Search
266 articles for “ARM”
-
Comparison of 11-Atom Armchair Graphene Nanoribbons and Zig-Zag Carbon Nanotubes in Polymer Composites Under Various Bias Voltages: A Study of Electronic and Transmission Properties
Abstract: In this research, 11-atom zig-zag carbon nanotubes (ZCNTs) and 11-atom armchair graphene nanoribbons (AGNRs) were studied under applied bias voltages at 50, 150, and 300 millivolt levels. The focus was on understanding their behaviour concerning transmission qualities, current-voltage (I-V) characteristics, and energy-momentum (E-K) diagrams. The Non-Equilibrium Green's Function (NEGF) approach was employed to analyse various electronic properties for ZCNTs and AGNRs, including transmission, E-K relationships, and I-V characteristics. The results …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 126–134 Read article
-
Development of Robot Arm Fingers with Polymer Soft Materials
Abstract: Lightweight soft material applications have attracted attention to Basalt Fiber Reinforced Polymer (BFRP) laminates because of their impressive mechanical characteristics. The impact response and stress-strain behavior of epoxy resin laminates armored with basalt fiber and banana fiber are investigated during this project using computational and experimental approaches. The hand lay-up method was employed to create laminates with a thickness of 3 mm, dimensions of 300x300 mm², and a layout of …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 432–439 Read article
-
Embedded Real Time Operating Systems Performance Analysis for ARM7 Platform
Abstract: An embedded RTOS is a software part of an embedded system that is used in the almost all the real-time application development process. It has a considerable effect on the reliability, robustness and performance of system under design and test. This paper addresses the concern of parameterized performance characteristics of two different RTOSs i.e. μC/OS-II and FreeRTOS ported on same common controller platform from ARM7TDMI family. Different OS services are …
Published in Current Trends in Signal Processing · Vol. 4, Issue 2, 2014 · pp. 24–29 Read article
-
Thermal and Thermoelectric Generation Using Geothermal Energy Extraction Through Cogeneration System
Abstract: The manuscript has focused on the evaluation of the improvement of energy efficiency in using geothermal energy for heat and electricity generation through additional thermoelectric production to conventional heat transfer processes. The proposed system uses Peltier rings made up of a serial and parallel Peltier cells grouping, as part of the upward and downward ducts that connect the geothermal heat exchanger and the surface heating system. The new system can …
Published in Journal of Alternate Energy Sources & Technologies · Vol. 11, Issue 1, 2020 · pp. 58–71 Read article
-
RF Based 3-Axis Robotic Arm using MEMS
Abstract: This 3-axis MEMS accelerometer are used in various applications like human–machine interactive games; for this application, hand gesture problem is used. This setup includes a number of 3-axis accelerometers on fingers and back of the palm to measure dynamic and static gestures, a programmable microcontroller to detect hand postures of American Sign Language and send them to a host via serial communication and analog multiplexer. The apparatus consists of sensors …
Published in Journal of Control & Instrumentation · Vol. 9, Issue 3, 2018 · pp. 15–20 Read article
-
Design of EMG based Control System for Prosthetic Arm
Abstract: Prosthesis, field of bio-mechatronics, is an artificial extension used to replace the function or appearance of a missing limb or lost body part due to injury (traumatic), to correct congenital deficiencies or to supplement defective body parts. A myoelectrically controlled prosthesis detects muscle contractions using electrodes and this electrical activity acts as a signal to activate the prosthesis. In the presented work, the EMG signal is acquired using surface electrodes …
Published in Journal of Electronic Design Technology · Vol. 4, Issue 2, 2013 · pp. 1–6 Read article
-
Smart swab testing robotic arm
Abstract: Coronavirus disease (COVID-19), influenza, respiratory syncytial virus, Bordetella pertussis infection (whooping cough), Staphylococcus aureus infections of the nose and mouth, and various allergies are all possibilities. It is spread by respiratory droplets and close contact and is caused by an infection of extreme acute respiratory syndrome. To Coronavirus disease (COVID-19), influenza, respiratory syncytial virus, Bordetella pertussis infection (whooping cough), Staphylococcus aureus infections of the nose and mouth, and various allergies …
Published in Journal of Microcontroller Engineering and Applications · Vol. 8, Issue 2, 2021 · pp. 48–50 Read article
-
Over Expression of Genes at Long Arm of 21 Chromosome in Case of Down Syndrome
Abstract: Down Syndrome (DS) is a genetic disorder which is caused due to trisomy at chromosome 21 or gene dosage imbalance. DS leads to mental retardation in humans. It is a multisystem disorder as it affects several systems of our body like cardiovascular, respiratory, gastrointestinal, neurological, hematopoietic and musculoskeletal system. The principal cause of DS is unknown yet. Some factors are responsible for DS. like reproduction at advanced maternal age, folic …
Published in Research and Reviews : A Journal of Immunology · Vol. 5, Issue 2, 2015 · pp. 27–34 Read article
-
Well Integrity and Reservoir Behavior under Sudden Field Shutdowns During Armed Conflicts: A Comprehensive Technical Review
Abstract: In the oil and gas industry, the sudden and unplanned cessation of operations resulting from armed conflicts or pandemics typically poses complex and multifaceted technical challenges to both well integrity and reservoir behavior. Minimal or no opportunity for proper pre-shutdown preservation procedures in unplanned shutdowns, unlike planned shutdowns that follow established operational protocols. The mechanisms and consequences of well integrity degradation and reservoir performance alteration under such conditions are synthesized …
Published in Journal of Petroleum Engineering & Technology · Vol. 16, Issue 2, 2026 · pp. 40–52 Read article
-
Modelling of Wind-Wave Misalignment for Floating Offshore Wind Turbines
Abstract: The influence of the combined effects of wind and waves onto the performance of a floating offshore wind turbine (FOWT) is analyzed. A study of the wind conditions relative to the position of the aerodynamic rotor has been made, analyzing how the angle of incidence of the wind (angle of attack) varies with the wind direction and the inclination of the wind turbine mast as a consequence of the undulatory …
Published in Journal of Offshore Structure and Technology Read article
-
Heat Sink-PCM Device for PV Efficiency Improvement
Abstract: This paper is focused on the development of a second stage of a previous work where the PV panel efficiency is improved by using a hybrid system made up of a PCM attached to the rear side of the panel. This evolved stage incorporates a heat sink unit to improve the distribution of the heat removed from the panel; this improvement reduces the elapsed time to reach the steady state …
Published in Journal of Thermal Engineering and Applications Read article
-
Simulation of Electric Vehicles DC Engine Performance
Abstract: This works develops a simulation model to predict the performance of direct current electric motors for electric vehicles (EV), mainly focused on the required power and mechanical torque as a function of the driving conditions. The simulation, therefore, has been based on the dynamic conditions of the electric vehicle to reproduce the current driving in urban routes or intercity travels. The model has been applied to synchronous and asynchronous transmission …
Published in Journal of Automobile Engineering and Applications Read article
-
Control System Operational Protocol for Dual DC Electric Motor Configuration in Electric Vehicles
Abstract: This paper is focused on the analysis of the performance of DC electric motor for electric vehicles (EV) in urban and intercity routes. The paper analyzes the different driving conditions in both types of routes reproducing the most current situations and how they influence the electric motor performance. The study is focused on a dual electric motor configuration, series and parallel, which equips an electric vehicle prototype, evaluating the power …
Published in Journal of Mechatronics and Automation Read article
-
Rooftop Layout Optimization for PV Installation using GIS
Abstract: In this work, we develop a new modelling process to optimize the PV installation layout on industrial building rooftops; the model searches for maximizing the number of installed PV panels in a defined spot area, characterized by its shape, size, tilt and orientation. The study focuses on areas of latitude between tropics, but is useful for other latitudes. The method is applied to an industrial conglomerate of reference, made up …
Published in Journal of Remote Sensing & GIS Read article
-
Application of GIS tools to the Improvement of Energy Supply in PV Rooftop Installations
Abstract: Present work studies the energy supply from photovoltaic (PV) installations in industrial conglomerates using the rooftops as a surface to install the PV panels. The study is based on a modelling procedure that takes into account the specific characteristics of the rooftop, shape, size, azimuth and inclination, using GIS tools to identify these parameters for every single rooftop. Modelling has been developed modifying the tilt angle of the PV panel …
Published in Journal of Remote Sensing & GIS Read article
-
Efficient Automation Solutions: Building a Budget-friendly Cylindrical Robotic Arm for Component Handling
Abstract: Design and Development of Automation of Loading and Unloading to machine fixture” This Setup involves the use of automation solution to reduce operator fatigue and increase efficiency. Industries in the recent day concentrating on CNC machineries for mass production by replacing conventional lathes to improve productivity but loading and unloading of job carried over by manual, However Present work, machine tool manufacturer are coming with solutions including automatic loading and …
Published in International Journal of Industrial and Product Design Engineering · Vol. 1, Issue 1, 2023 · pp. 6–15 Read article
-
Water reservoir engineering and management
Abstract: This work aims to develop a practical system to store water in times of abundance and reuse it in times of scarcity. The proposed system uses natural caves, caverns, or empty underground spaces from mining or oil or gas extraction to store water. The geological structure of the water reservoir should be a non-porous substrate to avoid leakage. Water collection comes from dam discharge during thaw times or river flooding, …
Published in Journal of Water Resource Engineering and Management · Vol. 11, Issue 1, 2024 · pp. 1–12 Read article
-
Improved Marine Wind Farm Layout
Abstract: This work proposes a new marine wind farm layout. The new configuration is based on the hybridization of alternating lift-force and drag-force wind turbines. Lift-force wind turbines are characterized by a high output power and large dimensions, while drag-force wind turbines have moderate power output and reduced size. The proposed layout inserts the drag-force turbines in the free space the lift-force turbines leave, using the turbulent wind to generate power …
Published in Journal of Offshore Structure and Technology · Vol. 11, Issue 1, 2024 · pp. 1–12 Read article
-
Hydrogen Storage System for Household Installation
Abstract: In this work, we study domestic renewable energy installations using compressed gaseous hydrogen as a storage system. The article analyzes the suitability and feasibility of this installation type considering energy, technical, and security aspects. The proposed configuration represents an alternative to the classical storage energy system in batteries, reducing dependence on grid supply for a negative balance of self-power generation to energy consumption. The hydrogen storage system is valid for …
Published in Journal of Power Electronics and Power Systems · Vol. 14, Issue 3, 2024 · pp. 22–40 Read article
-
Precipitable Water for Human Consumption in Rural Areas: Calculation Method and Engineering Design
Abstract: This work describes a methodological process to estimate the precipitable water for human consumption as a function of meteorological parameters like ambient and dew point temperature, water vapor and ambient pressure, and relative humidity. The paper uses empirical correlations to determine the most accurate procedure for atmospheric rainwater, resulting in a simple relation between precipitable water and dew point temperature as the highest accurate one. The study shows the dew …
Published in Journal of Water Resource Engineering and Management · Vol. 11, Issue 3, 2024 · pp. 41–57 Read article