Search
1205 articles for “over speeding”
-
Single-Input Fuzzy Logic Controllers for Efficiency Maximized Separately Excited DC Motor
Abstract: In this paper, three single-input fuzzy logic controllers are designed to control field current, armature current and speed of efficiency maximized separately excited DC motor. The necessary of field controller is to maximize the efficiency by tracking the optimized field current for different operating points. In contrary to the conventional fuzzy logic controller which requires at least two inputs variables and nine rules, the proposed controller requires one input and …
Published in Journal of Power Electronics and Power Systems · Vol. 4, Issue 2, 2014 · pp. 24–32 Read article
-
Direct Power Control of Induction Motor Drive
Abstract: Different variable frequency strategies have been developed for control of induction motors including V/f scalar control; field oriented control (FOC), and direct torque control (DTC). Recently, direct power control (DPC) has been developed to control dual-fed induction generators (DFIGs) and permanent magnet synchronous generators (PMSGs). In this paper, DPC is employed for speed control of induction motors fed by a voltage source inverter. DPC is basically similar to DTC method …
Published in Journal of Power Electronics and Power Systems · Vol. 4, Issue 2, 2014 · pp. 48–55 Read article
-
Development of Slip Power Recovery Scheme sing Buck-Boost Chopper for Performance enhancement of Wound Rotor IM Drive
Abstract: This paper presents the mathematical modeling and testing of wound rotor induction motor drive (WRIMD) to develop the slip power recovery scheme (SPRS) using buck-boost chopper control techniques improving the performance of drive. The main focus of this research work is on the understanding of methodological development of Simulink model of SPRS. Various mathematical equations describing performance characteristics of WRIMD using SPRS with buck-boost chopper are derived. The performance parameters …
Published in Journal of Power Electronics and Power Systems · Vol. 12, Issue 2, 2022 · pp. 44–63 Read article
-
Modeling of Maximum Power Point Tracking Controllers for Wind Generation System using Hill Climb Searching Technique
Abstract: In this paper, based on a low-cost, small-scale application, presents a Maximum Power Point Tracking (MPPT) controller for wind generation systems (WGS). The Hill Climb Search approach served as the foundation for the development of the MPPT algorithm. To account for the inertia of wind turbines, an enhanced hill-climb searching approach has been created as a fundamental component of the max-power extraction algorithm. Under varying wind conditions, the generator can …
Published in Journal of Power Electronics and Power Systems · Vol. 13, Issue 3, 2023 · pp. 39–47 Read article
-
Effect on Welding Parameters on FSW of Aluminium Alloys 7075 T6 with Varying Tool Geometry
Abstract: The present study is to investigate effect of tool pin profile over the friction stir welding of aluminium alloys 7075 T6. The welding process is to be conducted on varying the welding process parameters such as tool rotation speed (rpm), welding speed (mm/min) and tool pin profile. In this work, tensile strength tool rpm increase UTS in FSW joint decease up to certain level, including effect tool rpm on weld …
Published in Journal of Production Research & Management · Vol. 7, Issue 3, 2017 · pp. 27–32 Read article
-
Optimization of Multiple Performance Characteristics Using Desirability Function Analysis (DFA)
Abstract: In present days the manufacturers are facing many challenges in setting of optimal process parameters while machining in order to achieve multiple performance characteristics. The present work is to investigate the effect of the drilling process parameters on the multiple responses of Volume of material removal rate (VMRR) and surface roughness (Ra). The experiments were carried out on AA6082 material using taguchi’s L16 Orthogonal array with carbide twisted drills. The …
Published in Journal of Production Research & Management · Vol. 8, Issue 2, 2018 · pp. 23–29 Read article
-
A Review on Process Parameter Optimization of TIG Welding of SS316
Abstract: In this audit paper the creator needs to decide the effect of different welding parameters on the weld dot of SS316 welded joint. In this examination the diverse method is utilized to upgrade the distinctive welding parameters like speed, current, gas stream rate on the quality of the material. The outcome demonstrates that speed is the best variable to have most noteworthy twist quality; and current is utilized to get …
Published in Journal of Production Research & Management · Vol. 5, Issue 3, 2015 · pp. 34–38 Read article
-
Signal Integrity Analysis of Single Walled Carbon Nano Tube based Interconnects at 32 nm Technology Node
Abstract: The rising demands for ultra-high-speed processors and portable devices have made the transistor and interconnect scaling a challenging issue in present days. In this work, the impedance parameter of copper and CNT based interconnects are calculated at 32 nm technology node for different lengths. The performances of CNT based interconnects are analyzed and compared with Cu based interconnects in terms of crosstalk. The conventional copper interconnects are not able to …
Published in Journal of Semiconductor Devices and Circuits · Vol. 5, Issue 1, 2018 · pp. 33–42 Read article
-
An Optimized 32 bit Carry Select Adder Using Modified BEC
Abstract: AbstractAdders play a major role in addition of numbers, multiplications and other advanced processors’ design. Among the conventional adder structures, carry select adder is known to be fastest adder. This adder circuit is used for the design of high speed processors. The CSLA adder architecture is such that it is of less power dissipation, area efficient and high speed. CSLA circuit for 8, 16, 32 bits is designed without multiplexer …
Published in Journal of Semiconductor Devices and Circuits · Vol. 5, Issue 2, 2018 · pp. 27–32 Read article
-
An Efficient Tree Structure 32-Bit Brent-Kung Adder for Reducing Time Delay and Memory Utilization
Abstract: AbstractBrent-Kung adder is such of the parallel prefix adders secondhand for speeding of the operation. Parallel prefix adders are the fast adders and dig the arithmetic operations at the expeditious rate. Most Industries are like TMSC, Texas, are used by parallel prefix adders seeing of their advantages compared to a variance adder. Parallel prefix adders are faster and area efficient. Parallel prefix adder is a campaign for increasing the speed …
Published in Journal of Semiconductor Devices and Circuits · Vol. 5, Issue 3, 2018 · pp. 29–35 Read article
-
A Review on High Electron Mobility Transistors
Abstract: AbstractThe demand for high speed semiconductor devices is increasing in recent years with the rapid development of the high frequency wireless and fiber optical communication systems. High electron mobility transistor (HEMT) is an important device and an excellent candidate for millimeter, sub-millimeter and microwave applications. Also, these devices have high frequency, high speed, low noise, high breakdown voltage, low cost and other power handling capabilities. Due to these reasons, they …
Published in Journal of Semiconductor Devices and Circuits · Vol. 3, Issue 2, 2016 · pp. 1–10 Read article
-
Tracking of Maximum Power Point for SPV Systems
Abstract: AbstractThis paper presents the optimization algorithm based maximum power point tracking techniques. Optimization of output of shaded and un-shaded photovoltaic array under either it is static or dynamic whether condition is the primary goal of each MPPT techniques. There are various aspects of each MPPT techniques such as cost effectiveness, simplicity of hardware and software, its implementation, requirement of sensor, level of popularity, level of accuracy and its convergence speed. …
Published in Journal of Semiconductor Devices and Circuits · Vol. 6, Issue 3, 2019 · pp. 33–45 Read article
-
Development of Mathematical Model for Tool Wear Rate Using 3-Level Response Surface Methodology
Abstract: Tool wear is the progressive loss of material from the surface of tool in the form of very small metallic particles. From decade tool wear rate was used as major criteria to predict the tool life. However, tool wear rate only measures principle wear, i.e., flank wear and face wear. In order to assesses the real damage to the tool and consider other tool wear like chip, notching, primary and …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 3, Issue 2, 2016 · pp. 1–10 Read article
-
Effect of Surface Texture on Pressure Distribution in Hydrodynamic Journal Bearing
Abstract: This paper presents an analysis of the pressure distribution of hydrodynamic journal bearing for different surface texture, velocity variation and load variation. The performance of journal bearing depends on speed, load carrying capacity, viscosity of oil and temperature condition. Therefore, the effects of these parameters on the performance of journal bearing, on the pressure distribution and on the load carrying capacity have been analyzed on the basis of number of …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 3, Issue 2, 2016 · pp. 11–18 Read article
-
Educational Review on the Applications of Diamond-Like Carbon Films in Fluid Engineering
Abstract: In this present review paper, author has described the applications of diamond-like carbon (DLC) films in microfluidic devices from the point of view of materials-science. According to author’s earlier reports, the speed of surface-driven water flow is varied by the coating of DLC films in PMMA microfluidic devices. Also, according to author’s earlier reports, the speed of surface-driven water flow is varied by the coating of DLC films in SU-8 …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 6, Issue 3, 2019 · pp. 1–7 Read article
-
Vector Signal Transceiver (VST) in LabVIEW: A Review
Abstract: AbstractOver the past few decades, the increasingly popular architecture of RF systems with software has become increasingly popular. Almost every commercial automated RF system (COTS) today uses application software for communication via the bus interface with the device. As the complexity of radio frequency applications is increasing, engineers are constantly faced with the dilemma of increasing functionality without increasing testing time and, ultimately, to verify the cost. Although improvements in …
Published in Journal of Telecommunication, Switching Systems and Networks · Vol. 5, Issue 1, 2018 · pp. 1–5 Read article
-
Dual Powered Two-wheeler for Vendors
Abstract: Today the major problem faced by the Indians is the day by day fuel cost increment. We are introducing a new method to reduce fossil fuel usage without compromising on the efficiency of our two-wheeler with reduction in the overall fuel cost. We can increase the efficiency and reduce pollution by the usage of this dual powered vehicle. The objective of this paper is to construct an efficient petrol bike …
Published in Journal of Telecommunication, Switching Systems and Networks · Vol. 6, Issue 2, 2019 · pp. 39–48 Read article
-
LTE & 5G NR Carrier Aggregation Network Optimization through Advanced Measurement Configuration
Abstract: The ability to merge numerous frequency carriers—component carriers—to increase transmission bandwidth and throughput speeds over what can be achieved with a single carrier is known as carrier aggregation, and it is a crucial technology in 4G LTE and 5G networks. Cellular devices may attain gigabit data speeds by combining carriers from several frequency bands, such as 600 MHz to mm Wave frequencies, to increase downlink and uplink capacity. This study …
Published in Journal of Telecommunication, Switching Systems and Networks · Vol. 10, Issue 2, 2023 · pp. 35–45 Read article
-
Design of Three-Stage Pipelined Floating Point Arithmetic Operators
Abstract: Some embedded systems perform signal processing operations (Fourier transform, filtering) as for example for the recognition voice, high quality audio and control of critical systems (airplane, rocket). This type of operation may require the use of floating numbers. This paper presents the hardware implementation of floating point arithmetic operators for addition, subtraction, multiplication using the IEEE-754 single precision format. Proposed architecture follows two different RTL approach, Melay FSM and multiplexer …
Published in Journal of VLSI Design Tools and Technology · Vol. 8, Issue 2, 2018 · pp. 9–22 Read article
-
A Common Mode Scan Based BIST for Stuck-at-Fault and Path Delay Fault
Abstract: Testing for delay and stuck-at faults requires two pattern tests and test sets are usually large. Built-in self-test (BIST) scheme is attractive for comprehensive testing. The BIST test pattern generators (TPGs) for such testing should be designed to ensure high pattern-pair coverage. In the proposed work, necessary and sufficient conditions to ensure complete/maximal pattern-pair coverage for sequential circuit have been derived. A new test data-compression scheme is an effective approach …
Published in Journal of VLSI Design Tools and Technology · Vol. 8, Issue 2, 2018 · pp. 72–78 Read article