Search
93 articles for “(EP) Epoxy Resin”
-
Effect of hybridization on mechanical Characteristics of hemp,bamboo and jute reinforced epoxy bio composites
Abstract: In the present study, hemp, jute and bamboo fibres have been reinforced with epoxy resin to develop several bio-composites (hemp/epoxy, jute/epoxy, bamboo/epoxy, hemp/jute/epoxy, hemp, bamboo, epoxy and hemp/jute/bamboo/epoxy). Their mechanical characteristics (impact strength, flexural strength, and tensile strength) have been evaluated by conducting standardized ASTM tests on the fabricated bio-composite specimens. Among these, the hybrid epoxy composite reinforced with hemp, jute, and bamboo fibers has exhibited superior tensile and impact …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 81–91 Read article
-
Effect of High-Shear Mixing on Alignment of Carbon Nanofiber/Epoxy Nanocomposites
Abstract: AbstractOne of the major technological issues limiting widespread use of epoxy polymer nanocomposites containing carbon nanofibers is processability, where the dispersion or alignment of the nanofibers is crucial to performance of the composite. Poor dispersion of the nanofibers can lead to deterioration in properties, while aligning them affords the opportunity to maximize properties in a given direction. The authors have recently investigated the effect of high-shear mixing as a potential …
Published in Journal of Polymer & Composites · Vol. 2, Issue 1, 2023 · pp. 9–18 Read article
-
FABRICATION AND COMPRESSIVE TEST ANALYSIS OF CARBON FIBRE REINFORCED NYLON
Abstract: AbstractThe aim of the paper is to study and investigate the effect of carbon fibers (T800), epoxy resin and hardener Tri Ethylene Tetra Amine (TETA) reinforced with nylon rod. There is a wrapping of carbon fiber done on the nylon rod which increases the compressive strength. It is found that compressive strength very with respect to variation of wrapping around nylon rod. The density of final material reduces as the …
Published in Trends in Opto-electro & Optical Communication · Vol. 9, Issue 3, 2019 · pp. 28–32 Read article
-
Simulation of Propeller Shaft for Composite Material
Abstract: Composites are today widely used to design the automobile components as they have outstanding specific stiffness and strength properties. Weight reduction can be primarily achieved by the introduction of better material. The conventional system uses metallic shaft, has inherent limitations like heavy weight, corrosion, flexibility problems, vibrations, which magnifies with increase in shaft diameter. Advanced composite materials offer the potential to improve propulsion shafting, by reducing weight, bearing loads, alignment …
Published in Current Trends in Signal Processing · Vol. 10, Issue 3, 2020 · pp. 16–31 Read article
-
Tensile and Flexural Strength Quantification of Basalt-Reinforced Epoxy Composites Fabricated via Vacuum-Assisted Resin Transfer Molding at Varied Fiber Volume Fractions Description
Abstract: Fiber-reinforced polymer composites have been identified to possess excellent properties that render them very suitable in the aerospace, automotive, marine and renewable energy sectors. However, for the industrially scalable vacuum-assisted resin transfer molding (VARTM) process, optimization of mechanical properties of basalt epoxy composites must be achieved systematically, which means that the effect of the fiber volume fraction (VF) on the mechanical properties of the composite needs to be quantified for …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 · pp. 43–57 Read article
-
A review of nanocomposite coatings for marine applications
Abstract: This paper reviews the performance and material characterization of nanocomposite coatings on the hydraulic pipelines of Ship A-Frame, which were corroded due to seawater exposure. Hydraulic pipe lines made of carbon steel face severe corrosion due to the highly corrosive nature of seawater with high salinity and microorganisms. The shipping industry utilizes organic and inorganic coatings to safeguard the hydraulic and seawater pipe lines of deck machines from marine pollution. …
Published in Journal of Offshore Structure and Technology · Vol. 11, Issue 1, 2024 · pp. 1–9 Read article
-
Diglycidyl Ether of Bisphenol A (DGEBA) Based Epoxy Sizing Agent Induces Surface Polarity in Carbon Fibers†
Abstract: Determination of the chemical structure and composition of the sizing agent is a challenge as its concentration is low, varying in the range from ~0.5 wt.% (for polyacrylonitrile, PAN, based carbon fibers) to ~1 wt.% (for pitch-based carbon fibers). Moreover, such a piece of knowledge is vital for designing compatible polymer matrices to prepare CFRPs for diverse applications. As a result, the sizing layer that is coated on the carbon …
Published in International Journal of Crystalline Materials · Vol. 1, Issue 2, 2024 · pp. 24–34 Read article
-
An Assessment of Interfacial Chemistry and Character of Fiber/Polymer Microcomposites
Abstract: AbstractThe interfacial chemistry and character of hygrothermally treated E-glass/epoxy microcomposite have been investigated by Fourier transform infrared spectroscope (FTIR-imaging), temperature-modulated differential scanning calorimeter (TMDSC) and scanning electron microscope (SEM) techniques. The physico-chemical interactions occurring between absorbed water molecules and the network of a tetrafunctional epoxy resin were studied by FTIR-imaging. This is used to study the mechanistic details of epoxy curing on the molecular level. Absorbance peaks of OH stretching …
Published in Journal of Polymer & Composites · Vol. 1, Issue 1, 2013 · pp. 1–5 Read article
-
Experimental Evaluation of Carbon Fiber Reinforced Epoxy Composites for Structural Applications
Abstract: Composites made of carbon fibre reinforced polymer (CFRP) are currently one of the most widely used material classes in advanced engineering applications because of their remarkable environmental resistance, dimensional stability, and strength-to-weight ratio. The vacuum bag moulding method was used in this study to create CFRP laminates with different fiber-to-resin weight ratios: 50:50, 55:45, 60:40, 65:35, and 70:30. The reinforcement phase was made of unidirectional carbon fibre fabric and the …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 401–415 Read article
-
Dynamic Mechanical Analysis of Carbon Fiber Reinforced Polymer Composites
Abstract: This study investigates the thermal decomposition and mechanical properties of Fiber-Reinforced Polymer Composites (FRPCs) using Dynamic Mechanical Analysis (DMA). The research focuses on improving the recycling and recovery process of Carbon Fiber-Reinforced Polymers (CFRPs), addressing environmental concerns regarding their disposal. By analyzing the effects of different heating rates (5°C and 10°C per minute) and atmospheric conditions (nitrogen, oxygen, and a combination of both), the study identifies optimal parameters for maximizing …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 386–393 Read article
-
Acalypha Indica Root Fibre in Polymer Composite: Mechanical Characterization
Abstract: The mechanical characteristics of Acalypha Indica root fibre reinforced epoxy resin composites, including tensile strength, tensile modulus, percentage of elongation, flexural strength, and impact strength, were studied. Composites were fabricated using epoxy glue and randomly oriented fibres of 3 mm length in varying weight ratios of 10%, 20%, 30%, and 40%. The hand layup method was followed by compression moulding to construct the composites. The study aimed to determine the …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 512–522 Read article
-
Experimental Analysis and Predictive Modeling of Mechanical Behavior in Epoxy Composites Reinforced with Waste Tyre Rubber Particles
Abstract: The disposal of end-of-life tyres poses a significant environmental and resource challenge owing to their large volumes and non-biodegradable nature. In this work, we explore the incorporation of waste tyre rubber particles (WTRP) into an epoxy resin matrix to develop sustainable polymer composites and examine their mechanical behavior both experimentally and through predictive modelling. Composites with differing epoxy: WTRP ratios (80:20, 75:25, 70:30 wt.%) and varying rubber particle mesh sizes …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1754–1765 Read article
-
Grey Relational Analysis of Cuttlefish Bone Particles–Glass Fiber Reinforced Epoxy Composites
Abstract: This research examines the mechanical characteristics, water absorption performance, and thermal stability of epoxy composites reinforced with Cuttlefish Bone Particles (CFBP) and glass fibers. Composites were fabricated with varying CFBP contents (0%, 3%, 6%, 9%, and 12%) using an epoxy resin as the matrix material and glass fiber as the primary reinforcement. The experimental results revealed that the CFBP-0 composite (neat epoxy with glass fiber) exhibited the highest tensile strength, …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 239–246 Read article
-
Synthesis and Characterization of Ether Containing Tetraglycidyl Epoxy Reinforced with Amine Functionalized Graphene Oxide (F-Go) and It’s Nanocomposites
Abstract: AbstractTGDDE matrix material along with functionalized graphene oxide (F-GO) as reinforcement was used to develop a unique skeletally modified tetra functional epoxy nanocomposites. Amine functionalization of graphene oxide nanoparticles (F-GO) on its surface was achieved by grafting 3-aminopropyltriethoxysilane (APTES) as coupling agent. The FT-IR spectrum revealed that the silane coupling agent was covalently bonded to the surface of graphene oxide nanoparticles, offering better dispersibility and compatibility with TGDDE epoxy matrix. …
Published in Journal of Polymer & Composites · Vol. 3, Issue 2, 2015 · pp. 39–51 Read article
-
Advancements In Metal-Fiber Composites for Aerospace and Defense Applications: A Comprehensive Review
Abstract: This paper provides a comprehensive review of fiber-reinforced composites, focusing specifically on the utilization of metal-fiber composites in aerospace such as metal surface preparation prior to bonding, resin selection, and detailed examination of mechanical testing and impact studies. The significance of metal surface preparation for establishing strong bonding, which is a crucial initial step in composite fabrication, is discussed. Additionally, the prevalent use of epoxy resins and their importance in …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 96–108 Read article
-
Study of Thermal Conductivity and Hardness of Coir Fiber Reinforced Epoxy Composite
Abstract: Researchers are drawn to polymer reinforced natural fibers composite for the development of new materials. The research aims to use waste fibers, specifically coir, to create polymer composite materials. Thermal conductivity and hardness of the composite results are determined under various conditions. Coir fiber is used as the reinforcement material and Coir powder is used as the filler material in the study. In the case of the matrix, the epoxy …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1576–1582 Read article
-
Development and Evaluation of Hybrid Natural Fiber Composites
Abstract: Natural fiber based polymer composites are becoming more common because they are cheap, sustainable, and operate effectively across mechanical and environmental settings. Natural fibers (NFs) like bamboo and roselle are being used to strengthen polymer composites. They are being used in textiles, medical equipment construction, and car making. People are becoming more interested in these fibers because of the unique properties. Bamboo fiber is an effective option for reinforcement in …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 908–915 Read article
-
Effects of Halloysite Nano particle Reinforcement of Epoxy Composite Using a Diglycidyl ether of bisphenol-A Prepared by Ultrasonication Casting
Abstract: This study explores a simple and operative approach for developing stronger epoxy-based composite materials by incorporating halloysite nanotubes (HNTs). The composites were made-up through hydraulic compression casting, combining ultrasonic mixing with applied pressure to produce consolidated composite sheets. HNTs were added to the epoxy resin at concentrations ranging from 1 to 5 wt.% at approximately 60°C, and the subsequent composites were examined to understand their internal structure, nanotube dispersion, and …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 Read article
-
Effect of Fillers on Electrical Conductivity of Epoxy Composites
Abstract: AbstractThis paper reports, electrical conductivity studies carried out on RT cure epoxy resin (LY556+HY951) containing three different particulate fillers graphite (Gr) a soft material, silicon carbide (SiC) a hard material and a hybrid graphite and silicon carbide (Gr-SiC). The weight fractions of three different fillers were varied from 10% to 40 wt% in steps of 10%. Increased filler fraction increases the electrical conductivity of epoxy composites for all the three …
Published in Journal of Polymer & Composites · Vol. 6, Issue 3, 2018 · pp. 25–30 Read article
-
Experimental Study on Effect of Recycled Epoxy Powder Reinforcement on Tensile Behavior of Acrylonitrile Butadiene Styrene
Abstract: Thermosetting plastic found wider application in the field of Aerospace, Aircraft, Wind Turbines, Marine and construction due to their long life, light weight and high strength. Among thermosets, epoxy is the major contributor. The world epoxy resin usage is almost 3.6 million tons in the year 2022 and it may cross 5.91 million tons by 2029. At their end of life most of it goes to land filling which leads …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 306–315 Read article