Search
1971 articles for “(DES)” (ranking capped at the first 2,000 matches — narrow the search to see the rest)
-
Design of 6-Bit Two-step Flash ADC for High Speed and Low Power Applications
Abstract: In this paper, 6-bit two-step Flash ADC operated at the 2 GS/s is designed, with optimized performance for frequency domain applications. To get the best performance, the coarse convertor of 2-bit and the fine convertor of 4-bit are chosen. The comparator design is done with optimum power and area with two power supplies. Intermediate state accuracy increased by thermometer coded current steering DAC. The DNL and INL specifications are chosen …
Published in Journal of Electronic Design Technology · Vol. 3, Issue 1-3, 2012 · pp. 29–39 Read article
-
Design and Analysis of Bootstrap Sample and Hold Circuit
Abstract: This paper describes the design and implementation of open-loop sample and hold-circuit using bootstrap technique, which can be used as front end sampling circuit for high-speed analog-to-digital converters. Different design criteria, viz., speed, power, resolution, linearity, noise and harmonic analysis have been dealt with. Both theoretical analysis and simulation results are carried out. The bootstrap circuit is designed and then compared in a 0.18 and 0.35 μm CMOS process. It …
Published in Journal of Electronic Design Technology · Vol. 5, Issue 3, 2014 · pp. 7–14 Read article
-
UNCERTAINTY OF PILE DESIGN CAPACITY IN GYPSEOUS SAND SOILS
Abstract: Uncertainty of the design is a problem comes out due to the alteration of the soil properties. Depended on the available geotechnical soil properties of Al Najaf city, a study program is prepared to investigate the effect of the alteration of some soil properties, such as unit weight and angle of internal friction, on the design bearing capacity of a bored pile. The soil of the city is suffering from …
Published in Journal of Geotechnical Engineering · Vol. 5, Issue 3, 2018 · pp. 24–30 Read article
-
An Approach for Discrete-Time Systems Design Using MPSM Continued Fraction Expansion Technique
Abstract: AbstractThis paper presents a new method for the design of the high-order discrete-time systems to overcome the limitations and drawbacks of some of the existing methods. It uses the Multi Point Squared-Magnitude Continued Fraction Expansion (MPSMCFE) and factorization technique for obtaining both denominator and numerator of the reduced order models. The method is extended for the design of high order systems using the reduced order model in place of original …
Published in Journal of Instrumentation Technology & Innovations · Vol. 7, Issue 3, 2017 · pp. 11–15 Read article
-
Design and Analysis of a Lower Control Arm in Car by Finite Element Analysis Approach
Abstract: AbstractSuspension system is the most important part in any vehicle. It directly affects the human safety as well as performance. The lower control arm is a wishbone-shaped metal strut that attaches to the wheel assembly. Structural optimization techniques under static load conditions have been widely used in automobile industry for lightweight vehicle to increase its performance level. This study deals with finite element analysis of the lower control arm of …
Published in Journal of Instrumentation Technology & Innovations · Vol. 8, Issue 2, 2018 · pp. 17–24 Read article
-
Design & Development a SPM for cutting operation: A case study on power switch assembly
Abstract: Automation is used to improve the productivity in majority of the industries. It helps in reducing the human intervention and improves a quality lot. Assembly process along with the manufacturing of each part needs to be studied, to automate the desire manufacturing processes. Here a case of power switch is investigated and analysis is carried out in terms of the automation strategy. Each process is analyzed by parameters like efficiency, …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 2, 2018 · pp. 7–17 Read article
-
Design of Pressure Vessel as Per ASME Standard and its Thickness Optimization
Abstract: The main aim of that paper is design of pressure vessel as a storage tank. Design and calculation considering as per ASME (American Society of Mechanical Engineering) standard code. Internal design pressure of vessel 3.6 MPa that pressure more than 100 psi pressure so all calculation considering ASME section VIII, division 2. Vessel internal radii 650 mm and calculated thickness 22 mm. analysis of vessel operating pressure 2 MPa at …
Published in Journal of Mechatronics and Automation · Vol. 6, Issue 1, 2019 · pp. 23–30 Read article
-
Design and Implementation of Low Power Priority Encoder
Abstract: Nowadays, low-power devices are widely used in VLSI design technology because they can reduce power consumption and power dissipation. To achieve this, various low-power techniques are utilized to minimize device power losses. This project focuses on analyzing the performance of priority encoders in different low-power technologies for Flash Type ADC. Moreover, the power consumption of these technologies is compared with the conventional CMOS design. Each of these techniques offers distinct …
Published in Journal of Microcontroller Engineering and Applications · Vol. 10, Issue 2, 2023 · pp. 1–14 Read article
-
Analysis and Design of Microstrip Antenna for Applications in Energy Harvesting
Abstract: AbstractThis paper focuses on design and analysis of wide band antenna for the use of energy harvesting. The design parameter for achieving optimal operation of the antenna is also analyzed. The presented antenna design has been simulated by IE3D software which is suitable for wide band applications at resonant frequency 3.23 and 4.25 GHz.Keywords: Wireless communication, LC filter, RF power, Schottky diodeCite this ArticleHira Sultan, Neha Sen, Vinod Kumar Singh, …
Published in Journal of Microwave Engineering and Technologies · Vol. 4, Issue 3, 2017 · pp. 1–4 Read article
-
Analysis and Design of Coaxial Fed Microstrip Antenna on Multilayer substrate at Terahertz Frequency
Abstract: AbstractThe paper presents the performance of an antenna on a three-layered substrate material analyzed to enhance the electrical parameters such as bandwidth and gain of a microstrip antenna. A regular rectangular microstrip antenna design has been updated to a planar parabolic horn design for improving bandwidth to up to 30 times provided by a rectangular patch. The design has been simulated at 0.6 THz resonant frequency using Keysight’s ADS (Advanced …
Published in Journal of Microwave Engineering and Technologies · Vol. 4, Issue 3, 2017 · pp. 11–14 Read article
-
U-Shaped Antenna Design for 5G High Frequency Band
Abstract: Designing small antennas for 5G millimeter wave bands is an emerging research subject in the wireless communication age. This research paper describes the design, simulation, and measurement of a micro-strip patch antenna operating at high frequency, 38 GHz. The substrate material used is FR4 proxy due to its easy availability and cost with the dielectric constant 3.8 to 4.6. The analysis and simulation are done on Ansys HFSS Software. The …
Published in Journal of Microwave Engineering and Technologies · Vol. 10, Issue 3, 2023 · pp. 31–40 Read article
-
Reduce Timing in Physical Design
Abstract: AbstractThe physical design flow consists of producing a production worthily from a gate level net list subject set of constraints. Here, focuses on the reduce the timing from floor plan to routing stage. Because performance of a chip depend on the timing. Mainly in routing stage manually adding the buffers and upsizing the drive strength in violating the time paths. It also surveys some physical design flows. The outlines a …
Published in Journal of Microelectronics and Solid State Devices · Vol. 6, Issue 3, 2019 · pp. 28–36 Read article
-
A Survey: A Low EMI Approach to Electronic Circuit Design
Abstract: This paper describes techniques to meet national and International standards in the area of electromagnetic interference (EMI) which are becoming very important for users and equipment manufacturers of electrical/electronic equipment. EMI sources are identified & classified into either natural or manmade. Normal sources of EMI are further classified as terrestrial, emanating on or near the Earth’s surface or non terrestrial, emanating from cosmic or solar bodies. Techniques to reduce EMI …
Published in Journal of Power Electronics and Power Systems · Vol. 3, Issue 1, 2013 · pp. 1–4 Read article
-
Design and Simulation of Discrete Time Optimal Speed Control for an Induction Motor Taking Core Loss and Stray Load Losses into Account
Abstract: Generally, the core loss and stray load loss are neglected in the mathematical model of induction motor (IM) to design the decoupling torque and flux control strategy. In order to precisely control the torque and flux, core loss and stray load loss, which are generally neglected, should be considered in the mathematical model of IM to design the controller. Some of literatures have shown how the detuning can be done …
Published in Journal of Power Electronics and Power Systems · Vol. 4, Issue 3, 2014 · pp. 46–56 Read article
-
Revamp of Feed Preheat Network Using Aspen Hysys in a Kero Hydro-Desulphurization Unit
Abstract: The paper is based on the revamp of feed preheat network in a Kero hydro-desulphurization unit. This revamp is beneficial as it does not require additional equipment to raise the feed temperature. Desulphurization of crude is a catalytic process used in oil and gas refining industry to remove sulphur content from refined petroleum products. Previously, feed was charged from the crude distillation unit at 103°C. Due to envisaged changes, the …
Published in Journal of Petroleum Engineering & Technology · Vol. 7, Issue 2, 2017 · pp. 29–38 Read article
-
Design and Structural Analysis of Ground Electronic Package
Abstract: Electronic packaging (EP) is widely used for support and enclosure or housing of electronic component. This paper includes design of EP and comparisons of analytic and static structural analysis for deformation of EP. Design of EP is carried by commercial software PTC Creo Parametric 2.0. It consists of five main parts and some other additional parts and to run the analysis. The design includes mounting of electronic circuits; improving testing …
Published in Journal of Production Research & Management · Vol. 7, Issue 2, 2017 · pp. 8–16 Read article
-
Study and Analysis on Multi-gate MOSFET Design
Abstract: AbstractMulti-gate MOSFET is the emerging technology that is used in the area of low-power VLSI design. Multi-gate devices provide much better advantages over conventional MOSFET. As less power dissipation, decrease size, and more operational value could be obtained. Multi-gate MOSFET devices also reduce cost of production. Thus, design of electronics devices based on multi-gate technology is beneficial in today’s requirement. Basic MOSFET due to its reduction in size shows short …
Published in Journal of Semiconductor Devices and Circuits · Vol. 7, Issue 1, 2020 · pp. 1–7 Read article
-
Design and Performance of Semiconductor-Biosensor
Abstract: In this work, a high electron mobility transistor (HEMT) based biosensor is designed to detect the virus-protein. In this work, all the simulation-studies are carried out in the SILVACO-ATLAS physical simulator using the following models: Shockley Read Hall (SRH), band gap narrowing, Auger recombination, and Fermi Dirac statistics. Newton trap numerical solver is used in the device simulation. Conduction band engineering of the biosensor is studied. DC and RF properties …
Published in Journal of Semiconductor Devices and Circuits · Vol. 8, Issue 2, 2021 · pp. 1–13 Read article
-
Economical Design of Stiffened Plate using FEM
Abstract: This paper presents the economical design of stiffened plate subjected to transverse load. The model of stiffened plate is developed using ANSYS APDL 14.0 for the finite element analysis and design. At first, a convergence study is carried out to arrest the optimum mesh size for discretizing the plate. The maximum deflection of plate with and without stiffeners subjected to point and uniformly distributed load for both fixed and simply …
Published in Journal of Structural Engineering and Management · Vol. 4, Issue 2, 2017 · pp. 50–57 Read article
-
ANALYSIS AND DESIGN OF R.C.C. BRIDGE
Abstract: The thickness of pier is found taking width of deck slab variable, width of girder, depth of girder variable. The thickness of any structure gives flexural rigidity against bending. Span of girder also taken variable. More bending is taken when more loads on the structure & flexural rigidity mainly depends upon thickness of the structure. The design and analysis of R.C.C. bridges involve careful consideration of various factors, including the …
Published in Journal of Structural Engineering and Management · Vol. 10, Issue 1, 2023 · pp. 41–45 Read article