Search
1461 articles for “and Voges–Proskauer (VP) tests”
Nothing matched all of your words, so these match any of them.
-
Effect of Steel Fibre on the Flexural Strength of Self- Compacting Concrete
Abstract: With the increase in demand in the construction industry Self-Compacting Concrete is becoming more popular due to its versatile nature of improved efficiency. But the SCC possesses some properties which makes it brittle under tensile forces. The behavior of SCC as a structural material can be improved with the addition of Steel Fibres in adequate amount. In fact, the fibre reinforcement mechanism can convert the brittle behavior of concrete into …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 230–239 Read article
-
Investigation on Mechanical Properties of Geo Polymer Concrete With Fly Ash and Steel Fibers
Abstract: The goal of this project was to manufacture fly ash-based geopolymer concrete (FAC), a more environmentally friendly substitute for conventional Portland cement concrete (OPC) by using fly ash (FA) in place of cement. The study discovered that the properties of FAC were comparable to those of OPC, and that the concrete's performance was greatly impacted by the geopolymer's polymeric nature. The geopolymerization process was started with an alkaline solution, and …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 250–260 Read article
-
Enhancing Breastfeeding Practices Through a Biopolymer-Based Educational Intervention
Abstract: Background: Breastfeeding difficulties are common among new mothers, and knowledge gaps can contribute to these challenges. Educational interventions hold promise in improving breastfeeding practices. This study aimed to evaluate the effectiveness of a biopolymer-based educational intervention in enhancing mothers' knowledge and practices regarding breastfeeding problems and their prevention. Methods: A quantitative pre-post-test design was employed with a sample of 54 postnatal mothers in a multispecialty hospital. A biopolymer-based educational intervention …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 114–118 Read article
-
Vibration Characteristics of Copper-Aluminium Composite under Different Boundary Conditions: Experiment and Simulation
Abstract: The utilization of vibration analysis on the tapered beam significantly enhances the engineering investigation and design process. It is notable that the width of the tapered beam exhibits variation along its length, while the height remains constant. Experimental modal testing aims to determine modal factors such as natural frequency, damping, and mode shapes. A comparative study is presented in this paper, examining the vibrational characteristics of tapered beams composed of …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 190–203 Read article
-
New Generation Waste Material as Sustainable Ingredient in Concrete: An Experimental Approach
Abstract: E-waste, including devices like phones and computers, poses serious environmental risks. To mitigate these, the construction industry is exploring e-waste as a material to enhance concrete strength and durability. Hence, the present study assesses the performance of M40-grade high-strength concrete by replacing coarse aggregates with 0% to 30% e-waste plastics at various intervals. As the e-waste replacement increased, fresh concrete's workability decreased gradually. The mix containing 30% e-waste experienced the …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 141–156 Read article
-
The Examination of Design and Weight Optimization for a Light Motor Vehicle (LMV) Drive Shaft through the Utilization of a Composite Material Composed of Aluminum and Glass Fiber (Al + GF)
Abstract: Aluminum is primarily used in Metal Composites because of its lighter weight and higher strength. Glass fibers are wound around an aluminum shaft to create the composite. ANSYS results determine the relative amounts of aluminum and E-glass fiber in each shaft. The purpose of this study is to use a torsion test to evaluate the mechanical performance of a composite shaft composed of aluminum and glass fiber. The results are …
Published in Journal of Experimental & Applied Mechanics · Vol. 15, Issue 3, 2024 · pp. 1–17 Read article
-
Investigation on Tensile Properties of Redwood PLA Using FDM Process
Abstract: Fused Deposition Modeling (FDM) is an additive manufacturing technique employed to construct comprehensive 3-dimensional models using a variety of materials, catering to diverse applications. This study explores the fabrication of REDWOOD polylactic acid using (FDM) additive manufacturing processes. REDWOOD PLA, recognized for its biodegradability and renewable sourcing, holds promise as an eco-friendly material for 3D printing applications. The research investigates the tensile properties of REDWOOD polylactic acid (PLA) fabricated through …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 668–673 Read article
-
Optimization of Polymer-Enhanced Sustainable Concrete: A Composite Approach with Bentonite and Crumb Rubber Aggregates
Abstract: The disposal of rubber tyres has become challenging; on the other hand, the utilization of rubber tyres is also increasing daily in society. The successful use of crumb rubber as an alternative aggregate and bentonite as a partial cement replacement in concrete composites has been well established through prior research. These materials have individually demonstrated their potential to enhance sustainability, improve concrete properties, and reduce environmental impact, paving the way …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 701–715 Read article
-
Performance Analysis of Dual Junction Solar Cell Devices utilizing Subcells of In0.51Ga0.49P and GaAs to Study Key Solar Cell Parameters via TCAD based Simulation
Abstract: In the present work, a multi-junction solar cell was designed to obtain better performance over single-junction solar cells. The proposed structure is composed of different layers of diverse semiconductor materials stacked on each other. Here, an In0.51Ga0.49P/GaAs double-junction solar cell was outlined as having a distinctive composite material (GaAs) as the tunneling junction. To optimize the solar cell's effectiveness, In0.47Ga0.15Al0.37P was used in the window layer and the back-surface field …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 829–837 Read article
-
Effect of Drilling Process Parameters on Surface Roughness of LM6/B4C/Fly Ash Hybrid Composites
Abstract: This research seeks to assess the effect of process variables such as feed rate (FR), spindle speed (SS), drill material (DM) and reinforcement (R%) on surface roughness (SR) when drilling LM6/B4C/Fly ash hybrid composites. The stir casting process was used to fabricate the LM6/B4C/Flyash hybrid composites utilizing LM6 aluminum alloy as the matrix material and B4C/Fly ash as strengthening materials. Experiments were carried out using an L18 orthogonal array (OA) …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 898–906 Read article
-
Drilling Parameters Optimization in LM6/B4C/Fly ash Hybrid Composites by Taguchi Technique
Abstract: Aluminium matrix composites (AMCs) are challenging to machine due to its abrasive characteristics. Because of the broad adoption of MMCs, it is vital to create sufficient equipment to facilitate efficient manufacturing. The current study utilizes signal-to-noise ratio (S/N) analysis to determine the ideal machining parameters for drilling AMC’s. The goal with this study is to investigate the effect of feed rate (FR), drill type (D), speed (SS), reinforcing material R …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 890–897 Read article
-
Investigation of Chopped Basalt Strands for Concrete Beams Structures
Abstract: The current work unveils a sort of strategy for hacked basalt strands supported for cement footers. The material used to develop the bars are hacked basalt fiber, waterway sand, coarse total and fine total. In this the mechanical and flexure conduct of basalt fiber with differing rate to be utilized to test the crystal and advanced esteem is use to project the pillar. Absolutely six bars is projected out of …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 233–240 Read article
-
A Study on the Prevalence and Causative Factors of Anemia in Patients Undergoing Maintenance Hemodialysis
Abstract: Anemia is a common and serious issue in individuals with chronic kidney disease (CKD) who are on maintenance hemodialysis (MHD), greatly affecting their overall health and quality of life (QoL). Despite advancements in treatment, anemia remains a challenging issue in this population. This study investigates the prevalence of anemia and identifies the contributing factors in CKD patients on MHD with the aim of enhancing clinical management strategies. This study focused …
Published in Research and Reviews : A Journal of Medical Science and Technology · Vol. 14, Issue 1, 2024 · pp. 73–89 Read article
-
Integrative Machine Learning Approaches for Predicting the Rheological Behaviour of Soft Magnetorheological Elastomers
Abstract: Magnetorheological Elastomers (MREs) are advanced composite materials known for their ability to alter mechanical properties under external magnetic fields, making them highly valuable in adaptive damping systems, vibration control, and smart devices. The accurate prediction of rheological behavior in soft MREs remains a significant challenge due to the complex interplay between material composition and magnetic fields. To address this challenge, this study employs a multi-pronged approach that integrates traditional material …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 1083–1096 Read article
-
Composite Gel-Fibers and Solid-State-Processed Tapes Based on Disentangled Ultra-High Molecular Weight Polyethylene and Electrically Conductive Carbon Black: a Comparative Study
Abstract: In this study, oriented nanocomposite gel-spun fibers and solid-state-processed tapes were manufactured and analyzed. The fibers and tapes were produced using a specific type of nascent disentangled ultra-high molecular weight polyethylene (UHMWPE) reactor powder. As the filler, commercially available electrically conductive carbon black (CB) was used. The ultra-high filler content values up to 75 wt.% were achieved for the UHMWPE/CB gel-spun fibers, while the degree of filling was limited (up …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 151–165 Read article
-
Experimental Investigation of OPC Concrete with Incorporation of Glass Powder as Partial Substituent Material.
Abstract: This study presents an experimental survey aimed at evaluating the viability of incorporating glass powder (GP) as a partial substitute for cement in concrete matrix. The research focuses on assessing the effect of this sustainable alternative in concrete by investigating the various properties of fresh concrete such as workability, mechanical and durability aspects. Specimens were prepared with GP replacement to cement at 5%, 10%, 15%, and 20% levels, with comparative …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 1058–1068 Read article
-
Optimizing Image Processing with Verilog on FPGA: Techniques and Performance Enhancements
Abstract: The integration of image processing algorithms into hardware platforms, particularly FPGAs, presents a compelling opportunity for achieving high performance, low latency, and power efficiency in real-time applications. This study focuses on designing and implementing Verilog HDL-based optimal image processing methods for FPGA-based systems. The study explores the development of core algorithms, including edge detection, image enhancement, and adaptive filtering, to maximize resource utilization and processing speed on hardware platforms. Key …
Published in Journal of Semiconductor Devices and Circuits · Vol. 11, Issue 3, 2024 · pp. 46–53 Read article
-
Advanced Anomaly Detection in Cloud Infrastructures Using Deep Learning Algorithms
Abstract: It is critical to guarantee the stability and security of cloud environments as cloud computing is becoming the backbone of contemporary IT infrastructures. Neglecting to quickly identify and resolve anomalies, which might point to security breaches, performance problems, or system breakdowns, can lead to disastrous outcomes. The increasing size and complexity of cloud infrastructures are challenging the effectiveness of traditional anomaly detection methods. These approaches often depend on rule-based systems …
Published in Journal of Computer Technology & Applications · Vol. 16, Issue 1, 2025 · pp. 1–11 Read article
-
Piezoelectric Energy Harvesting Using A 10x10 Sensor Matrix with Integrated Circuit Design for Pressure Control
Abstract: This project aims to create a system that generates energy using piezoelectric technology, designed as a rectangular tile platform. The platform has two layers of sensors arranged in a 10 × 10 grid, connected in a mix of series and parallel setups. The top layer acts as a surface for external forces, like footsteps, while springs connect the layers to control pressure and maximize energy generation. A rectifier ensures the …
Published in International Journal of VLSI Circuit Design & Technology · Vol. 2, Issue 2, 2024 · pp. 47–53 Read article
-
Particle Size Effect on the Physicochemical Parameters of Water Media in Treatment of Contaminants of AGO and PMS
Abstract: Some of the physicochemical properties of contaminated water media with AGO and PMS was monitored upon the particle size effect and mix ratio. The physiochemical parameters monitored are potassium ammonia, iron and manganese concentration upon the performance of the formulated adsorbent immersed in the salt water and fresh water medium. The investigation demonstrates the occurrence of leaching in the process, which shows that some of the parameters adsorbed by the …
Published in Journal of Petroleum Engineering & Technology · Vol. 14, Issue 2, 2024 · pp. 27–36 Read article