Current Trends in Signal Processing
Simulation of Propeller Shaft for Composite Material
Abstract
Composites are today widely used to design the automobile components as they have outstanding specific stiffness and strength properties. Weight reduction can be primarily achieved by the introduction of better material. The conventional system uses metallic shaft, has inherent limitations like heavy weight, corrosion, flexibility problems, vibrations, which magnifies with increase in shaft diameter. Advanced composite materials offer the potential to improve propulsion shafting, by reducing weight, bearing loads, alignment problems, flexibility, and vibration damping characteristics. The purpose of this study is to compare the shaft made by steel and various fibers. The main focus of this research is to study the use of jute fiber for making the driveshaft for vehicle. Driveshaft in vehicle is what makes any vehicle move by connecting the differential to the engine’s transmission system. Driveshaft undergoes various torsional loads during their operational life cycles. Due to fluctuating load most of the times, it fails and tends to stop power transmission. Thus, it is important to make and design this shaft as per load requirement with optimum strength to weight ration and stiffness to avoid failure. However, in this project work, an attempt was to evaluate the suitability of composite material such as fibers with epoxy resin for the purpose of automotive drive shaft application. A one-piece composite shaft was optimally analyzed using Finite Element Analysis Software with the objective of minimizing the weight of the shaft and comparative analysis for different types of fibers like carbon fiber, e-glass fiber and jute fiber. Jute fiber is one of the natural fibers with many advantages over conventional steel material and other fibers. Jute fiber reinforced composites are not used till for this particular application. Torsional, natural frequency and angular deformation analysis are performed to check the suitability of jute fiber composites for driveshaft application.Composites are today widely used to design the automobile components as they have outstanding specific stiffness and strength properties. Weight reduction can be primarily achieved by the introduction of better material. The conventional system uses metallic shaft, has inherent limitations like heavy weight, corrosion, flexibility problems, vibrations, which magnifies with increase in shaft diameter. Advanced composite materials offer the potential to improve propulsion shafting, by reducing weight, bearing loads, alignment problems, flexibility, and vibration damping characteristics. The purpose of this paper studyis to compare the shaft made by steel and various fibers. The main focus of this research is to study the use of jute fiber for making the driveshaft shaft for vehicle. Driveshaft in vehicle is what makes any vehicle move by connecting the differential to the engine’s transmission system. Driveshaft undergoes various torsional loads during their operational life cycles. Due to fluctuating load most of the times, it fails and tends to stop power transmission. Thus, it is important to make and design this shaft as per load requirement with optimum strength to weight ration [AG1] and stiffness to avoid failure. However, in this project work, an attempt will beas to evaluate the suitability of composite material such as fibers with epoxy resin for the purpose of automotive drive shaft application. A one-piece composite shaft will beas optimally analyzed using Finite Element Analysis Software with the objective of minimizing the weight of the shaft and comparative analysis for different types of fibers like carbon fiber, e-glass fiber and jute fiber. Jute fiber is one of the natural fibers with many advantages over conventional steel material and other fibers. Jute fiber reinforced composites are not used till for this particular application. Torsional, natural frequency and angular deformation analysis are performed to check the suitability of jute fiber composites for driveshaft application. [AG1]ratio?References (10)
- Montagnier O, Hochard Ch. Optimisation of Hybrid High -Modulus/High-Strength Carbon Fibre Reinforced Plastic Composite Drive Shafts. Mater Des. 2013; 46: 88–100p.
- Saeid Samiezadeh, Zouheir Fawaz, Habiba Bougherara. Biomechanical Properties of a Structurally Optimized Carbon-Fibre/Epoxy Intramedullary Nail for Femoral Shaft Fracture Fi xation. J Mech Behav Biomed Mater . 2016; 56: 87–97p.
- Misri S, Sapuan SM, Leman Z, Ishak MR. Torsional Behavior of Filament Wound Kenaf Yarn Fibre Reinforced Unsaturated Polyester Composite Hollow Shafts. Mater Des. 2014; 65: 953–960p.
- Badie MA, Mahdi E, Hamouda AMS. An Investigation into Hybrid Carbon/Glass Fiber Reinforced Epoxy Composite Automotive Drive Shaft. Mater Des. 2011; 32(3): 1485–1500p.
- Khalid YA, Mutasher SA, Sahari BB, Hamouda AMS. Bending Fatigue Behavior of Hybrid Aluminum/Composite Drive Shafts. Mater Des. 2007; 28(1): 329–334p.
- Jones Liang M. Mechanics of Composite Materials. 2nd Edn. Taylor and Francis Ltd.; 1999.
- Banuki. Mechanics of Composite Materials. New York: CRC Press; 1997.
- Damodar. Metal Matrix Composite . New York: Springer Publication; 2006.
- Tita. Investigation of Fracture in Transparent Glass Fibre Reinforced Polymer Composites Using Photo Elasticity. ASME J Eng Mater Technol. Jan 2004; 126(1): 1–7p.
- Hubertus. Material Characterization of Glass, Glass, and Hybrid -Fibre SCRIMP Panels. Livermore, CA (US): Contractor Report for Sandia National Laboratorie s; 2002. Cite this Article Pankaj Tatyarao Londhe, K.B. Waghulde, K.K. Dhande. Simulation of Propeller Shaft for Composite Material. Current Trends in Signal Processing. 2020; 10(3): 16–31p.