Search
1205 articles for “over speeding”
-
Modeling, Analysis and LQR Control of an EV Differential using IPMSM
Abstract: Recently, the mechanical differential (MD) of vehicle has been replaced by electronic differential (ED) by means of electric motor. Electronic differential ensures dynamic and robust control of the vehicle behavior. The ED has been designed for an electrical vehicle (EV) based on IPMSM due to its some inherent advantageous features. The design of speed controller of an IPMSM mainly depends on its mathematical model. The mathematical model based speed controller …
Published in Journal of Control & Instrumentation · Vol. 7, Issue 2, 2016 · pp. 23–34 Read article
-
Small Scale Horizontal Axis Wind Turbine
Abstract: In this work, the performance analysis of a designed small scale horizontal axis wind turbine (HAWT) has been presented and optimized by varying span length and chord length. The HAWT blades are shaped to generate maximum power from the wind at minimum cost. The blades are designed by using QBlade software and simulated in blade element method (BEM).The values of tip speed ratio and power coefficient have been obtained as …
Published in Journal of Power Electronics and Power Systems · Vol. 4, Issue 3, 2014 · pp. 26–32 Read article
-
Rail and Coil gun Based Levitating hybrid Train
Abstract: Hybrid train is a train which is a hybrid of the concept ideas of coil gun, rail gun, halback array, magnetic levitation etc. Theoretically this train could achieve the fastest Speed an object could reach respect to its mass. This train could surpass sound barrier and could even be made to go to speed exceeding mach 3. But due to travel safety a certain speed limit can be implemented in …
Published in Trends in Electrical Engineering · Vol. 11, Issue 2, 2021 · pp. 35–41 Read article
-
Li-Fi’s Marketplace in the Future
Abstract: In this work, we are describing our project on the Li-Fi system. The full form of Li-Fi is “light fidelity”. It is the forerunner of Wi-Fi. Li-Fi is a type of data transmission technology that will be used in the future because of its causes and benefits. Wi-Fi and Li-Fi are not similar to each other. There are many differences between them in every aspect. In terms of speed, Li-Fi …
Published in Journal of Communication Engineering & Systems · Vol. 12, Issue 3, 2022 · pp. 1–5 Read article
-
Design of Front-end for Variable-frequency Drive
Abstract: A variable-frequency drive (VFD) is a device used in electro-mechanical drive systems to regulate the speed and torque of AC motors. It consists of a rectifier, a DC link, and an inverter, which work together to convert AC power into a variable frequency and voltage AC power supplied to the motor. By providing accurate speed regulation, VFDs enable energy conservation, enhanced process management, and reduced motor wear. They are commonly …
Published in Research & Reviews: A Journal of Embedded System & Applications · Vol. 11, Issue 1, 2023 · pp. 31–35 Read article
-
Physical Activity Based Vehicle Control Using ESP32
Abstract: This paper introduces an optimized and reliable project named Move-Buddy, a device that encourages physical movement in children. This is a way of engaging children in a game which causes them to move their body in different positions (e.g., wave their arms and move their legs) for the device to move forward, backward, left, and right according to the action performed by the child. The device uses multiple sensors placed …
Published in Research & Reviews: A Journal of Embedded System & Applications · Vol. 11, Issue 3, 2023 · pp. 32–42 Read article
-
Evaluation of UAV Spaying System for Droplet Size and Droplet Density Using Rotary Centrifugal Nozzles Boom
Abstract: India is the largest producer of mango (Mangifera indica L.) in the world, ranking first in both area and production. In the Konkan region, mango is the major fruit crop, with 1.10 lakh hectares of productive area dedicated to mango cultivation, resulting in an annual production of 2.6 lakh metric tons. Spraying is the most important operation in orchard crops. The newly developed spraying system was evaluated in the laboratory …
Published in Trends in Mechanical Engineering & Technology · Vol. 14, Issue 3, 2024 Read article
-
Review in Friction Stud Welding Of Aluminium to Steel
Abstract: The demand for friction stud welded aluminum/steel joints has increased in many significant applications including cryogenics, structural engineering, spacecraft, rocket fuel tanks and high vacuum chambers owing to their superior properties. In automobile engineering, there is a requirement to join a mild steel earthing pin which is in the shape of a stud to an aluminum car body. Aluminum and steel was considered to join using friction stud welding. This …
Published in Journal of Thermal Engineering and Applications · Vol. 8, Issue 3, 2021 · pp. 19–24 Read article
-
Assessment of a Wind Energy Conversion System for Sustainable Hydrogen Production by Alkaline Water Electrolysis in India: Effect of Geographical Location and Wind Turbine Type
Abstract: The use of wind energy for electricity generation and use of this electricity for hydrogen production by alkaline water electrolysis promises to be a truly sustainable scheme for the postulated hydrogen economy. This work addresses the feasibility assessment of a standalone wind energy based turbine generator system that meets the energy requirements of the electrolysis process at several locations in India. Energy requirement for electrolysis depends on the hydrogen production …
Published in Emerging Trends in Chemical Engineering · Vol. 4, Issue 2, 2017 · pp. 5–22 Read article
-
Experimental Test for the Replacement of Aluminum Sheets Instead of Steel Sheets in the Automotive Industry and the Effect of this Replacement
Abstract: Nowadays, vehicles cause air pollution due to high fuel consumption, and it has a direct relationship with increasing vehicle weigh. The increase of pollution will lead to rise in greenhouse gases that will cause special damages during a long period time. In this paper, instead of using steel sheets, aluminum sheets are proposed for the vehicle body and its interior components. It is attractive to increase its speed by reduction …
Published in Journal of Automobile Engineering and Applications · Vol. 7, Issue 3, 2020 · pp. 34–39 Read article
-
Vertical Opposed Piston Engine: A Review
Abstract: Nowadays many new technologies are available in our daily life. Now there is need to change the technology of automobiles also. We all know that we don't have more fuel in earth therefore we need to design new engines which are light in weight, more efficient, more powerful, have more speed, etc. In today's market, people want all these features in only one engine. People are also using hybrid engines, …
Published in Journal of Automobile Engineering and Applications · Vol. 3, Issue 1, 2016 · pp. 34–38 Read article
-
Effect of Varying Surface Grinding Parameters for AISI 1018 Mild Steel by Taguchi based PCA
Abstract: The main purpose of this work is to study the effects of surface grinding parameters on AISI 1018 Mild steel work surface by using three process parameters like Wheel speed (WS), Table speed (TS) and Depth of cut (DOC). This work was conducted on surface grinding machine with model number HMT-P452. Taguchi’s L16 orthogonal array is used which takes sixteen experimental runs to achieve the design matrix of surface grinding …
Published in Journal of Catalyst & Catalysis · Vol. 5, Issue 2, 2018 · pp. 5–14 Read article
-
Vibration analysis of Power transmission shafts in automobiles
Abstract: A power transmission shaft is considered in the present work and analyzed for vibrations. It is a shaft supported on single cylinder four stroke engine. Finite element analysis technique is applied to analyze for stresses and their intensities. The analysis is carried out for different engine speeds and later compared the results by using simulation software. It is observed form the results that there are critical speeds at which sudden …
Published in Journal of Experimental & Applied Mechanics · Vol. 10, Issue 3, 2019 · pp. 1–4 Read article
-
Performance Analysis of BLDC Motor: A Fuzzy Approach
Abstract: AbstractThe main objective of this paper is to study the performance analysis of a Brushless DC (BLDC) motor supplying different types of loads, and at the same time, deploying different control techniques. A Fuzzy controller is compared with the commonly used conventional controllers. The controller is designed to track variations of speed references and to stabilize the output speed during load variations. A comparison has been carried out by observing …
Published in Journal of Microcontroller Engineering and Applications · Vol. 6, Issue 2, 2019 · pp. 20–33 Read article
-
Surface roughness prediction in the turning operation by using experimental results and equation.
Abstract: This paper was discussed the values of surface roughness prediction models for turning EN24/817M40T steel (277 BHN) by using equation and experimental results. A factorial design technique has been used to study the effects of the main cutting parameters such as cutting speed, feed, and depth of cut, on surface roughness. The tests have been carried out using uncoated.A first-order prediction model within the speed range of 80-180 m min-1 …
Published in Journal of Materials & Metallurgical Engineering · Vol. 9, Issue 1, 2019 · pp. 27–30 Read article
-
Effect of Hot Induction Process on Bend Properties
Abstract: This paper discusses about the effect of processing speed and water flow rate on the mechanical properties of the hot induction bending of grade API5LX70 for the bending angle of 30o with the bending radius of 3D. Water flow rate & speed of the bending machine were varied to optimize the process parameters with respect to mechanical properties.
Published in Journal of Materials & Metallurgical Engineering · Vol. 2, Issue 1-3, 2012 · pp. 97–104 Read article
-
Sizing and Power Estimation Models of an Off-grid Wind Power Supply System in Sokoto, Nigeria
Abstract: AbstractThe exploitation of wind energy for electricity generation could be done by the use of wind turbines. The power output from the wind generator fluctuates due to the variability of wind speed and therefore storage facilities are needed for power supply stability. This research focuses on the wind power potential investigations, sizing of wind power system components and determination of the better wind turbines for residential power supply in Sokoto, …
Published in Journal of Nuclear Engineering & Technology · Vol. 10, Issue 1, 2020 · pp. 1–7 Read article
-
Comparative Study of Torque Ripple Minimization of PMSM using PI and Proportional Resonant (PI-RES) Controller
Abstract: The minimization of speed ripple of the permanent magnet synchronous motors (PMSM) in low speed range becomes a major problem while applying the PMSM to refrigerant system. Earlier, an iterative learning controller was applied in conjunction with the conventional proportional integral (PI) speed controller to minimize the speed ripple. Here, a frequency variable resonance controller is applied in conjunction with the conventional proportional integral speed controller as a PI-RES controller, …
Published in Journal of Power Electronics and Power Systems · Vol. 8, Issue 3, 2018 · pp. 17–23 Read article
-
Comparative Study of Microelectromechanical Switches for RF Applications: A Review
Abstract: Switches are very basic components for any communication application. The switch performance depends on their ability to allow a signal without loss and its speed of operation. In this paper, the different switches which are being used for RF application are presented along with their advantages and disadvantages. The main focus of this study is to provide comparative study about different microelectromechanical (MEMS) switches and also different techniques to improve …
Published in Journal of Semiconductor Devices and Circuits · Vol. 6, Issue 2, 2019 · pp. 6–12 Read article
-
Hard and Wear-Resistant Nanocomposite Thin Film Coatings
Abstract: Recent advancements in the hard and wear-resistant protective coatings have made high speed machining increasingly viable in the industries. The nanocomposite coatings have immense applications today in dry and high speed machining due their high wear resistance and high oxidation resistance properties. The high oxidation and wear resistance properties are obtained by addition of fourth element such as silicon to tertiary transition metal nitride compounds. In this work, a review …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 2, Issue 3, 2015 · pp. 28–32 Read article