Search
129 articles for “cutting process parameters”
-
Realization of Fourth Order Multifunction Filters Using Operational Transresistance Amplifier
Abstract: Design of analog filters, using single Operational Transresistance Amplifier (OTRA) as the active current mode building block, is presented. Five types of filters have been designed namely Low Pass, High Pass, Band Pass, All pass, and Notch. The order of the proposed filters is four. The theoretical results are verified with PSPICE simulation using 0.5m CMOS process parameters provided by MOSIS (AGILENT). Frequency responses for the presented filters are shown …
Published in Journal of Electronic Design Technology · Vol. 3, Issue 1-3, 2012 · pp. 65–71 Read article
-
Design and Development of Multistep Boring Tool
Abstract: Boring is the process to enlarge the diameter of hole or employed for finishing operation in machine shop. It is a process in which drilled hole, casting hole, forged hole diameter are increased by cutting device known as boring tool. Boring operation is generally conducted to enlarge the hole’s diameter. Spindle speed, cutting speed, feed rate and torque are very important parameters to be considered while designing the boring tool. …
Published in Trends in Machine design · Vol. 2, Issue 3, 2015 · pp. 39–46 Read article
-
A Review on Effect of EDM Parametrs on Die Sinking EDM
Abstract: Electric discharge machining (EDM) is a nonconventional method of machining conductive and hard to machine materials and obtaining intricate shapes. It is a controlled method of melting and vaporizing the work piece by series of electric discharges between the tool and the work piece. In EDM there are a number of process parameters which must be selected sophisticatedly for obtaining reliable products thus optimization of EDM process parameters is important. …
Published in Trends in Mechanical Engineering & Technology · Vol. 5, Issue 1, 2015 · pp. 26–30 Read article
-
Evaluation of Abrasive Grinding Parameters in Crankshaft Manufacturing
Abstract: Grinding is a metal cutting operation performed by means of rotating abrasive tool, called “Grinding wheel”. Grinding is done on surface of almost all conceivable shapes and materials of all kinds. In grinding, it is possible to achieve very accurate dimensions and smoother surface finish in a very short time and it is only a method after hardening. High temperature to the tune of the 1000 to 1400°C is usually …
Published in Trends in Mechanical Engineering & Technology · Vol. 9, Issue 3, 2019 · pp. 13–15 Read article
-
Evaluation of process paramters of various materials by turning operation using different methodology techniques-A review
Abstract: The use of engineering materials has increased to a great extent in industries. So it is required to find the optimum parameters in order to have easy and economical machining. Turning operation is most important in the machining process. Especially of hard materials it is difficult sometimes to do so. For better results, the selection of proper process parameters is very important. This paper presents, the effect of process parameters …
Published in Trends in Mechanical Engineering & Technology · Vol. 10, Issue 3, 2020 · pp. 36–43 Read article
-
Optimization of Turning Process Parameters by Genetic Algorithm Approach
Abstract: In this research, turning parameters were optimized through a genetic algorithm for the purpose to minimize surface roughness and to maximize the material removal rate. High finish quality is guaranteed through minimum surface roughness, and efficient process planning is facilitated through maximum material removal rate optimization. For predicting surface roughness and material removal rate with respect to spindle speed, feed rate, and depth of cut, the empirical models were developed …
Published in Journal of Production Research & Management · Vol. 15, Issue 1, 2025 · pp. 33–41 Read article
-
Evaluation of Abrasive Grinding Parameters in Crankshaft Manufacturing
Abstract: Grinding is a metal cutting operation performed by means of rotating abrasive tool, called “Grinding wheel”. Grinding is done o surface of almost all conceivable shapes and materials of all kinds. In grinding it is possible to achieve very accurate dimensions and smoother surface finish in a very short time and it is only a method after Harding. High temperature to the tune of the 1000 degree Celsius to 1400 …
Published in Trends in Machine design · Vol. 7, Issue 1, 2020 · pp. 28–33 Read article
-
Experimental Investigation of Process Parameters While Milling of AA8011 Using MCDM/MADM Method-TOPSIS
Abstract: This paper presents in-depth and comprehensive approach for optimizing the machining parameters in milling of wrought alloy AA8011 using a MCDM/MADM method called TOPSIS. The present work is carried out in three phases; in the first phase the orthogonal array L27 design is prepared using Minitab software by considering various milling parameters such as speed, feed and depth of cut at three different levels. In the second phase, milling operations …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 1, 2018 · pp. 11–16 Read article
-
Experimental Investigation of Process Parameters While Milling of AA8011 Using MCDM/MADM Method-TOPSIS
Abstract: This paper presents in-depth and comprehensive approach for optimizing the machining parameters in milling of wrought alloy AA8011 using a MCDM/MADM method called TOPSIS. The present work is carried out in three phases; in the first phase the orthogonal array L27 design is prepared using Minitab software by considering various milling parameters such as speed, feed and depth of cut at three different levels. In the second phase, milling operations …
Published in Journal of Production Research & Management · Vol. 8, Issue 2, 2018 · pp. 1–7 Read article
-
Various Methods For Plastic Waste Pyrolysis To Fuels: A Review
Abstract: The world's decreasing oil reserves and increasing energy demands are pushing experts to explore alternative ways of producing premium oils that can replace fossil fuels. Waste-to-energy recovery, which involves converting waste materials into energy, shows great potential for managing waste. Waste plastics, abundant and with a high combustion heat, are attractive for energy conversion. However, the vast use of plastic products, both industrially and domestically, leads to a surge in …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 79–93 Read article
-
Cytogenotoxicity Assessment of Asphalt Plant Discharge Water using Plant Assay
Abstract: The Allium cepa assay test was used to evaluate cytogenotoxic effects of asphalt plant discharge water at the concentrations of 10, 20, 30, 40, 50, 60, 70, 80, 90 and 100% (v/v) asphalt plant discharge water/distilled water. The distilled water served as the negative control. The analysis of the physicochemical properties and heavy metals concentrations showed that most parameters were higher than the established standards of WHO and FMENV. The …
Published in Journal of Water Pollution & Purification Research · Vol. 12, Issue 3, 2025 · pp. 100–110 Read article
-
Machining-Induced Surface Integrity Optimization of High-Carbon Alloy Steel for Enhanced Polymer–Metal Composite Interface Performance
Abstract: The functional performance and structural reliability of polymer–metal hybrid composites are strongly influenced by the surface integrity of metallic substrates used for interfacial bonding and load transfer. In this context, machining-induced surface characteristics play a critical role in determining adhesion behavior, dimensional stability, and mechanical compatibility within composite architectures. The present study investigates the hard turning performance of a newly developed high-carbon alloy steel intended for composite-integrated structural applications, with …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1531–1546 Read article
-
Different Aspects to Achieve the Hole Quality in Gun Drilling Machining
Abstract: The manufacturing industry is always trying to fulfill the requirement of various industries and developing facilities to manufacture the designed parts. Many applications for various industries demand for deep drill where the ratio of depth of the hole to the diameter is greater than twenty. Gun drilling, B.T.A. drilling and ejector drilling are the three drilling processes to make deep holes. In the gun drilling process the pressurized oil is …
Published in Journal of Production Research & Management · Vol. 6, Issue 1, 2016 · pp. 34–38 Read article
-
Analysis and Improvement in Tribological Properties of Coated HSS Tool
Abstract: The use of low friction coatings like TiAlN and AlCrN is to improve the tribological properties of tools for metal cutting, forming and machine elements. It is strong scientific interest to conduct fundamental tribological research on the materials that exhibits low friction and can be used for surface coating on surfaces to rub against with reduced friction and wear. Parameters influence the quality of the products in turning process. The …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 5, Issue 1, 2018 · pp. 23–36 Read article
-
Numerical Simulation of Hybrid GSA Based Optimal Power Flow for Multi Objective Optimization Strategy
Abstract: Restricted nonlinear optimization in electric power systems engineering is a topic of Optimal Power Flow (OPF) that has been extensively investigated. It has been a long and remarkable history for the OPF, which was founded in the 1960s, of research and publication. Newcomers to OPF research face a challenging undertaking since there is so much information available and because OPF's popularity within the electric power systems community has prompted authors …
Published in Journal of Instrumentation Technology & Innovations · Vol. 11, Issue 3, 2021 · pp. 24–32 Read article
-
Finite Element, Experimental, and Machine Learning-Based Optimization of Machining Stability for Polymer Composite Material Processing
Abstract: The machining of polymer composite materials, particularly fibre-reinforced polymer-matrix composites, requires stable spindle-tool performance to avoid delamination, fibre pull-out, matrix cracking, thermal softening, poor surface integrity, and premature tool wear. In line with the scope of the Journal of Polymer & Composites, this study presents an integrated finite element, experimental, and machine learning framework for improving machining stability during end-milling of composite material systems. The spindle-tool assembly is modelled using …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 Read article
-
A Technical Review on Evaluation of Vegetable Oil in Water-Emulsion Cutting Fluid in Machining Steel with Coated Carbide Tool
Abstract: In metal cutting industries, Metal working fluids (MWFs) or Metal cutting fluids (MCFs) are used; they act as coolant as well as lubricant. In industries synthetic and petroleum based cutting fluid as well as coolant produce negative effect on human health, ecology and environment. When tool and work piece are engaged with each other while machining due to engagement they produce heat. The metal cutting fluids effect on heat generation …
Published in Journal of Materials & Metallurgical Engineering · Vol. 7, Issue 3, 2017 · pp. 26–34 Read article
-
Enhancing Cooling Efficiency in Dual Nozzle CO2-Based Vortex Tube Systems for Machining Titanium Alloys: Implications for Polymer and Composite Processing
Abstract: In machining of Titanium alloys, the cutting temperature plays a vital role that directly influences the performance and it is required to maintain as low as possible. In this study, a dual nozzle Vortex Tube Cooling System (VTCS) that supplies cool compressed CO2 gas is developed to reduce the cutting temperature in Ti-6Al-4V machining. The experiments were conducted at constant cutting and flow parameters during turning at different levels of …
Published in Journal of Polymer & Composites · Vol. 12, Issue 5, 2024 · pp. 284–291 Read article
-
Investigation on Torque and Thrust Forces in Radial Drilling of Copper Alloys
Abstract: As a part of research over improvement of machining process; cutting forces, metal removal rate (MRR) and surface finish on mechanical elements has become quite significant in the operational and aesthetical point of view. To enhance accuracy and precision by adopting energy saving techniques, manufacturing firms are adopting automated systems in order to achieve manufacturing excellence. In the present work, the effect of various process parameters like spindle speed, feed, …
Published in Journal of Materials & Metallurgical Engineering · Vol. 6, Issue 2, 2016 · pp. 6–19 Read article
-
Experimental Investigations of Mechanical Properties of Friction Stir Welded Joints of Aluminium Alloys AA6063 and AA6082
Abstract: One of the advantages of friction stir welding process is its ability to join dissimilar metals and alloys. The objective of this study was to study the possibility of joining two dissimilar Al alloys, typically A6082 and A6083 using in FSW. In this experiment, joint properties of A6082 and 6063 were studied. Three parameters considered were tool rotation speed, welding speed, depth of cut with three levels; and nine runs …
Published in Journal of Experimental & Applied Mechanics · Vol. 8, Issue 2, 2017 · pp. 45–52 Read article