Search
91 articles for “VLSI circuits”
-
Design and Implementation of an Efficient Ternary Control Unit
Abstract: Multi-valued logic (MVL) is emerging as a thrust area of research due to several advantages offered by them over the conventional binary logic. Ternary logic is a promising alternative to the binary logic design technique thereby attracting a wide community of researchers to contribute in the design of ternary processor. The control unit is effectively the nerve center of a processor that plays a vital role in generating the appropriate …
Published in Journal of VLSI Design Tools and Technology · Vol. 5, Issue 3, 2015 · pp. 55–70 Read article
-
Memristor Modelling for Common Source Amplifier Using 180 nm Technology
Abstract: The objective of this research paper is on memristor modeling for common source amplifier circuit using cadence virtuoso tool at gpdk 180 nm technology. A memristor is the fourth element count after resistor, inductor and capacitor in fundamental electrical circuits assumption is proposed by Leon Chua, its characteristics is based on already occurred principles of voltages (V), current (I), flux (ᵩ) and charge (q). Ohm’s law states relation voltage to …
Published in Journal of VLSI Design Tools and Technology · Vol. 5, Issue 3, 2015 · pp. 45–54 Read article
-
An Area Delay Optimized Carry-Select Adder
Abstract: In arithmetic and logic unit of digital signal processor (DSP), adder is the important hardware unit. Carry select adder (CSLA) is the best example of the adder used in DSP and it is widely used in many data processors to increase speed. So, the adder performance affects the overall system-performance. The Regular Square root (SQRT) CSLA consists of two Ripple Carry Adders (RCA), so it consumes more area due to …
Published in Journal of VLSI Design Tools and Technology · Vol. 8, Issue 3, 2018 · pp. 10–14 Read article
-
Implementation of DCC technique using differential amplifier based filter in 90nm CMOS technology
Abstract: Analog technique with feedback loop is applied to correct the duty cycle of any circuit without using more power. Pulse width modification is used to vary the duty cycle of clock signal. PMC cell is designed for expansion and contraction of pulse width. Differential amplifier based filter is used to detect the duty cycle of the particular clock signal. Differential amplifier and OpAmp are used to achieve adequate gain. The …
Published in Journal of VLSI Design Tools and Technology · Vol. 9, Issue 2, 2019 · pp. 13–22 Read article
-
Hardware Optimization of FPGA for I2C Master Protocol and Interfacing with EEPROM Slave
Abstract: This paper focuses on I2C (Inter Integrated Circuit) protocol master controller. I2C protocol was originally given by Philips semiconductors so that faster devices can communicate with slower devices and also allow devices to communicate with each other over serial bus without data loss. The I2C controller provides support for a communication link between integrated circuits and memory units on a board. I2C is a bidirectional serial bus which contains two …
Published in Journal of VLSI Design Tools and Technology · Vol. 5, Issue 2, 2015 · pp. 42–48 Read article
-
Carbon Nanotube Transistor Based Novel Ring Oscillator with Minimum Power Consumption at 32 nm Technology Node
Abstract: In this article an analysis of carbon nanotube field effect transistor based ring oscillator is performed. After analysis it was found that carbon nanotube transistor consumes less power in comparison to silicon transistor. CNFET is one possible candidate to substitute silicon-based integrated circuit (IC) technology, as the performance increase of conventional transistors witnessed during the last decades will arrive at its ultimate limits in the near future. Its present progress …
Published in Journal of VLSI Design Tools and Technology · Vol. 7, Issue 3, 2017 · pp. 51–54 Read article
-
Comparative Analysis of Class-AB Voltage Follower using DTMOS Transistor
Abstract: This paper describes a topology of voltage follower Class-AB Voltage Follower like Translinear voltage follower using MOS and DTMOS Transistor. The circuits are simulated in 90 nm technology. The results are used to compare the performance of the above voltage followers. All analysis was supported by the simulation results. The analysis are made in terms of gain, bandwidth and transient response using ELDO spice, IC station and Design architect of …
Published in Journal of VLSI Design Tools and Technology · Vol. 5, Issue 2, 2015 · pp. 64–70 Read article
-
Study and Analysis on Multi-gate MOSFET Design
Abstract: AbstractMulti-gate MOSFET is the emerging technology that is used in the area of low-power VLSI design. Multi-gate devices provide much better advantages over conventional MOSFET. As less power dissipation, decrease size, and more operational value could be obtained. Multi-gate MOSFET devices also reduce cost of production. Thus, design of electronics devices based on multi-gate technology is beneficial in today’s requirement. Basic MOSFET due to its reduction in size shows short …
Published in Journal of Semiconductor Devices and Circuits · Vol. 7, Issue 1, 2020 · pp. 1–7 Read article
-
Fault Detection Attainment for Embedded Cores based on Software Test Routines
Abstract: The test circuitry is designed in built-in-self-test (BIST) technique involves a system that applies the test signals and observes the corresponding system response. In this technique, the framework is embedded directly into the system hardware. The testing process performs efficiently, fastly and more economically than using an external test setup. Self-testing of embedded processors based on the test routines is an emerging method, since it employs a test resource partitioning …
Published in Journal of VLSI Design Tools and Technology · Vol. 8, Issue 1, 2018 · pp. 1–6 Read article
-
High Gain Antenna Array (2x1 and 4x1) Design for WLAN Application
Abstract: Micro-strip antennas became very popular in 1970s primarily for space borne applications. Today they are used for government and commercial applications. These antennas consist of a metallic patch on a grounded substrate. The metallic patch can take many different configurations. However, the rectangular and circular patches are most popular because of ease of analysis and fabrication, and their attractive radiation characteristics, especially low cross-polarization radiation. In high performance aircraft, spacecraft, …
Published in Journal of VLSI Design Tools and Technology · Vol. 8, Issue 2, 2018 · pp. 1–8 Read article
-
Implementation of a 4-Bit Synchronous Counter in SkyWater 130 nm CMOS Technology Using Open-Source EDA Tools
Abstract: As semiconductor technology continues to scale down, the physical layout of integrated circuits has become increasingly critical in determining performance, power consumption, and area efficiency. This paper presents the complete physical design implementation of a 4-bit counter, from Register Transfer Level (RTL) to GDSII, using the SkyWater 130 nm open-source Process Design Kit (PDK) and the OpenLane automated physical design flow. Functional verification of the RTL design was initially performed …
Published in International Journal of VLSI Circuit Design & Technology · Vol. 4, Issue 2, 2026 Read article