Search
28 articles for “Homogeneous dispersion”
-
Processing of Magnesium Metal Matrix Composite Reinforced with Graphene Nano Platelets through Vacuum Stir Casting and Investigating its Mechanical Behaviour
Abstract: AbstractThe application of metal matrix composites (MMCs) as structural engineering materials has received increasing attention in recent years. Their high strength and toughness at elevated temperatures coupled with low-density makes them suitable for use in applications where conventional engineering materials, such as steel are used. MMCs exhibit significantly higher stiffness and mechanical strength compared to matrix alloys, but often suffer from lower ductility and interior fracture toughness. MMCs have the …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 5, Issue 3, 2018 · pp. 21–29 Read article
-
Thermo-Mechanical Properties of Unsaturated Polyester Reinforced with Coconut and Snail Shells
Abstract: AbstractParticulate-filled polymer composites are becoming quite attractive because of their low cost and wide applications. In this study, the effects of coconut shell (CS) and snail shell (SS) volume fractions (5–50 vol. %) on the thermal and mechanical properties of unsaturated polyester resin (UPR) composite are investigated. The results show that tensile strength, elongation at break, flexural strength, and hardness of the composite increase as filler concentration increases. However, impact …
Published in Journal of Polymer & Composites · Vol. 2, Issue 2, 2023 · pp. 44–56 Read article
-
Wear Performance of Cylindrical Shaped Alumina Nanoparticles Filled Epoxy Composite
Abstract: Low cost high specific strength epoxy LY 556 and alumina nano filler is utilized in current research for developing a epoxy composite. A liquid dispersion method was adopted for fabricating epoxy alumina composite having 0.50 wt% of alumina reinforcement. For uniform and homogenous dispersion of reinforcement, ultra-sonification of 120 W is adopted. To study the effect of particle behavior, unfilled epoxy and 0.5 wt.% cylindrical alumina oxide filled epoxy composite …
Published in Journal of Polymer & Composites · Vol. 12, Issue 5, 2024 · pp. 94–100 Read article
-
Microstructure and Mechanical Characterization of AA390 and Si3N4 Metal Matrix Composite Using Severe Plastic Deformation
Abstract: Metal matrix composites (MMCs) have significant attention in recent years due to their potential for improved mechanical properties compared to conventional monolithic materials. This study focuses on the microstructure and mechanical characterization of a MMC comprising AA390 aluminum alloy reinforced with Si3N4 particles. The severe plastic deformation (SPD) process, Equal Channel Angular Pressing (ECAP), was employed to fabricate the composite with enhanced mechanical properties. The ECAP method was chosen as …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 17–30 Read article
-
Design and Characterization of High-Performance Polymer Nanocomposites for Aerospace Applications
Abstract: Polymer nanocomposites have revolutionized aerospace materials through mechanical strength, thermal stability, and lightness. A number of polymer matrices filled with nanofillers such as carbon nanotubes, graphene, and nanoclay considerably improved structural integrity, flame resistance, and environmental adaptability. However, fabrication techniques are still being optimized so that nanofillers are properly dispersed throughout, which may create contradictions between mechanical strength and process ability. This work tries to design and characterize high- performance …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 178–193 Read article
-
Bio-inspired Thermo-responsive and Self-Healing Polymer–PCM Hybrids for Next-Generation Smart Textile Applications
Abstract: The integration of phase change materials (PCMs) into flexible polymers represents a promising strategy for developing smart textiles with advanced thermal regulation and mechanical adaptability. However, the challenges of PCM leakage, poor mechanical strength, and durability under cyclic stress have limited their practical applications. In this study, we present a novel self-healing and elastic composite based on thermoplastic polyurethane (TPU) incorporating 30 wt% microencapsulated PCM (mPCM) and dynamic disulfide bonds …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 228–238 Read article
-
Enhancement of Mechanical Properties in Hemp Fiber-Reinforced Epoxy Composites Using Graphene Nanoplatelets
Abstract: This study investigates how incorporating graphene nanoplatelets (GNPs) influences the mechanical performance of hemp fiber–reinforced epoxy composites. Hemp fibers were chemically treated by alkali treatment to improve fiber–matrix adhesion owing to their high specific strength, stiffness, renewability, and environmental friendliness. Graphene nanoplatelets were dispersed in acetone by probe sonication and added to acetone epoxy matrix at a concentration of 0.5 wt% and 1.0 wt%, respectively. Composite laminates were prepared by …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 98–109 Read article
-
An Overview of Surface Coating Methodologies and Their Use in Technical Materials
Abstract: To safeguard the product or structure against chemical harm, a variety of procedures and materials can be applied in coating applications today. Nowadays, coatings are used extensively in manufacturing all over the world to increase efficiency and reduce expenses two factors that are essential to preserving the sector's profitability. Coated materials have greater strength compared to uncoated materials. A variety of materials, including bio glass, polymers, ceramics, strong and hard …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 19–35 Read article
-
Investigation of the independent and combined roles of Gr and ZrO₂ on strengthening behaviour of Al-7075 Composites
Abstract: This study investigates the effect of individual and hybrid reinforcements on the mechanical and microstructural behaviour of Al7075 composite fabricated using the 2-step stir-casting technique. Four compositions were made with the base Al-7075, Al-7075 3 weight % ZrO2, and Al-7075 3 weight % Gr as well as a hybrid composite Al7075 with 3 wt.% Gr, 3 wt.% ZrO2. 2-step stir-casting was used to increase the wettability of the particles, decrease …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1060–1075 Read article
-
High-Performance Carbon Nanotube-Reinforced Biodegradable Polymer Composites for Packaging
Abstract: The growing issues concerning the properties of petroleum-based plastics on the environment increased the demand for biodegradable alternatives and polylactic acid (PLA) is one of the most promising options available. However, its poor toughness, thermal resistance, and barrier properties limit broader applications in sustainable packaging. This study reports the fabrication and characterization of PLA-based nanocomposites reinforced with carbon nanotubes (CNTs) at varying loadings (0.1-2 wt.%). Structural analysis (FTIR, XRD) confirmed …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 183–194 Read article
-
Morphological and Dielectric Relaxation Responses of Polymer Stabilized Ferroelectric Liquid Crystal Composite Films
Abstract: Polymer-stabilized ferroelectric liquid crystal (GH-PSFLC) composite films have been prepared by polymerization-induced phase separation (PIPS) process as a function of polymer concentration. Epoxy polymer was homogeneously dispersed into FLC host matrix to create fibril network in the composite films. Twisted fibril-like network was observed through polarizing optical microscope through transmission mode. Dielectric relaxation spectroscopy of these composites shows that real part of permittivity decreases with polymer concentration. Goldstone relaxation mode …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 2, Issue 2, 2015 · pp. 8–12 Read article
-
Smart Biopolymer–PCM Composite Modules with Embedded Wireless Thermal Sensing for Autonomous Energy Storage Applications
Abstract: The development of multifunctional polymer composite systems for intelligent thermal energy storage has gained significant attention due to the increasing demand for sustainable and autonomous thermal management technologies. In the present study, a wireless-integrated biopolymer–phase change material (PCM) composite module embedded with thermal feedback sensors was successfully fabricated and experimentally investigated for advanced thermal energy storage applications. Polylactic acid (PLA) was employed as the biodegradable polymer matrix, while paraffin wax …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 · pp. 193–205 Read article
-
Synthesis of Zinc Oxide Nanoparticles Through Polymeric Precursor Route and their Integration into Functional Nanocomposites
Abstract: A polymer precursor approach for creating zinc oxide (ZnO) nanoparticles with regulated size and shape is described in this work. By stabilising and capping particles, the polymer-assisted pathway efficiently reduces particle agglomeration while facilitating controlled nucleation and growth. The surface shape and dispersion of the produced ZnO nanoparticles were assessed using the scanning electron microscopy (SEM). When compared to traditional synthesis techniques, the addition of polymer greatly enhanced surface homogeneity …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 883–890 Read article
-
Sonochemical Methods to Prepare Composes
Abstract: This purview is to link major and minor chemical reactions. Subjective has various unknown chemical reactivity those have announced by ultrasound. Cavity generation followed by implosive collapse have secreted chemistry to some extent so as pervert to scheme as well. Applicability of ultrasound has studied over chemical stimulus, scrubbing atomizer, crystallization, emulsification, dissolution, dispersion, defoaming, degassing, floatation, homogenization etc. Synthetic catalytic routes has subscriptive issued ultrasonic reverberation to regain some …
Published in Journal of Catalyst & Catalysis · Vol. 8, Issue 2, 2021 · pp. 1–7 Read article
-
Preparation and Properties of Blends of Thermoplastic Polymer with Thermoplastic Starch
Abstract: Problems in making biodegradable plastics are incompatible between hydrophilic/polar and hydrophobic/non-polar ingredients. Ingredients like compatibilizers were added to improve the compatibility between the two ingredients. The purpose of this study was to determine the effect of thermoplastic potato starch (TPS) content and two compatibilizers (maleic anhydride, MA, and dibutyl maleate, DM) on melt flow behavior, mechanical features (tensile, bending, and Izod impact test), phase morphology, thermal behaviors (DSC, and TGA/DTG), …
Published in Journal of Catalyst & Catalysis · Vol. 9, Issue 1, 2022 · pp. 16–29 Read article
-
Mechanical & Tribological Characterization of Al2024-Alumina-Graphite Reinforced Monolithic and Hybrid Composites
Abstract: This work investigates the mechanical characteristics of Al2024-Al2O3-Graphite reinforced monolithic and hybrid composites fabricated by the stir casting method. Exploratory work involved the fabrication of monolithic composites with varying Al2O3 contents (5-8 wt%) and hybrid composites with the ratios of Al2O3 (2-6 wt%) and Graphite (1-3 wt%) in matrix Al2024. For improving their dispersion, preheated reinforcement particles were introduced in matrix alloy at controlled stirring rates. A homogeneous particle distribution …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 823–836 Read article
-
Biodisintegrable Low-Density Polyethylene (LDPE)/Sago Starch (SS) Composites for Food Packaging Applications
Abstract: Research scientists are very interested in polysaccharide-filled plastics as a way to create a biodisintegrable polymer composite. The goal of the current study is to employ SS to create a biodisintegrable polymer composite, which could pave the way for a more user-friendly polymer composite in the future. In this study, LDPE/SS biodisintegrable composites were created by physically blending SS and LDPE in a Brabender mixer. The effects of varying the …
Published in Emerging Trends in Chemical Engineering · Vol. 9, Issue 3, 2022 · pp. 1–12 Read article
-
Electroactive Graphene–Polymer Nanocomposites for Self-Sustaining and Multifunctional Flexible Devices
Abstract: Graphene–reinforced polymer–composites were developed and systematically investigated to explore their multifunctionality in flexible electronic applications. The study specifically aims to correlate graphene-induced structure–property–function relationships with electroactive performance and self-sustaining behaviour in flexible devices. The hybridization of electroactive polymers—polyaniline (PANI), poly(3,4-ethylenedioxythiophene): polystyrene sulphonate (PEDOT:PSS), and polyvinylidene fluoride (PVDF)—with graphene nanoplatelets enabled simultaneous enhancement of electroactivity, energy-harvesting, and sensing functionalities. Morphological studies confirmed uniform graphene dispersion at 5 wt.% loading, forming continuous …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 260–271 Read article
-
Optimization of Direct Ink Writing Process Parameters for Liquid Silicone Rubber/TiO2 Composite Ink
Abstract: The purpose of this research is to develop and optimize the Liquid Silicone Rubber (LSR)/Titanium Dioxide (TiO₂) composite inks in Direct Ink Writing (DIW)-based 3D printing systems. The primary research objective was to use enhancement of mechanical, rheological, and dielectric characteristics of LSR using TiO₂ reinforcement but still retain extrusion stability and dimensional consistency. TiO₂ content (0, 5, 10, and 15 wt%) and catalyst and glycerol ratios were regulated and …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 240–259 Read article
-
Synthesis and Characterization of Forsterite Incorporated HDPE Composites for Microwave Substrate Application
Abstract: High Density Polyethylene (HDPE) combined with dispersed forsterite (Mg₂SiO₄) powder was utilized to fabricate polymer matrix composites (PMCs) aimed at high-frequency microwave substrate applications. Forsterite powders were synthesized using the mixed oxide method, and their phase purity was confirmed by X-ray diffraction (XRD) analysis. The dispersion and morphology of the ceramic filler within the HDPE matrix were examined through Scanning Electron Microscopy (SEM), ensuring a homogeneous distribution essential for optimal …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 109–120 Read article