid composites. Matrix cracking …
Published in International Journal of Fracture Mechanics and Damage Science · Vol. 3, Issue 2, 2025 · pp. 1–5 Read article
-
A Study on Recent Trends in IC-Mems Integration
Abstract: MEMS devices are incorporated with IC technologies because of its miniature size, efficient functionality and broad range of applications. The technology involved is capable of integrating both electrical and mechanical systems. MEMS are nowadays used extensively in real time applications which outperforms other traditional designs with its innumerous advantages. This paper reviews the various implementation techniques of MEMS sensors integrated with IC’s. Electronic Vehicle Identification (EVI) is done with the …
Published in Recent Trends in Sensor Research & Technology · Vol. 8, Issue 1, 2021 Read article
-
Condition Monitoring of a Round Bar with a Defect Using Vibration Analysis
Abstract: As an energy-saving and high-efficient stress relieving process, vibratory stress relief [VSR] influence of on fatigue life is still explicit and needs further investigation. Standard specimens are manufactured to study the VSR effects on 2014 T6 aluminum alloy fatigue behavior. Dynamic stresses generated during vibration are measured by strain gauge and the residual stresses with and without VSR are compared to validate the stress relieving effects. Eventually, fatigue tests are …
Published in Trends in Machine design · Vol. 6, Issue 2, 2019 · pp. 5–7 Read article
-
Bio-Inspired FGPCs for Biomedical and Structural Applications
Abstract: Bio-inspired functionally graded polymer composites (FGPCs) represent a new class of smart materials that use gradient material distributions to enhance mechanical and biological properties, mimicking natural systems like bones, shells, and plant stems. FGPCs exhibit smooth gradient distributions across interfaces, which improves biocompatibility and reduces the risk of failure under complex loading and environmental conditions. In this study, bio-inspired FGPCs were designed, fabricated, and validated using a combined experimental and …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 456–481 Read article
-
Effect of Solution Heat Treatment and Aging on the tensile Properties of Ti-6Al-4V Alloy Component Manufactured by Wire Arc Additive Manufacturing
Abstract: Wire Arc Additive Manufacturing (WAAM) is a cost-effective technique for fabricating components from the Ti-6Al-4V alloy, known for its high strength and utility in demanding applications. To maximize its strength, the alloy undergoes Solution Treating and Aging heat treatment, comprising three key steps: (i) Solution Treating: The alloy is heated to 950°C (just below the β transus) and held for 1 hour, increasing the β phase proportion. This step sets …
Published in International Journal of Machine Systems and Manufacturing Technology · Vol. 3, Issue 2, 2025 · pp. 1–6 Read article
-
Studies of Tin Whisker Formation and Destruction
Abstract: This article contains whisker growth in current implements considered in electronics packaging. These surface relief growths are said contemporarily to prevent and save devices after Pb abatement. Vacancy flux at crack created from compressive stresses cause mass transfer to guide oxides for direct and control of whiskers. Logical subject to shift mass from equiax to migrating morphologies of equiax such as columns. Criteria from past theories for Sn whisker growth …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 7, Issue 3, 2020 · pp. 26–34 Read article
-
Experimental and Process Optimization Study on Thermal Stress Reduction in TiC–Steel Brazed Joints Using Polymer-Derived Composite Interlayers
Abstract: In this, an experimental investigation aimed at reducing crack formation due to thermal stress in TiC-steel brazed joints through optimization of key process parameters is presented. The primary objective was to develop an integrated and reliable brazing strategy by examining the effects of filler material selection, brazing gap, cooling conditions and type of flux. In this study, polymer-derived composite interlayers were developed through controlled synthesis and nanocomposite engineering to mitigate …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 524–540 Read article
-
Adhesively Bonded Patch Repair in Polymer Composites: Effects of Reinforcement Configuration and Post-Cure Temperature
Abstract: Adhesive patch repair technique has been identified as an effective and economical approach to repair damaged polymer composite structures that are used in aerospace, automotive, marine, wind energy, and many other high-performance engineering applications. Adhesive bonding offers superior stress distribution, reduced stress concentration, less structural weight and fatigue resistance, and thus increases the lifetime of the repair of composite structures when compared to the traditional mechanical attachment approaches. Performance and …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 991–1001 Read article