Search
61 articles for “Arc welding”
-
A review on Evaluate the effect of process paramter on mechanical properties 6mm thickness SS317L weld joint for reciever application GTAW welding
Abstract: TIG welding is most important in the arc welding process. Especially of stainless steel and aluminum are more difficult to do. For better results, the optimal selection of process parameters is very important. In this work, the creator needs to decide the effect of different welding parameters like gas flow rate, current and included angle is selected. The experimental work organizes to optimize different parameter as per ASME section 9. …
Published in Trends in Mechanical Engineering & Technology · Vol. 10, Issue 3, 2020 · pp. 1–9 Read article
-
Experimental Investigation of Weld Strength in Pulsed Current TIG Welding of AA 5052 Alloys – A Technical Review
Abstract: TIG welding, also known as Gas Tungsten Arc Welding, is a method in which metal parts are welded together using heat or pressure. Inert gas is used to cover the electrodes and weld pools. Superior alloys such as stainless steel, aluminium, and magnesium alloys must be used to make high-quality weld connections. In 1825, the aluminium metal was conceived and produced. This project is based on the 5052 aluminum alloy …
Published in Trends in Mechanical Engineering & Technology · Vol. 12, Issue 1, 2022 · pp. 10–20 Read article
-
Investigate the effect of TIG welding process parameters on weld distortion of AA6061 - A Technical review
Abstract: TIG welding, also known as Gas Tungsten Arc Welding, is a process that uses heat orpressure to join metal pieces. The electrodes and weld pools are covered with inert gas. Toachieve high-quality weld connections, superior alloys such as stainless steel, aluminium, andmagnesium alloys must be employed. The aluminium metal was invented and produced in 1825.This project uses the 6061 aluminium alloy, which is one of nine different varieties of aluminium …
Published in Trends in Mechanical Engineering & Technology · Vol. 12, Issue 1, 2022 · pp. 31–38 Read article
-
Statistical Modeling for Weld Quality Assessment using AI SAW Welding of Mild Steel
Abstract: The main issue to the industries that apply Submerged Arc Welding (SAW) is quality assurance since the structural integrity dictates safety and the performance of the industry. The existing system of checking manuals is not only time consuming but also has human errors that make it mandatory to deploy automated intelligent systems. This study carries out an extensive comparison of the leading approaches based on the use of Artificial Intelligence …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 892–907 Read article
-
Analysis of Factors Affecting the Welded Joint using Design of Experiments: A Review
Abstract: The welding process over the period of time has grown into a more formidable process. Its application has also increased manifolds. However, with the increase in applications, it is also important to know the about the factors which affects the most on the strength of the welds. In this paper, the tensile strength of the welded joint has been considered. In this research, the Gas Metal Arc Welding has been …
Published in Trends in Mechanical Engineering & Technology · Vol. 8, Issue 3, 2018 · pp. 72–75 Read article
-
Optimization of Stellite Defect in Manufacturing of Engine Valves: A Review
Abstract: Intake and exhaust valves are the important components of an engine valves which are used to control flow and replacement of fuel gases inside the cylinder. This work mainly deals with defect known as stellite defect in different sizes of engine valves; and methodology adopted to prevent valve from stellite defect. Valve base material is low alloy steel (AISI 4140) and upper surface of engine valve is generally hard faced …
Published in Journal of Automobile Engineering and Applications · Vol. 3, Issue 1, 2016 · pp. 1–4 Read article
-
Influence of Different Fluxes on the Angular Distortion of A-TIG Welded 316L Steel Plates
Abstract: The conventional Tungsten Inert Gas (TIG) welding process is an autogenous welding process primarily used to weld thin metal sheets in the food processing and chemical industry. The process can weld almost all engineering materials but suffers from the limitation of slow speed and inability to weld thick sections. With the development of A-TIG welding, some of the drawbacks of traditional TIG welding have been addressed, where the activated flux …
Published in Journal of Polymer & Composites · Vol. 12, Issue 2, 2024 · pp. 99–103 Read article
-
Optimization Of Mechanical Properties Of 500/7 Grade Ductile Cast Iron (DCI) By Using SMAW: Applications In Reinforced Composites And Thermoplastics Through Taguchi & GRA
Abstract: Welding, a critical manufacturing process, is broadly engaged to join metals and thermoplastics using heat, pressure, or both. This study inspects the Shielded Metal Arc Welding (SMAW) method to optimize welding parameters and improve the mechanical properties of Ductile Cast Iron (DCI) grade 500/7, a material widely used in high-strength and thermal conductivity applications in aerospace and automotive sectors. Using an L9 OA (orthogonal array), experiments were conducted on nine …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 204–222 Read article
-
Performance Analysis of Bridgeless Converter Based SMPS used for Welding Application
Abstract: Abstract: This paper deals with performance analysis bridgeless converter based switched mode power supply (SMPS) of improved power quality. Power Factor Correction (PFC) based bridge less SMPS having so many applications in the area of welding power supply with IPC. This topology based on the constant voltage output and output current varied according to load changes. In the proposed topology, it is replaced the front end diode bridge rectifier with …
Published in Journal of Electronic Design Technology · Vol. 10, Issue 1, 2019 · pp. 27–33 Read article
-
Development of Lightweight Chassis and Efficient Drivetrain for Formula Student Applications
Abstract: The chassis and drivetrain of a Formula Student vehicle are designed, analyzed, and optimized in this research study with an emphasis on manufacturability, performance, and safety. The project emphasizes the use of advanced engineering tools such as SolidWorks for computer-aided design (CAD) and ANSYS for structural analysis to evaluate the chassis under various dynamic conditions. The primary objective is to ensure that the driver remains safe inside the cockpit while …
Published in Journal of Automobile Engineering and Applications · Vol. 12, Issue 3, 2025 · pp. 1–17 Read article
-
Selection and Mechanism of using active gas in GTAW Process – A review
Abstract: Gas tungsten arc welding process is known for its good quality welds. However, the lack of penetration of the process leads to low productivity. Many techniques have been implemented in the past to improve the joint penetration and thereby the productivity of GTAW process. In one of the technique, active gas like Carbon dioxide, Nitrogen or Oxygen is used in some proportion along with the inert gas. This addition of …
Published in Journal of Materials & Metallurgical Engineering · Vol. 8, Issue 1, 2018 · pp. 49–61 Read article
-
Voltage and Power Quality Control in Wind Power Application by Dynamic Compensation
Abstract: Power quality problem is a critical problem in a power system. Most of the pollution problems created in power system is due to the nonlinear nature of loads. Due to large amount of non-linear equipment, impact and fluctuating loads (such as locomotive, arc-furnace, welding equipment, etc.); wind power as a rule, does not contribute to voltage regulation in grids. Also wind power very often is a source of voltage sag …
Published in Trends in Electrical Engineering · Vol. 4, Issue 1, 2014 · pp. 1–8 Read article
-
Design and Analysis of Different Welding Joints
Abstract: Two parts linked together by the use of localised heat or fusion is called a weld; they join together either with or without the use of pressure or filler material application. Necessary heat required is obtained by burning of gas or by using an electric arc. The word joint and weld are different, weld means joining of two metals by heat and joint means a point where two parts are …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 4, Issue 2, 2017 · pp. 18–22 Read article
-
Automatic Laser Welding Machine Using PLCs
Abstract: This paper presents the design and implementation of an automatic laser welding machine controlled by a Programmable Logic Controller (PLC) technology. Laser welding has gained significant attention in various industries due to its precision, speed, and efficiency. However, manual operation of laser welding systems can be labor-intensive and prone to errors. The proposed system aims to address these challenges by automating the welding process using PLC-based control. The system architecture …
Published in International Journal of VLSI Circuit Design & Technology · Vol. 2, Issue 1, 2024 · pp. 9–15 Read article
-
Dissimilar Joining Of Aluminium Alloy to Copper Using Tungsten Inert Gas Welding Process
Abstract: Aluminium-copper dissimilar joints are applicable to electrical industry. 2 mm thick aluminium alloys (A1100) sheet is joined to 1 mm thick copper (Cu-DHP) sheet using tungsten inert gas welding (TIG) process. The effect of process parameters like heat input, torch orientation, arc weaving on mechanical properties of the joint are studied. In this combination the molten pool generated by melting of aluminium edge will wet the coppersurface to form a …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 5, Issue 2, 2018 · pp. 15–20 Read article
-
Fluorescence Emission Enhancement in Crystalline Photonic Structures
Abstract: One of the two ways that a material that has absorbed light or other electromagnetic radiation can emit light is through fluorescence. Fluorspar is a substance that can be added to welding compounds to facilitate easier flow; the word fluorescent is derived from the Latin fluere, which means "to flow." LED lights, clothing that glows in "black light," or light sources that contain UV or blue light, and butterflies like …
Published in International Journal of Crystalline Materials · Vol. 1, Issue 2, 2024 · pp. 35–48 Read article
-
Optimization of Process Parameters for Cu90Ni10 Alloy Processed by Wire Arc Additive Manufacturing (WAAM) Using an L9 Orthogonal Array
Abstract: Abstract Wire Arc Additive Manufacturing (WAAM) has gained significant attention in recent years as a promising technique for producing complex metallic components. This study focuses on the processing of Cu90Ni10 alloy using WAAM and employs an L9 orthogonal array to optimize the mechanical properties of the resulting components. Cu90Ni10 alloy is known for its excellent corrosion resistance and electrical conductivity, making it a critical material in various industries, including aerospace …
Published in Journal of Polymer & Composites · Vol. 11, Issue 8, 2023 · pp. 292–301 Read article
-
Additive Manufacturing of rocket propulsion system
Abstract: In recent years plenty of research is going on to produce effective manufacturing techniques which can produce complex unique designs with reduced cost and lead time for aerospace applications. In this aspect, Additive manufacturing is getting a wide range of popularity in the aerospace manufacturing domain due to its vast applications and advantages. In terms of geometric flexibility and processing time, additive manufacturing outperforms conventionalmanufacturing processes. Additive manufacturing has found …
Published in Journal of Materials & Metallurgical Engineering · Vol. 12, Issue 2, 2022 · pp. 1–9 Read article
-
Additive Manufacturing of Rocket Propulsion System: A Review
Abstract: In recent years plenty of research is going on to produce effective manufacturing techniques which can produce complex unique designs with reduced cost and lead time for aerospace applications. In this aspect, Additive manufacturing is getting a wide range of popularity in the aerospace manufacturing domain due to its vast applications and advantages. In terms of geometric flexibility and processing time, additive manufacturing outperforms conventional manufacturing processes. Additive manufacturing has …
Published in Journal of Materials & Metallurgical Engineering Read article
-
Application of Thermal Spray Coatings for Corrosion Control in Oil and Gas Refineries
Abstract: In today’s context, Thermal Spray Coating (TSC) has emerged as a highly durable and reliable alternative to traditional Hot-Dip Galvanizing (HDG). It is increasingly being adopted for both new and existing industrial structures due to its long-lasting protection—often exceeding 25 years—while requiring little to no maintenance. Unlike HDG, which cannot be welded on-site and often poses challenges with repair methods such as liquid coating or cold spray, TSC offers greater …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 106–115 Read article