Search
744 articles for “Densities”
-
Performance Analysis and Emission Study of a C.I. Engine using Butanol, Biodiesel and Diesel Blends
Abstract: Biodiesel, which has been projected as an alternative to diesel fuel, can be made an attractive and viable substitute by use of a non-glyceride type of readily available, renewable and economic resources like acid oil. The production and consumption of biodiesel will increase in future due to ecofriendly, and possibility of use of existing engines of a motor vehicle without the need for major adjustments. Biodiesel and diesel fuel are …
Published in Journal of Experimental & Applied Mechanics · Vol. 9, Issue 2, 2018 · pp. 17–22 Read article
-
Characterization of Aluminum Metal-Matrix Composite with SiC and B4C Reinforcement with Different Weight Percentage
Abstract: Metal Matrix Composites (MMCs) have been prepared by compo casting method. The effect of matrix material on the wettability/compatibility of refinement with matrix is studied. Silicon and boron ceramic particles were used as reinforcement in aluminum matrices. The study of density, micro-hardness and the tensile strength has been done in order to characterize the same. It is found that Al-SiC MMC shows an increase in density with increasing weight percentage …
Published in Journal of Experimental & Applied Mechanics · Vol. 6, Issue 1, 2015 · pp. 1–6 Read article
-
Design and Analysis of Aerodynamics on Wind Turbine
Abstract: The design and analysis of aerodynamics on a horizontal axis wind turbine rotor blade are explained in this research. A method for selecting materials for wind turbine design is described, followed by the design of the solid works. . The science and study of the physical rules that control the behaviour of objects in airflows, as well as the forces that these airflows produce, is known as aerodynamics. This article …
Published in Journal of Experimental & Applied Mechanics · Vol. 13, Issue 2, 2022 · pp. 1–5 Read article
-
Concrete Compressive Stress-Induced Crack Analysis and the Main Causes of Concrete Cracks in Construction
Abstract: The findings of experimental investigations into the micromechanical behaviour of concrete under various loading scenarios are presented in this work. Concrete specimens with normal and high strengths were examined under uniaxial compression in constrained spaces. Injection of a low melting point alloy was done into the concrete specimens' pores and fissures. To preserve the load-induced stress microcracks and the pictures from the cross sections of the concrete specimens photographed by …
Published in Journal of Experimental & Applied Mechanics · Vol. 13, Issue 2, 2022 · pp. 11–15 Read article
-
Optimum Circumscribing Circle Division Method for Getting Maximum Fill Factor in Transformer Core
Abstract: As far as the optimum design of transformer is concerned, researchers generally concentrate on minimizing cost, no load and load losses etc. by choosing K-factor, Flux density, Current density etc. as design variables. But, the design of core has remained an unexplored area. Transformer manufacturing industry uses traditional technique to find out the core design dimensions. However, in that method, the fill factor for the desired number of steps is …
Published in Journal of Electronic Design Technology · Vol. 6, Issue 2, 2015 · pp. 13–17 Read article
-
A Comparative Study on Carbon Nanotube MOSFET, Silicon Nanowire MOSFET and Single Gate MOSFET
Abstract: Among many of the concerns for the researchers in nano-electronics, Single Gate MOSFET, Silicon Nanowire MOSFET and Carbon Nanotube MOSFET were very popular three. All of them are different in their structures and performance. This paper is focused on the comparison of their characteristics in terms of Current- voltage relations, Mobility charge density and Quantum capacitance. ‘FETToy’ in ‘nanohub’ was used to simulate the predefined models in room temperature. Drain …
Published in Journal of Electronic Design Technology · Vol. 6, Issue 2, 2015 · pp. 7–12 Read article
-
Landslide Risk Assessment in Kodagu District, Karnataka: A Case Study
Abstract: AbstractIn this study, an attempt has been made to assess the landslide risk zones using a GIS based weighted linear overlay method with Satty’s analytical hierarchical process to maintain consistency for assigning rank and weight for following factors includes geology, geomorphology, rainfall, soil, road density, drainage density, and topographic triggering factors such as slope and aspects are taken as input for assessment of landslide risk.Thus the technique used in landslide …
Published in Journal of Geotechnical Engineering · Vol. 4, Issue 3, 2017 · pp. 19–34 Read article
-
Development of a Mathematical Model for Assessment of Total Dissolved Salts
Abstract: The main purpose of this research is deriving a new equation which can be used to find the total dissolved salts (TDS) in the soil. This equation enables us to find the total dissolved salts (TDS) by finding density of the saline solution resulting from dissolving the soil in distilled water. This equation shows very good results. So, in this research a new method was proposed to find the total …
Published in Journal of Geotechnical Engineering · Vol. 3, Issue 1, 2016 · pp. 20–32 Read article
-
Identification of Accident Hot Spots at Different Roads of Midnapore Municipality Area: A Geoinformatic Approach
Abstract: Road traffic injuries (RTIs) are a huge public health and development problem, killing almost 1.2 million people a year and injuring or disabling almost 20 to 50 million or more. Both WHO and World Bank data show that without appropriate action these injuries will rise dramatically by the year 2020, particularly in rapidly-motorizing countries. The study identifies the volatile traffic areas where road accidents are almost regular events and assess …
Published in Journal of Geotechnical Engineering · Vol. 1, Issue 1, 2014 · pp. 20–38 Read article
-
Dynamic Behavior of Coal Ash
Abstract: Coal ash is deposited in large quantities in the ash pond. It is used as structural fill and for dyke construction. The behavior of ash under dynamic conditions is not well investigated. The present work attempts to quantify some of the parameters, which influences the dynamic stability especially liquefaction potential of coal ash. Several investigations conducted on coal ash suggest that ash fills have low SPT value. This supports the …
Published in Journal of Geotechnical Engineering · Vol. 1, Issue 2, 2014 · pp. 7–11 Read article
-
Role of Cement and Fly Ash in Soil Stabilization
Abstract: Soil stabilization changes the engineering properties of soil and produces strength and stability. Use of industrial wastes and manufactured materials in soil stabilization can be cost effective and environmental friendly. As there is a growth of habitations surrounding the PSIT campus, therefore, soil samples collected from this area were analyzed for its plasticity index properties. It was found that soils of this area come under low plastic category. Hence, the …
Published in Journal of Geotechnical Engineering · Vol. 7, Issue 3, 2020 · pp. 1–8 Read article
-
Economic Importance of Laterite Deposit in Oke-Oyi Area, Ilorin, Nigeria
Abstract: Two soil samples A and B were taken from Oke-Oyi, Kwara state, North Central, Nigeria. The water content of the samples are 5.8% and 6.5 for sample A and B respectively. This shows the variability in water table in the area. The specific gravities values are 2.7 and 2.78 for samples A and B, this is an indicator of inorganic soil. Grain size analysis show the laterite to be sandy …
Published in Journal of Geotechnical Engineering · Vol. 10, Issue 1, 2023 · pp. 33–37 Read article
-
Impact analysis of CuSCN in Perovskite (CH3NH3PbI3) Solar Cell as Hole Transport Layer
Abstract: The comprehensive modelling and numerical simulation of perovskite solar cell’s were carried out utilizing perovskite materials such “methyl ammonium lead iodide (MAPbI3, MA= CH3NH3)” with the help of SCAPS tools and measured the measurements like "open-circuit voltage (Voc), fill factor (FF), power conversion efficiency (PCE), and short-circuit current density (Jsc) of the MAPbI3 material used as active layer, respectively.” In the modelled structure of the perovskite solar (Fig 1 as …
Published in Journal of Microcontroller Engineering and Applications · Vol. 10, Issue 1, 2023 · pp. 1–7 Read article
-
Power-Efficient Design Strategies for Static Random Access Memory with Memory Blocks: A Review
Abstract: For many years, CMOS technology has been able to achieve high integration density and great performance by scaling down its feature size and threshold voltage. Power consumption has been a major concern in VLSI design due to the ongoing drop in aspect ratio and the related improvements in chip density and operation frequency. SRAM is a type of random-access memory in which an interruption in power causes data loss. For …
Published in Journal of Microcontroller Engineering and Applications · Vol. 10, Issue 3, 2023 · pp. 23–32 Read article
-
Overlapped Multipass Laser Transformation Hardening of Ti-6Al-4V Titanium Alloy Using Continuous Wave Rectangular Beam
Abstract: Overlapped multitrack laser transformation hardening (OMLTH) of Ti-6Al-4V titanium alloy of Grade 5 of 2 mm thickness sheet has been carried out using 2 kW Nd:YAG laser source with a CW rectangular beam of size 1×14 mm2. The present research article intended to provide a profound understanding of the multipass laser hardening process of TI-6Al-4V titanium alloy, and to investigate the effect of rectangular laser beam process parameters i.e., the …
Published in Journal of Materials & Metallurgical Engineering · Vol. 7, Issue 3, 2017 · pp. 35–42 Read article
-
Wear Characteristics of Aluminium-Graphite Composites Produced by Stir Casting Technique
Abstract: Metal matrix composites (MMCs) are finding more applications due to their significantly improved properties such as high specific strength, high specific modulus, good damping capacity and good wear resistance compared to unreinforced alloys. In recent years, there has been an increasing interest in composites containing low density and low cost reinforcements. Graphite is one of the most suitable and low density reinforcement available for making light-weight and wear resistant parts …
Published in Journal of Materials & Metallurgical Engineering · Vol. 4, Issue 3, 2014 · pp. 13–20 Read article
-
An Overview on Use of Plastic Waste as Road Construction Material
Abstract: The usage of plastic in our environment is expanding day by day due to rising population urbanization, evolution, activities, and changing in life manner. This waste plastic is spreading mostly on the land. This waste plastic is becoming hard job to decompose due to its non-biodegradable property. Eventually, plastics are not decomposed scientifically and potential to create soil, air, and marine pollution as well as water pollution. Therefore, the waste …
Published in Journal of Materials & Metallurgical Engineering · Vol. 12, Issue 1, 2022 · pp. 59–66 Read article
-
Design conceptualization and computational analysis of cryogenic engine nozzle -ABYOM
Abstract: The main purpose of this paper is to design a cryogenic engine nozzle with specified dimensions using CATIA V5 software and analyze the nozzle using ANSYS software. The realizable k-ε viscous model was used for calculation and the Hydrogen (H2) had retained as an ideal gas. The CFD simulations were done on the nozzle to find the pressure, density, velocity, and temperature. In the graph, there are 500 points streamlined …
Published in Journal of Materials & Metallurgical Engineering · Vol. 12, Issue 2, 2022 · pp. 14–23 Read article
-
The advanced bioceramics production using process of vibroturbulization
Abstract: Currently, bioceramics are widely used in medicine as dental and bone implants. Surgical bioceramics are used regularly. Joint replacements are usually coated with bioceramics materials to reduce wear and tear and inflammation. Pacemakers, kidney dialysis equipment, and respirators are more instances of bioceramics being used in the medical field. The production process of bioceramics consists of the following four main steps: preparation of powder with a grain size of not …
Published in Journal of Materials & Metallurgical Engineering · Vol. 12, Issue 2, 2022 · pp. 10–13 Read article
-
Built in Self Repair for Embedded Memories: A Survey
Abstract: Memory is a significant part of every single computing system. In SOC (System-on-a-chip), 90 to 92% of the total chip zone is enclosed by embedded memories (ITRS 2009) and that means memory density is higher than the logic density. Consequently testing and diagnosis of memories are imperative issues in the SOCs. Revenue of memory is pretentious by the accountabilities present in memory which also distresses the yield of SOC. Built …
Published in Journal of Microelectronics and Solid State Devices · Vol. 2, Issue 1, 2015 · pp. 18–22 Read article