Search
34 articles for “Latent Heat”
-
CFD Analysis: Double Pipe Heat Exchanger, Latent Heat Storage, and BIM-CFD Integration
Abstract: This is a review work covering four research papers. Heat exchangers transport thermal energy across fluids; research in SolidWorks 2014 compared flow simulation to the effectiveness-NTU approach. Slow PCM charging/discharging is a global concern in latent heat storage; research on the influence of flow rate and temperature on melting and solidification durations discovered efficiency in a triple tube heat exchanger design. Advances in computational fluid dynamics for forecasting separated flows …
Published in International Journal of Electrical Machine Analysis and Design · Vol. 2, Issue 2, 2024 · pp. 19–24 Read article
-
Evolution of Empirical Equations for Prediction of Melting Point and Latent Heat of Alkanes
Abstract: Alkanes and paraffins are well recognized phase change materials (PCMs) for low and medium range temperature thermal energy storage applications. Melting point and latent heat are two crucial parameters for any PCM for its use in any thermal storage application. The values of these parameters are normally measured by expensive and time consuming measuring devices.In this paper, three empirical equations are presented to predict the melting point and latent heat …
Published in Journal of Modern Chemistry & Chemical Technology · Vol. 7, Issue 3, 2016 · pp. 8–11 Read article
-
Comprehensive Thermal and Environmental Investigation of An Enhanced Evacuated Tube Solar Water Heater with Wavy Tape and Latent Heat Storage
Abstract: Evacuated tube solar collectors (ETSCs) are widely used for thermal energy applications; however, enhancing their thermal and exergetic efficiency remains a challenge. This study investigates performance enhancements through structural and material alterations. Four ETSC cases were tested experimentally, case-1: a standard ETSC, case-2: Wavy tape (WT) inserted ETSC, case-3: Phase change material (PCM) integrated ETSC, and case-4: Dual-Enhanced ETSC (PCM + WT). A binary eutectic PCM was utilized for latent …
Published in Journal of Refrigeration, Air conditioning, Heating and ventilation · Vol. 12, Issue 2, 2025 · pp. 1–16 Read article
-
Experimental investigation of solar sill by incorporating sensible and latent heat storage materials
Abstract: The main obstacle to human life in the modern age was the lack of access to and improper distribution of potable water on earth. Despite the fact that demand for potable water is skyrocketing due to population growth and industrial exploitation, supply levels are essentially steady. Due to its simplicity in construction, ease of maintenance, techno-economic advantages, and eco-friendliness, solar is still regarded as one of the best possible options …
Published in Journal of Refrigeration, Air conditioning, Heating and ventilation · Vol. 10, Issue 1, 2023 · pp. 7–21 Read article
-
Study on Solar Water Heater with Thermal Energy Storage System
Abstract: AbstractRenewable power supplies are progressively gaining increasing importance in all the nations. Specially, solar electricity, being non-polluting and inexhaustible, has obtained extensive interest among scientists and engineers. Although, there are many advantages, an essential factor is that solar power is time structured power source with an intermittent individual. Consequently, some form of thermal power storage (TES) is necessary for the only usage of this energy supply. Thermal energy can be …
Published in Journal of Nuclear Engineering & Technology · Vol. 10, Issue 1, 2020 · pp. 24–36 Read article
-
Polymeric Hybrid Systems Engineered with Multiple-Stage Energy Absorption for Temperature Control
Abstract: Polymer–composite based phase change systems offer an effective strategy for adaptive thermal management; however, most existing systems exhibit single-stage latent heat transitions, limiting their applicability in environments with fluctuating thermal loads. In this study, a thermoplastic polyurethane (TPU) polymer matrix was reinforced with two microencapsulated paraffin-based phase change materials (PCM-A and PCM-B) to achieve multi-level latent heat storage behavior. The fabricated TPU/PCM-A10–B20 polymer–composite demonstrated two distinct endothermic transitions at approximately …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 146–155 Read article
-
Evaporative Cooling By Using Different Porous Materials
Abstract: The method of evaporative cooling involves raising the air temperature by causing water vapour in an airstream to evaporate. Waterneeds the latent heat of vaporisation to evaporate, and this heat is produced by ambient air and a drop in air temperature. A porousmedium is necessary for both direct and indirect evaporative cooling in order to allow heat and mass transfer between the medium'swater and the air moving through it, or …
Published in Journal of Refrigeration, Air conditioning, Heating and ventilation · Vol. 9, Issue 2, 2022 · pp. 29–37 Read article
-
Performance Analysis of Graphene Reinforced Sug-ar-Alcohol Based PCM for Thermal Energy Storage System
Abstract: The thermal-conductivity of the Phase Change Materials (PCMs) of thermal heat storage systems is improved by distributing nano-particles in the basic PCM for a faster rate of heat transfer. During the charging and discharging procedures, the heat transfer properties of the newly created Sugar-Alcohol based PCM dispersed with 1.0 wt% graphene nanoparticles in a shell and helical tube storage tank were examined. The helical tube configuration caused the melting and …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 133–147 Read article
-
Adaptation and Implementation of Solar Distillation Plants for Pure Water: A Review
Abstract: Abstract The need of pure water is increasing day by day, being scarcity of fresh water available on grounds. The one source for obtaining the pure water, by purification, can be looked upon from saline water or waste water. The methods of purifying such water are not economic to the large population. But the use of techniques like solar distillation can be very economic and efficient as well, because of …
Published in Journal of Water Pollution & Purification Research · Vol. 4, Issue 1, 2017 · pp. 1–3 Read article
-
Comparative Analysis of 3D-Printed and Molded Shape-Stabilized Phase Change Composites
Abstract: Thermal energy storage (TES) has become essential for efficiently storing and utilizing thermal energy across applications like industrial heating, power plants, batteries, medical devices, food preservation, and aerospace technology. Because of their high energy density, affordability, and environmental friendliness, phase change materials, or PCMs, are employed extensively. However, challenges like poor thermal conductivity and leakage limit their performance. To address these issues, 3D printing has emerged as a powerful tool …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 184–192 Read article
-
Smart Biopolymer–PCM Composite Modules with Embedded Wireless Thermal Sensing for Autonomous Energy Storage Applications
Abstract: The development of multifunctional polymer composite systems for intelligent thermal energy storage has gained significant attention due to the increasing demand for sustainable and autonomous thermal management technologies. In the present study, a wireless-integrated biopolymer–phase change material (PCM) composite module embedded with thermal feedback sensors was successfully fabricated and experimentally investigated for advanced thermal energy storage applications. Polylactic acid (PLA) was employed as the biodegradable polymer matrix, while paraffin wax …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 · pp. 193–205 Read article
-
Thermally Regulated Polymer-PCM Composites for Efficient Solar Energy Harvesting and Storage
Abstract: This study investigates the development of high-performance; shape-stabilized polymer composites infused with phase change materials (PCMs) for thermal energy storage in solar energy applications. Polyethylene glycol (PEG-6000) was employed as the core PCM due to its high latent heat and suitable melting point, while high-density polyethylene (HDPE) served as the supporting polymer matrix to provide structural stability. One of the primary limitations of PEG-based PCMs is their inherently low thermal …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 153–163 Read article
-
Stretchable Elastomer–PCM Composites with Bluetooth-Enabled Temperature Monitoring for Wearable Healthcare IoT Devices
Abstract: The rapid advancement of wearable healthcare technologies has created a growing demand for multifunctional polymer composites capable of simultaneously providing mechanical flexibility, thermal energy management, electrical conductivity, sensing capability, and wireless communication. In this study, a stretchable elastomer-based polymer composite integrated with a phase-change material and a Bluetooth Low Energy temperature monitoring system was developed for wearable healthcare Internet-of-Things applications. The polymer composite was fabricated using an Ecoflex silicone elastomer …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 · pp. 241–257 Read article
-
Boron Nitride Nanoplatelets and Aluminium Nitride Incorporated Organic Organic Eutectic Phase Change Materials with Enhanced Thermal Conductivity with Low-Loading Nanoadditives
Abstract: Miniaturized high performance electronic appliances generate tremendous heat during the duty cycle, has led research community to explore advanced thermal management strategies. Operating electronics at high temperature may result in malfunctioning of compact appliances. Thus, phase change materials (PCM) are applied to maintain isothermal temperature by implementing phase transition through latent heat. To improve the thermal conductivity and to deduce at suitable phase transition temperature of novel eutectic PCM, nanoplatelets …
Published in Journal of Polymer & Composites · Vol. 12, Issue 2, 2024 · pp. 1–9 Read article
-
Investigations of A Solar Dryer With Thermal Storage
Abstract: This study presents the design, building, and performance evaluation of a low-cost mixed-mode natural convection solar cabinet dryer in conjunction with a latent heat thermal energy storage system. The work's goal is to reduce post-harvest losses in rural and semi-urban areas by offering an effective and reasonably priced method of preserving agricultural goods. The dryer is made out of a transparent polycarbonate lid to allow for solar heat gain, an …
Published in Journal of Refrigeration, Air conditioning, Heating and ventilation · Vol. 13, Issue 1, 2026 · pp. 48–63 Read article
-
Nano-Silica Reinforced Crosslinked Biopolymer–PCM Composites for Improved Thermal Cycling Durability
Abstract: Crosslinked biopolymer–PCM composites reinforced with nano-silica were developed to enhance thermal cycling durability, leakage resistance, and structural stability for advanced thermal energy storage applications. A starch-based biopolymer was chemically crosslinked using citric acid to create a stable polymer network, while paraffin was employed as the phase-change medium and nano-silica (1–4 wt%) served as a multifunctional inorganic reinforcement. FTIR analysis confirmed successful esterification between citric acid and the polymer backbone, indicated …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1–10 Read article
-
Polymer–Gel Composite Phase Change Materials: A Functional Polymer Composite Approach for Solar-Thermal Energy Storage in Building Facades
Abstract: This study investigates polymer–composite phase change materials (PCMs) in the form of polymer–gel hybrids as multifunctional systems for solar–thermal energy storage in building façades. Paraffin- and PEG-based PCMs were embedded into polyurethane and acrylic gel matrices to create shape-stabilized polymer–composites with high PCM loading (70–80 wt%). Differential Scanning Calorimetry (DSC) confirmed distinct melting/freezing transitions at ~56°C (paraffin) and ~42°C (PEG), with enthalpy values of 120–150 J/g, closely matching theoretical predictions, …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 36–51 Read article
-
Phase Change Material in the Heat Exchanger for Improved Performance of Latent Refrigeration Storage Systems
Abstract: Using phase change materials (PCMs) in conjunction with a latent cool storage system is an efficient method of storing cool energy. It has the advantage of storage process with isothermal nature and storage of high energy density. Within last few years it has been inspected that in cool storage applications, PCM’s have been widely used. PCM’s are melted and solidified at wide ranges and temperatures and hence are attractive in …
Published in Journal of Refrigeration, Air conditioning, Heating and ventilation · Vol. 10, Issue 2, 2023 · pp. 19–29 Read article
-
Advancements and Emerging Trends in Thermal Energy Storage Technologies for Sustainable Energy Systems
Abstract: Rising global energy demand and environmental concerns have led researchers to investigate renewable energy sources as alternatives to fossil fuels. Solar and wind power have emerged as key players in the transition to more sustainable energy systems. Thermal energy storage (TES) technologies are critical to addressing the variability of renewable energies, allowing for a better management of energy, improved reliability, etc. This paper analyses the recent advances in the field …
Published in International Journal of Electrical Machine Analysis and Design · Vol. 3, Issue 1, 2025 · pp. 07–17 Read article
-
Comparative Performance of Phase Change Materials for Solar Thermal Storage System
Abstract: This paper is aimed at understanding the melting behavior of different Phase Change Materials (PCM) encapsulated in a spherical capsule. The melting process of PCM enclosed in spherical capsule has been investigated computationally and experimentally in the range of parameters useful for solar water heating applications. CFD predictions of the melting of two different PCMs viz. savE® HS-58 and Paraffin wax (PW) inside a spherical capsule have been obtained. Experiments …
Published in Journal of Alternate Energy Sources & Technologies · Vol. 2, Issue 1, 2011 · pp. 1–7 Read article