Search
204 articles for “comparator circuit”
-
Design and Analysis of Bootstrap Sample and Hold Circuit
Abstract: This paper describes the design and implementation of open-loop sample and hold-circuit using bootstrap technique, which can be used as front end sampling circuit for high-speed analog-to-digital converters. Different design criteria, viz., speed, power, resolution, linearity, noise and harmonic analysis have been dealt with. Both theoretical analysis and simulation results are carried out. The bootstrap circuit is designed and then compared in a 0.18 and 0.35 μm CMOS process. It …
Published in Journal of Electronic Design Technology · Vol. 5, Issue 3, 2014 · pp. 7–14 Read article
-
Cell Balancing in Lithium-ion Batteries – A Comparative Evaluation
Abstract: Balancing the cells within a battery system is essential for safeguarding against overvoltage, overcharge, and over-discharge, which can lead to system failures and safety hazards. Two commonly employed methods for cell balancing are passive and active balancing. In passive balancing, excess charge is dissipated through resistors, while active balancing involves the controlled flow of charge within the circuit. This paper focuses on the comparison and analysis of passive and two …
Published in Journal of Power Electronics and Power Systems · Vol. 14, Issue 1, 2024 · pp. 37–45 Read article
-
Light Sensor Circuit
Abstract: The presence of light increases current in the photo diode or phototransistor. LM317 supplied lower voltage DC power in the circuit. Capacitors are connected in parallel with the DC output in order to filter out any high frequency AC signal coming from the noise. NE555P Timer produced accurate oscillation. BPV11 is used as a photodiode. LM311 is the comparator and the light on/off is converted to low/ high of the …
Published in Trends in Electrical Engineering · Vol. 9, Issue 2, 2019 · pp. 7–11 Read article
-
High Speed and Low Power Basic Digital Logic Gates, Half-Adder and Full-Adder Using Modified Gate Diffusion Input Technology
Abstract: In this paper, modified gate diffusion input (MGDI) technology has been used for the design and implementation of digital integrated circuits (ICs). In today’s digital world, IC plays a vital role in high-performance computing, communication, and many consumer electronics. IC manufacturing technology has scaled down to smaller device dimensions. This scaling has a great impact on the design of digital ICs. The main objective of the IC manufacturing technology is …
Published in Journal of VLSI Design Tools and Technology · Vol. 8, Issue 1, 2018 · pp. 34–42 Read article
-
CFD Analysis of Six-Flow Microchannel Heat Sink Using the Different Nanofluid
Abstract: In this study, we compare the heat-conveying capabilities of ordinary water with those of cooling fluids such as Ag-Water, TiO2-water, and Al2O3-water nanofluid at a volume percentage of 0.50%, and we also examine the six flow micro-channels of the fin-equipped heat sink. Hardware like microprocessors and integrated circuits are not used in the comparison. To evaluate the effectiveness of different cooling fluids, a number of thermal metrics are used, such …
Published in Journal of Polymer & Composites · Vol. 11, Issue 11, 2023 · pp. 1–11 Read article
-
Performance Analysis of Schmitt Trigger Circuit for Noise-Free Chips
Abstract: At lower nodes of complementary metal-oxide semiconductor (CMOS) technology, noise within a chip increase due to a drastic increment in interconnects within a given area. To improve the noise immunity of a chip, a Schmitt trigger circuit is used as a buffer instead of a simple CMOS inverter at various intervals along the metal interconnect. The use of a Schmitt trigger circuit not only makes the chip noise immune but …
Published in Journal of VLSI Design Tools and Technology · Vol. 14, Issue 3, 2024 · pp. 11–20 Read article
-
Visible and Infrared Light Detection
Abstract: A circuit is made to detect either visible or infrared light. It is designed by using different light detectors, such as, infrared phototransistor, visible phototransistor, and photoresistor. If no light is shining on the detector in the circuit, the green LED is flashing. When the light is shining on the detector, the red LED starts flashing instead of the green one. Op-amp LMC 6482 builds up a simple voltage follower …
Published in Trends in Electrical Engineering · Vol. 9, Issue 2, 2019 · pp. 20–26 Read article
-
Design and Analysis of Low-Power CMOS Inverter Chains for High-Speed Digital Circuits
Abstract: This report briefly explains the design process, structure, and evaluation of a CMOS inverter designed using a 45 nm technology process with a focus on its propagation delay and power consumption. Moreover, the CMOS inverter design will be created using the Cadence Virtuoso design environment, along with a post-layout analysis of the design. Performance evaluation of the designed circuit will be carried out through the execution of a transient analysis …
Published in Journal of VLSI Design Tools and Technology · Vol. 16, Issue 1, 2026 · pp. 40–57 Read article
-
Exploring the Potential of Adiabatic Logic for Low Power Nano-scale VLSI Designs
Abstract: Low power dissipation has emerged as one of the main research areas due to the ongoing scaling down of device technology in the area of VLSI circuit design. Adiabatic logic gates are a practical answer to the rising demand for low power portable gadgets. Various adiabatic logic families, including 2N-2N2P, PFAL (Positive Feedback Adiabatic Logic), DCPAL (Differential Cascode and Pre-resolved Adiabatic Logic), and a suggested circuit centred on the PFAL …
Published in Journal of VLSI Design Tools and Technology · Vol. 13, Issue 1, 2023 · pp. 6–14 Read article
-
Maximum Power Point Tracking for Solar PV System
Abstract: There is an ever increasing demand for energy in today's world. The photovoltaic (PV) systems are the suitable options for satisfying an ever increasing need for energy and thus are being used widely around the globe. Some special methods are required for extracting the maximum available power out of PV systems because they are nonlinear in nature. The nonlinear characteristic of the IV curve of PV module has a unique …
Published in Journal of Electronic Design Technology · Vol. 7, Issue 1, 2016 · pp. 14–21 Read article
-
Effects of Supply Voltage on 6T CNT Based Schmitt Trigger
Abstract: In this growing and developing age of technology, we are needed to improve our methods in order to get better results. So taking this into account, in electronic field, we want circuits with low propagation delay, leakage current and leakage power. So, we compared the model of Schmitt trigger using C-MOS (Complementary mosfet) and CNT (carbon nanotube) technology. We performed the variation in power supply (varied from 0.1to 1.2 V) …
Published in Journal of Power Electronics and Power Systems · Vol. 8, Issue 2, 2018 · pp. 19–24 Read article
-
Design and Implementation of High-Speed Low Power Low Area Hybrid One Bit Full Adder Using CMOS Technology
Abstract: In this article, we'll take a look at a new kind of Full Adder (FA) design that mixes traditional Complementary Metal Oxide Semiconductors (CCMOS) with Pass Transistors (PTs) and Transmission Gates (TGs). To analyze the circuit's performance, we used the Mentor Graphics software package. Since all twenty (20) varieties of Full Adder circuits were able to be measured and compared, this research was conducted. When the clock rate of the …
Published in International Journal of VLSI Circuit Design & Technology · Vol. 1, Issue 2, 2023 · pp. 29–39 Read article
-
Comparative Analysis of Class-AB Voltage Follower using DTMOS Transistor
Abstract: This paper describes a topology of voltage follower Class-AB Voltage Follower like Translinear voltage follower using MOS and DTMOS Transistor. The circuits are simulated in 90 nm technology. The results are used to compare the performance of the above voltage followers. All analysis was supported by the simulation results. The analysis are made in terms of gain, bandwidth and transient response using ELDO spice, IC station and Design architect of …
Published in Journal of VLSI Design Tools and Technology · Vol. 5, Issue 2, 2015 · pp. 64–70 Read article
-
Transistor Full Adder: A Comparative Performance Analysis
Abstract: AbstractIn this work the static energy recovery full adder named 10T13A with reduced 10 transistors is implemented. The fan in and fan-out of gates is also reduced by reducing number of transistors. Calculation of 10T13A full adder various parameters has been at 45 nm technology and compared with MTCMOS technique based 10T13A Full Adder. The active power has been calculated at 45 nm technology using Cadence Virtuoso Tool. Simulation results …
Published in Recent Trends in Electronics Communication Systems · Vol. 5, Issue 3, 2018 · pp. 22–31 Read article
-
Noise Analysis of Single-Ended Input Differential Amplifier (MOS) using Stochastic Differential Equation
Abstract: AbstractIn this paper, we do the noise analysis of single-ended input differential amplifier (MOS). Stochastic differential equations are used to analyse the effect of extrinsic noise. We use time domain method and use SDE (Stochastic Differential Equation) to determine autocorrelation function for the output process. Mean and variance of the output noise is obtained. This analysis helps to get circuit with better noise performance. The analysis compares the noise performance …
Published in Journal of Microwave Engineering and Technologies · Vol. 4, Issue 3, 2017 · pp. 19–25 Read article
-
The Analysis of Bridge Rectifier Circuits using Mathematica
Abstract: This paper addresses the steady-state and transient analysis of bridge rectifiers. It starts withsuggesting an efficient representation of the diodes. A single equation that describes thediode’s performance in both the forward and reverse directions is presented. It implicitlytakes the voltage polarity into account. Without any loss of generality, the suggested method isapplied to the classical uncontrolled four-valve full-wave rectifier bridge configureuration.The effect of the load resistance and the eventual presence …
Published in Trends in Electrical Engineering · Vol. 10, Issue 1, 2020 · pp. 30–42 Read article
-
A Novel Logic Styles used for Leakage Power Reduction in MOS Integrated Circuit
Abstract: Modified constant delay logic style and clocked logic style is defined by comparing their result. In this paper, a design technique has been proposed which reduces the power dissipation. The design and implementation of full adder and ripple carry adder with constant delay logic. The leakage power has become a serious concern in CMOS technologies that has been solved by the MCD and clocked logic style. Constant delay logic style …
Published in Journal of VLSI Design Tools and Technology · Vol. 6, Issue 1, 2016 · pp. 1–5 Read article
-
Spintronic Logic Circuits for Ultrafast Processing
Abstract: Spintronic logic has emerged as one of the most promising post-CMOS paradigms capable of addressing the speed, density, and energy challenges of deeply scaled silicon technologies. By relying on the intrinsic properties of electron spin and magnetization dynamics, spintronic devices—particularly Magnetic Tunnel Junctions (MTJs), Spin-Transfer Torque (STT), and Spin–Orbit Torque (SOT) structures—enable ultrafast, non-volatile data processing with significantly reduced energy consumption. Despite remarkable device-level advancements, circuit- level realization of high-speed, …
Published in International Journal of VLSI Circuit Design & Technology · Vol. 3, Issue 2, 2025 · pp. 35–43 Read article
-
Design of a Multipurpose Ternary Arithmetic Circuit Using CNTFET
Abstract: AbstractIn this paper, a multipurpose ternary arithmetic circuit is presented for ternary processors based on carbon nanotube field effect transistors (CNTFETs). Both addition and subtraction can be performed using same circuit’s configuration, which is the special feature of the proposed circuit. The combination of pseudo and complimentary logic structure are employed to blend the binary and ternary logic techniques. The propagation delay and power delay product are 139.5 pico second …
Published in Journal of Semiconductor Devices and Circuits · Vol. 3, Issue 1, 2016 · pp. 13–24 Read article
-
Cluster Based Sleep Transistor Approach for Low Power 6T SRAM Cell
Abstract: The demand of high density VLSI circuits has been increasing as the size of ICs is becoming small day by day. It has been seen that, to reduce active power dissipation in memory, the supply voltage reduction is necessary. Lowering the supply voltage is one of the most straightforward and effective ways to suppress the energy consumption because reducing the supply voltage could reduce the dynamic power and leakage power …
Published in Journal of VLSI Design Tools and Technology · Vol. 6, Issue 1, 2016 · pp. 41–48 Read article