Search
45 articles for “output voltage”
-
Strengthening Low Voltage Ride-Through in Wind Energy Systems: A Comparative Study of DVR and STATCOM
Abstract: This study looks at the various methods used to improve the low-voltage ride-through (LVRT) capabilities of wind turbine systems (WT) that are based on double-fed induction generators (DFIG). The Type-III WT machine, which is mostly based on DFIG, is instantly connected to the grid without the digital power interface, making the terminal voltage or reactive electricity output unmanageable. This is because the world utilizes between 20% and 25% of renewable …
Published in Journal of Power Electronics and Power Systems · Vol. 14, Issue 3, 2024 · pp. 47–62 Read article
-
Performance Comparison of Noise-Tolerant, High- Performance CMOS Domino Logic Configurations
Abstract: In high-performance VLSI chip design, domino logic configuration is often preferred over static logic due to its faster operation and smaller area footprint, especially in deep submicron (DSM) technology. However, DSM noise has become a significant challenge in domino-based circuits, leading to compromises in the reliability and signal integrity of integrated circuits (ICs). The switching threshold of domino logic, defined as the input voltage level at which the gate output …
Published in Journal of Semiconductor Devices and Circuits · Vol. 12, Issue 2, 2025 · pp. 35–50 Read article
-
An Experimental Investigation of Process Parameters for Aluminum Alloy Composites
Abstract: The objectives of this work are to develop an aluminum alloy composites and investigate machining process parameters effect on the tool wear rate for composites. The composite is enhanced using silicon carbide and graphite. The composite is made by a method called stir casting. Furthermore, it is investigated both mathematically and experimentally. This study takes trial on aluminum alloy composite to see output characteristics tool wear rate are affected by …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 185–193 Read article
-
Design and Simulation of Low-power, High-speed Effective Area Mux Based One-bit Full Adder Using CMOS Technology
Abstract: Our findings reveal a novel kind of circuit capable of performing both XOR and XNOR operations in parallel. Power dissipation and delay are both greatly reduced in the proposed circuits due to their low output capacitance as well as minimal short-circuit power dissipation. We show six new hybrid 1-bit full-adder (FA) circuits that take use of the XOR-XNOR or XOR/XNOR gates' special full-swing function. Each potential circuit layout has both …
Published in International Journal of VLSI Circuit Design & Technology · Vol. 1, Issue 1, 2023 · pp. 25–33 Read article
-
Improvement of Geometric Tolerances and Mechanical Properties of Aluminum Hybrid Metal Matrix Composites
Abstract: In the field of metal matrix composite materials, there has been a generous thrust towards the development of electrical discharge machining (EDM). In this study, stir casted aluminum hybrid metal matrix composites were successfully machined using EDM by analyzing the input process parameters namely, pulse-on time, peak current, and gap voltage using L27 orthogonal array. The ideal conditions for various output responses such as material removal rate, circularity, and radial …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1583–1592 Read article
-
Dielectric Elastomers in Actuation and Energy Applications: Material Behavior and Design Strategies
Abstract: Dielectric elastomers (DEs), a class of electroactive polymers, have attracted significant attention for their ability to undergo large, reversible deformations under electric stimulation. This unique capability makes them highly suitable for a range of actuation and energy harvesting applications, especially in the emerging fields of soft robotics, flexible electronics, artificial muscles, and sustainable power generation systems. DEs offer compelling advantages such as low weight, mechanical flexibility, high energy density, and …
Published in International Journal of Electro-Mechanics and Material Behaviour · Vol. 3, Issue 1, 2025 · pp. 13–18 Read article
-
Electric Vehicle And Charging System
Abstract: The swift expansion of Electric Vehicles (EVs) has generated a demand for smart charging structure. This project outlines the design and employment of an Electric Vehicle Charging System emphasizing power delivery, improved energy control and ease of use. The system combines power electronics, microcontroller-guided monitoring, safety apparatuses and an organized charging protocol to guarantee compatibility, with EV battery types. The suggested charger functions by transforming the AC input into a …
Published in Journal of Automobile Engineering and Applications · Vol. 12, Issue 3, 2025 · pp. 25–31 Read article
-
Layered Metal–Polymer Hybrid Laminates with Embedded Impact Sensors for Connected Automotive Panels
Abstract: The increasing demand for lightweight, intelligent, and structurally reliable automotive components has accelerated the development of multifunctional hybrid materials capable of simultaneously providing superior mechanical performance and real-time structural health monitoring. In this study, a novel layered metal-polymer hybrid laminate incorporating an embedded flexible impact sensor was developed for connected automotive panel applications. The laminate was fabricated using AA6061-T6 aluminum alloy face sheets and a thermoplastic polyurethane interlayer through hot-press …
Published in Journal of Polymer & Composites · Vol. 14, Issue 5, 2026 Read article
-
Revolutionizing EV Battery Charging: Enhancing Power Factor with Modified Bridgeless Landsman Converter
Abstract: The work focuses on the design and implementation of an innovative battery charger for electric vehicles (EVs) with a significant improvement in the power factor at the front end. The existing EV chargers often suffer from poor power factor, leading to increased losses and reduced efficiency. An altered Landsman power factor correction (PFC) converter is used in place of the traditional diode bridge rectifier (DBR) in order to solve this …
Published in Journal of Power Electronics and Power Systems · Vol. 14, Issue 2, 2024 · pp. 12–20 Read article
-
Footstep Power Generation Using Piezoelectric Materials: A Renewable Approach for Smart Infrastructure
Abstract: The rapid depletion of fossil fuels and the increasing global demand for sustainable energy have necessitated the development of decentralized energy harvesting systems. This paper presents a comprehensive study on footstep-based power generation using piezoelectric materials as a viable renewable energy solution for smart infrastructure. The proposed system converts mechanical energy generated from human locomotion into electrical energy using optimized piezoelectric transducer arrays integrated beneath floor tiles. The study covers …
Published in Trends in Electrical Engineering · Vol. 16, Issue 1, 2025 Read article
-
Design and Simulation of Low Power Allow Area High Speed Carry Save Adder using CMOS 16 nm Technology.
Abstract: In this article, we propose a novel 1-bit hybrid full adder circuit that is implemented using eighteen transistors. Simulations are done using the Mentor Graphics Tool 16nm technologies. The performances are evaluated based on their speed, average power consumption, and power-delay product. The essential components of arithmetic units including compressors, comparators, parity checkers, etc. are full adders. Thus, raising the performance of the entire adder will raise the system's performance. …
Published in International Journal of VLSI Circuit Design & Technology · Vol. 1, Issue 2, 2023 · pp. 17–28 Read article
-
Incremental Conductance Algorithm and Perturb and Observe Algorithm Reveals Key Insights into Their Comparative Analysis: A Review
Abstract: The maximum or more is a crucial aspect of PV systems to optimize energy harvesting from solar panels, which have been the focus of extensive research and implementation. This study presents a comprehensive comparative analysis of these two methods of evaluation to evaluate their performance and suitability for various operating conditions. The Perturb and Observe method, a simple and widely adopted MPPT algorithm, involves perturbing the operating point and observing …
Published in International Journal of Optical Innovations & Research · Vol. 2, Issue 2, 2024 · pp. 9–16 Read article
-
Advancements in Dual-Axis Sun Tracking Solar Panels: Integration and Impact of Weather Sensors
Abstract: In this document, the project suggests this article offers a thorough analysis of the technology, design, and control schemes of a rigid sensor-based dual-axis solar energy tracking system. The results of this inquiry will be valuable to solar energy technology scientists, engineers, and policy makers since they provide information about the most sophisticated dual-axis solar tracking system using hard sensors. Its potential to enhance solar tracking performance is also explored, …
Published in Research & Reviews : Journal of Space Science & Technology · Vol. 13, Issue 2, 2024 · pp. 11–17 Read article
-
Walking into the future: Energy Harvesting from Foot Fall
Abstract: The rapid depletion of non-renewable energy resources and the rising demand for sustainable alternatives have led to the exploration of innovative energy harvesting technologies. One such approach is harnessing the untapped mechanical energy produced by human footfalls in crowded public areas. This project presents a novel method of electricity generation using a flywheel-based mechanical system that captures and converts footstep energy into electrical energy. The system is designed to be …
Published in Journal of Alternate Energy Sources & Technologies · Vol. 17, Issue 1, 2026 · pp. 28–34 Read article
-
Design and Simulation of Full Adder-Based CMOS 4-2 Compressor using CMOS XOR-XNOR Logic
Abstract: This study utilizes the recent development of CMOS transistors to construct an energy-efficient Full adder-based CMOS 4-2 compressor. The CMOS Exclusive-OR-Exclusive-NOR component and multiplexer used in the transmission logic of the novel CMOS compressor include eight transistors. The XOR-XNOR logic style is the most efficient and effective due to its speed and reduced power consumption. Utilizing an operational supply voltage of 0.7 V and 90nm CMOS technology, the Cadence Virtuoso …
Published in Recent Trends in Electronics Communication Systems · Vol. 12, Issue 3, 2025 · pp. 1–8 Read article
-
Flying Drone Using KK Flight Controller
Abstract: This paper presents the design, development, and testing of a quadcopter drone using the KK2.1.5 flight controller, with an emphasis on stability and educational value. The KK2.1.5 controller features are inbuilt LCD screen, inbuilt programming, enabling direct configuration and tuning without the need for a computer interface, which makes it highly suitable for beginners and students. The drone is built using a modular frame architecture, which allows for easy replacement …
Published in International Journal of Advanced Control and System Engineering · Vol. 3, Issue 2, 2025 · pp. 20–25 Read article
-
Implementation of STATIC-RANDOM-ACCESS-MEMORY-Based In-Memory Computing-architecture for improving Energy Efficiency
Abstract: The in-memory-computing architecture the improvement of big data and high-performance computing. In memory-computing (IMC) as reduces the latency and power consumption of data processing. Proposed research paper static random-access memory-based IMC architecture. By completing internal write-back, NMOS transistors increase computational efficiency and eliminate the need to read the computational output right away. A 128×128 STATIC-RANDOM-ACCESS-MEMORY-IMC macro chip is designed using the 78-nm technology. The energy efficiency of 55.3TOPS/W with supply …
Published in Journal of VLSI Design Tools and Technology · Vol. 15, Issue 1, 2025 · pp. 25–35 Read article
-
Modeling and Simulation of a Grid-Connected Solar-Wind Hybrid Renewable Energy System with Controlled Inverter
Abstract: Solar and wind energy offer eco-friendly and renewable options to conventional energy sources, holding great promise for the future. This research delves into the modeling and simulation of a grid-connected solar-wind hybrid renewable energy system employing a controlled inverter. The study examines the individual photovoltaic (PV) and wind energy conversion systems and investigates their seamless integration to create a powerful hybrid generation system. To maximize energy use, the application of …
Published in Journal of Thermal Engineering and Applications · Vol. 13, Issue 1, 2026 · pp. 22–32 Read article
-
High-speed Data Converter Architectures: Latched Comparator Design & Performance Comparison
Abstract: This paper focuses on the design and optimization of latch comparators for high-speed data converter applications. The performance of different comparator architectures is compared in terms of speed, power consumption, and noise performance. The proposed latch comparator architecture uses a preamplifier to boost gain and sensitivity, and a latch to store the output signal. The latch comparator design is optimized for low power consumption and high speed, and is implemented …
Published in Journal of VLSI Design Tools and Technology · Vol. 14, Issue 1, 2024 · pp. 23–32 Read article
-
Integration of Wind and Solar Energy with Fuzzy Logic Control MPPT for Grid-Connected Hybrid Renewable Power Generation
Abstract: The utilization of renewable energy sources, such as wind and solar energy, has gained significant attention due to their eco-friendly nature and sustainability. This research paper explores the mechanisms behind wind generation and its integration with solar power, focusing on the adoption of Fuzzy Logic Control (FLC) for Maximum Power Point Tracking (MPPT) in a grid-connected hybrid renewable energy system. The paper outlines the principles of wind and solar energy …
Published in International Journal of Electrical Power and Machine Systems · Vol. 3, Issue 2, 2025 · pp. 1–19 Read article