Search
17 articles for “volumetric properties”
-
Volumetric Properties of PEG-400 in FS-13 Diluent for 293.15 K to 343.15 K at 0.1 MPa
Abstract: PEG-400 in FS-13 solvent was proposed for strontium extraction from spent fuel solution in back end of nuclear fuel cycles. Densities and viscosities of solutions of PEG-400 and FS-13 were not available in literature. Densities and viscosities of binary mixture of extractant PEG-400 in FS-13 diluent was measured from 293.15 to 323.15 K. The excess molar volume (VE) and excess Gibb’s free energy of activation (DGE) was evaluated from density …
Published in Journal of Nuclear Engineering & Technology · Vol. 5, Issue 3, 2015 · pp. 1–5 Read article
-
Influence of Polymer Additives on Physical Properties of Asphalt Concrete under Marshal, Flexure and Compressive Stresses
Abstract: AbstractThe polymer modified asphalt cement is used today to reduce early pavement distress and extend service life by enhancing adhesion, cohesion, and elasticity. This work studies the impact of polymer additives (SBS, LDPE, and rubber) to asphalt cement on the physical properties of asphalt concrete subjected to compression and flexure stresses, and Marshal volumetric properties. Asphalt concrete cylindrical specimens of 101.6 mm diameter and 127 mm height for compressive strength …
Published in Trends in Transport Engineering and Applications · Vol. 4, Issue 3, 2017 · pp. 8–17 Read article
-
Influence of ZycoTherm Dosage on Polymer Modified Bitumen and Marshall Performance of Hydrated Lime Incorporated Warm Mix Bituminous Concrete
Abstract: This study examines the effect of ZycoTherm on PMB 76-10 binder characteristics and the performance of PMB-based Bituminous Concrete (BC) Grade-II prepared at reduced mixing temperatures, with and without hydrated lime. PMB 76-10 was modified with ZycoTherm at dosages of 0.05%, 0.10%, 0.15%, and 0.20% by weight of binder and evaluated using conventional and residue-based tests. Increasing ZycoTherm dosage decreased penetration, while softening point, flash point, and elastic recovery increased, …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 256–267 Read article
-
Performance Evaluation of Modified Cold Mix Asphalt by Some Waste Materials
Abstract: The aim of study is to evaluate modified CMA volumetric, mechanical and durability properties by some waste materials. Previous studies described that the mechanical properties of CMA are shown to be influenced by different factors including base bitumen grade, porosity of the mix, curing time and additives. The current research is designed to use the waste and by-product materials as filler to enhance the conventional CMA early age strength. Hence, …
Published in Trends in Transport Engineering and Applications · Vol. 3, Issue 3, 2016 · pp. 33–53 Read article
-
Enhanced Thermal Stability and Thermophysical Properties of High Density Polyethylene Based Polymer Composite Synthesized Through Compression Moulding Route
Abstract: Polymer composite materials attract researchers as polymers can be filled with different fillers to get desired properties. Thermophysical properties of HDPE-silicon composite is reported in the present study. HDPE-Si composite was synthesized by hot compression and molding technique for different silicon volumetric ratio. Thermal conductivity as well as thermal diffusivity was found to be enhanced significantly on increasing the filler volumetric ratio. Thermal conductivity value for 20 volume % composite …
Published in Journal of Polymer & Composites · Vol. 11, Issue 5, 2023 · pp. 1–16 Read article
-
Comparative Experimental Investigation of Infill Pattern and Infill Density on Fused Deposition Modeling (FDM) Process Characteristics of Polylactic Acid (PLA)
Abstract: Additive manufacturing is the potential and emerging technology widely being used to produce quality products with complicated profiles and customized features. Fused Deposition Modelling (FDM) process, a type of additive manufacturing technology using filament made of thermoplastic which is melted and subsequently extruded through nozzle. The main input process parameters of FDM are wall thickness, infill density, layer height, bed temperature, layer thickness, infill pattern, nozzle temperature etc. In this …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 335–345 Read article
-
Mechanism of Microwave: Material Interaction and Its Effect on Material Properties
Abstract: Application of microwave energy for materials processing is emerging as a novel and innovative technology with many advantages over conventional processing, such as reduction in processing time resulting into energy and cost savings, providing finer microstructures, leading to improved mechanical properties and eco-friendliness etc. Microwaves are electromagnetic waves with wavelengths ranging from 1 m to 1 mm, which correspond to frequencies between 0.3 and 300 GHz. Microwave heating is a …
Published in Nano Trends – A Journal of Nano Technology & Its Applications · Vol. 18, Issue 2, 2016 · pp. 11–14 Read article
-
Hydrogen as an Alternative Fuel for Internal Combustion Engines
Abstract: This paper critically reviews articles on hydrogen as an alternative fuel in an internal combustion engines (ICE). Emphasis is given to the properties of hydrogen fuel with respect to engine performance while developing explicit comparison with a typical gasoline fuel (iso-octane). Calculations were made which demonstrated lower volumetric efficiency of a –ICE as result of its 30% relative occupancy in the combustion chamber. Detailed combustion chemistry and consequent dependence of …
Published in Journal of Alternate Energy Sources & Technologies · Vol. 5, Issue 2, 2014 · pp. 50–57 Read article
-
Volumetric and Viscometric Studies of Molecular Interactions in Binary Mixtures of Butylamine and Iso-butylamine with 1-decanol at Different Temperatures
Abstract: Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 The increasing use of alkylamine and alkanol in various chemical and industrial processes encouraged investigation on the thermodynamic and transporting properties of alkylamine, alkanol and their mixtures for obtaining extensive information. Excess molar volume (VE), deviation in viscosity (Dh) and excess Gibbs free energy of activation of viscous flow (G*E) have been calculated from measured densities and viscosities of pure butylamine …
Published in Journal of Modern Chemistry & Chemical Technology · Vol. 2, Issue 1, 2011 · pp. 24–35 Read article
-
Microwave Curing of Glass-Epoxy Composites Using Silica Based Moulds
Abstract: AbstractFor polymer composite product manufacture, curing of the fibre reinforced polymers (FRP) is a critical step in achieving desired mechanical properties. The conventional cure processes involve thermal curing in hot air ovens and autoclaves where the cure process is time and energy intensive. In this context, microwave curing is one of the most promising processing methods since it results in substantially reducing cure cycle time, energy requirements and operational costs …
Published in Journal of Polymer & Composites · Vol. 3, Issue 2, 2015 · pp. 52–57 Read article
-
Impact of various Fibers on the Mechanical and Durability Performance of Fibre-Reinforced Concrete with SBR latex
Abstract: Recent years included a proliferation of research efforts focused on fibre reinforced concrete (FRC), an innovation that perceives extensive application in the construction industry. FRC's enhanced mechanical properties ahead of conventional concrete have broadened its significance recently. Natural fibers have been produced in response to expanding environmental deterioration in recent years, and research is currently continuing with the goal of utilizing them in the construction field. This study explores the …
Published in Journal of Polymer & Composites · Vol. 12, Issue 2, 2024 · pp. 26–40 Read article
-
Development of Refractory Synthesized from Waste Ceramic Fiber and Chamotte
Abstract: Research on refractory materials is always essential in thermal engineering to ensure both heat savings and environmental protection. Raw materials used initially have a great influence on the production process and product properties. In addition, the refractory products are tested under conditions of high temperature and varying intensity, such as tests of thermal shock resistance. In this study, new refractory composites were prepared by mixing waste ceramic fibers with chamotte …
Published in Journal of Polymer & Composites · Vol. 8, Issue 2, 2020 · pp. 101–109 Read article
-
Acoustical and Thermodynamical Studies of L- Glycine in Buffer Solution of Different pH at 298.15 K
Abstract: The volumetric, viscometric, and acoustical studies are used to investigate the exchange of L-Glycine in a buffer solvent system of different pH at 298.15K within a concentration range of 0.02 to 0.10 molal. L-glycine, being the simplest amino acid, serves as an important model compound for understanding molecular exchanges in biological systems. The effect of pH on the physicochemical properties of amino acid solutions is of considerable significance, as it …
Published in Journal of Modern Chemistry & Chemical Technology · Vol. 17, Issue 2, 2026 · pp. 48–58 Read article
-
Additive Manufacturing of Polymer-Based Advanced Composites: Mechanical Properties and Performance Evaluation
Abstract: Fabrication of large-scale and geometrically complex polymer-based advanced composites via fused deposition modelling (FDM) has been shown to be a promising technology for the production of such materials, however there are challenges in using short carbon fibre-reinforced polylactic acid (CF-PLA) which include obtaining high mechanical performance and maintaining dimensional accuracy with dynamic robot motion and complex interactions occurring between process parameters. The conventional approaches are mostly static feed rates or …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1326–1335 Read article
-
Influence of Supplementary Cementitious Materials on Chemical Shrinkage in Cement
Abstract: Chemical shrinkage is the volume reduction observed in cement during early hydration due to chemical reactions, which critically influences the internal stresses, cracking tendencies, and durability of cementitious system. Present study is focused on effect of supplementary cementitious material (SCM) on chemical shrinkage. Dilatometry method is used to assess the impacts of SCMs on chemical shrinkage, in this this study. The research incorporates experiments with laboratory-synthesized cement and three SCMs—fly …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 98–107 Read article
-
Analysis of Machining Parameters in Wire EDM with Aluminum Alloy Using PCA and TOPSIS Approach
Abstract: Although the efficiency of traditional cutting processes is inadequate by the mechanical properties of the processed material and the intricacy of the work piece geometry, electrical discharge machining (EDM) being a thermal erosion process, is subject to no such limitations. This paper summaries the suitable use of Taguchi’s L27 orthogonal array which takes 27 experimental runs to develop a mathematical model for correlating the interactive and higher order impacts of …
Published in Journal of Mechatronics and Automation · Vol. 4, Issue 2, 2017 · pp. 1–11 Read article
-
AEROGELS – A VALUE ADDITION TO HARVEST SOLAR ENERGY
Abstract: Aerogels are a class of synthetic porous ultralight material that was created in 1930 and derived from a gel, in which the liquid component has been replaced with a gas without collapsing the gel structure by freeze-drying. It is made of silica, but carbon, iron oxide, gold, copper, polymer etc. can also be used. During freeze drying the liquid in the gel is slowly dried off without collapsing the solid …
Published in Journal of Thermal Engineering and Applications · Vol. 9, Issue 2, 2022 · pp. 23–39 Read article