Search
1960 articles for “Comparator” (ranking capped at the first 2,000 matches — narrow the search to see the rest)
-
Comparative Study of Symmetric and Asymmetric Oxide Double Gate Junction less FET
Abstract: We carry out the performance of symmetric oxide (HfO2+HfO2) and asymmetric oxide (SiO2+HfO2) n-type junction less field-effect transistor (JLFET) based on two- dimensional Poisson equation. This study is accomplished by simulating a symmetric and asymmetric double gate JLFET on Sentaurus, Technology Computer Aided Design (TCAD) simulator for Silicon (Si) material at room temperature and varying temperature in between 300-360 k.Based on device simulation we find that the asymmetric oxide shows …
Published in Journal of Semiconductor Devices and Circuits · Vol. 8, Issue 2, 2021 · pp. 14–20 Read article
-
Response Spectrum Analysis and Comparison of Seismic Parameters ofLow Rise, High Rise and Asymmetrical RC Structure with and Without Infill for Different Bay Dimensions
Abstract: The concrete block walls or brick masonry are widely used as partitions in world wide. Generally the effect of infill walls is not considered in the design process and istreated as non-structural components. The presence of infill walls has vital role in performance of building during earthquakes. Infill panels significantly increase stiffness and strength of the frames. This study provides the comparative study on summary of performance of low rise …
Published in Journal of Structural Engineering and Management · Vol. 7, Issue 1, 2020 · pp. 1–9 Read article
-
Comparison of RCC and Steel Composite Structure subjected to Static and Dynamic Loads
Abstract: Steel has long been used for the construction projects but the use was limited to a certain height because of the buckling and bending becomes critical after a particular height.The RCC structure after extensive use and research proved to be much more economical and concrete as a construction material covered the whole urban jungle as we witness today. The hustle for the betterment of the construction industry particularly to provide …
Published in Journal of Structural Engineering and Management · Vol. 7, Issue 3, 2020 · pp. 1–4 Read article
-
Comparative Study of Seismic Performance of Multistory Symmetrical RC Frame Structure with and Without Dampers
Abstract: This paper investigates the influence of friction dampers on the nonlinear seismic performance of multistory structure. The operational mechanism of these devices is that a large amount of energy inputting to the structure could be absorbed and the displacement of the structure is reduced. For this purpose, four types of frames are investigated with dampers at different locations. Three types of natural time histories are used for the nonlinear seismic …
Published in Journal of Structural Engineering and Management · Vol. 4, Issue 2, 2017 · pp. 1–5 Read article
-
Comparison of NVC to Different MixedDesign Method of Self-Compacting Concrete
Abstract: In comparison to normally solid vibrated (NVC), Self-compacting concrete (SCC) Elimination of extended properties and compaction due to improving productivity and working conditions. SCC usually NVC is more than powder material and thus to achieve an affordable and durable solid additions to change some of the cement by. As the flow of such recession-self acceptance of compressed concrete characteristics test results; J-ring, funnel and L box are presented. In addition, …
Published in Journal of Structural Engineering and Management · Vol. 3, Issue 3, 2016 · pp. 37–45 Read article
-
Comparative Study of Cold Formed Steel Sections with Hot Rolled Steel Sections
Abstract: Structural steel has become the best alternative for concrete in present construction industry. Hot Rolled steel Sections (HRS) available in market have standard shapes and sizes where as Cold Formed steel Sections (CFS) are produced in various shapes and sizes as per the needs of customer. A comparative study of cold formed sections and hot rolled section with respect to its axial load carrying capacityas a column is attempted. Hot …
Published in Journal of Structural Engineering and Management · Vol. 1, Issue 3, 2014 · pp. 1–4 Read article
-
Comparative Study of RC Elevated Water Tank
Abstract: Designing a water tank requires a good approximation of water demands which is depends on the estimation of population growth rate and design life of the tank and the per capita water consumption rate. Due to rapid increase in urbanization, development activities and enormous need by the public the rate of water consumption increasing day by day. It would difficult task to supply the water directly from the source, it …
Published in Journal of Structural Engineering and Management · Vol. 10, Issue 3, 2023 · pp. 12–19 Read article
-
A Comparative Seismic Assessment of Structures Utilizing Various Angles: Shear Walls vs. Diagrid Structural Systems
Abstract: The diagrid structural system has emerged as a cutting-edge approach to designing tall buildings in recent times. It represents a significant innovation in the construction industry, combining both structural strength and striking architectural aesthetics. The versatility of the diagrid system has led to its widespread adoption in the construction of tall buildings. In-depth research into the design methodology of diagrid structures has unveiled their exceptional structural capabilities and distinctive architectural …
Published in Journal of Structural Engineering and Management · Vol. 10, Issue 2, 2023 · pp. 23–30 Read article
-
Comparative Analysis of Different SRAM Cells Architecture at 70 nm
Abstract: There are severe constraints which affect the real time operation of SRAM cells. With increasing demand of device scaling, the performance parameters of SRAM cells are affected. Our main purpose is to maintain performance of memory cells in real time operation. Here, we considered three basic parameters stability, leakage current and delay for compression of various SRAM cell architectures. In this paper, we considered conventional 6T, asymmetric 7T, asymmetric 8T …
Published in Journal of VLSI Design Tools and Technology · Vol. 8, Issue 2, 2018 · pp. 33–41 Read article
-
Comparative Study of a 32 bit Clock Gated ALU based on Carry Skip Adder and Ripple Carry Adder
Abstract: The ALU is one of the most frequently accessed modules in a CPU and is utilized during most instruction executions. Hence the power consumption of the ALU is a major concern. In this paper a low power 32 bit ALU is designed using VHDL. Lower power consumption is achieved by using clock gating technique than conventional design. A carry skip adder with variable block length is used for the arithmetic …
Published in Journal of VLSI Design Tools and Technology · Vol. 3, Issue 2, 2013 · pp. 6–11 Read article
-
Comparative Analysis of Low-Power Adiabatic Techniques
Abstract: In today’s modern era, new revolutionary designs are replacing old traditional bulky designs. Due to advancements in technology, low-power designs are in demand. Advantages of adiabatic technique can be used for overcoming disadvantages of typical CMOS such as dissipated energy loss. Adiabatic techniques are extremely reliant on parameter changes. In this paper, the merits of adiabatic techniques are depicted on the basis of parameter variations. By the use of SPICE …
Published in Journal of VLSI Design Tools and Technology · Vol. 4, Issue 2, 2014 · pp. 53–58 Read article
-
An Explicit Approach to Compare Crosstalk Noise and Delay in VLSI RLC Interconnect Modeled with Skin Effect with Step and Ramp Input
Abstract: As the technology is acquiring frequency of the Giga-hertz range noise and delay calculations andavoidance of such factors in VLSI interconnects have become dominant to be considered. This paperrepresents a comparison between the crosstalk noise voltage level measured when the RLC on-chipinterconnect was modeled when the skin effect was considered under step input and the crosstalk voltagemeasured when the RLC line was modeled with skin effect under ramp input. In …
Published in Journal of VLSI Design Tools and Technology · Vol. 1, Issue 1-2-3, 2011 · pp. 1–8 Read article
-
Comparative Analysis of Phase Frequency Detector for Phase-Locked Loops
Abstract: This paper presents phase frequency detector using different gates like AND, NOR and NAND and comparative simulation result analysis is carried out. The simulation is carried out using 0.18 μm CMOS process technology with supply voltage 1.8 V. NAND based PFD has lowest power consumption then other and it is 4.2587 µW at 1 GHz Frequency and dead zone to 18 ps which means having approximately zero dead zone problem. …
Published in Journal of VLSI Design Tools and Technology · Vol. 7, Issue 1, 2017 · pp. 18–28 Read article
-
Design, Implementation and Comparative Analysis of Different 8-Bit Multipliers Based on Power, Delay and Hardware Utilization
Abstract: Multipliers play important role in the digital VLSI design. Computational Speed, power consumption, and area are the major parameters on which the performance of the device depends. In digital design, there are different multiplication methods or algorithms. Each algorithm is having its own advantage and disadvantage. In this paper, implementation of five different types of 8-bit multipliers namely Array multiplier, Booth multiplier, Truncated multiplier, Pipelined multiplier, and Vedic multiplier has …
Published in Journal of VLSI Design Tools and Technology · Vol. 10, Issue 3, 2020 · pp. 22–34 Read article
-
Comparison of RSA and ECC Public key Cryptography Techniques in WSN
Abstract: Nowadays, the usage of the wireless sensor networks becomes more advanced and popular. The more these technologies are increasing; there is more necessity for the security mechanisms where the networks have increased diverse. So many security mechanisms solutions are been proposed in the domain of WSN so far and mostly these solutions are usually based on the cryptographic techniques or algorithms. This paper describes two public key cryptography techniques namely, …
Published in Journal of VLSI Design Tools and Technology · Vol. 12, Issue 1, 2022 · pp. 28–35 Read article
-
Comparative Analysis of CMOS CNFET and Memristor Based Full Adder Circuits and CMOS Memristor Based Multiplexer Circuits
Abstract: Continued developments in microelectronics technology have led to a myriad of new compute-intensive applications at the micro-edge, such as artificial intelligence and signal and image processing. Multiplication is a crucial arithmetic process in such applications. However, large logic complexities typically seen in traditional multipliers generate combinatorial blocks with long chains of cascaded carry addition. As such, energy efficiency has remained a primary design challenge for these applications, when powered by …
Published in Journal of VLSI Design Tools and Technology · Vol. 12, Issue 2, 2022 · pp. 22–33 Read article
-
Comparative Physico-chemical Analysis of River Water and Pond Water in Summer Season of Rewa City (M.P.)
Abstract: In this research, we present the study of comparative physico-chemical analysis of River Behar water and Rani pond water of Rewa district, Madhya Pradesh state, India. The variable data of samples are within prescribed limits as suggested by World Health Organization (WHO), Indian standard (ISI) and BIS desirable limit for drinking water for drinking purpose. Yearly variation in physical and chemical parameters like temperature, turbidity, color, odor, taste, pH, total …
Published in Journal of Water Resource Engineering and Management · Vol. 3, Issue 1, 2016 · pp. 42–47 Read article
-
Comparative Study between Conventional and High Strength Concrete
Abstract: The current trend of use of superlatives in concrete technology may strike as somewhat disconcerting to many. We had high strength concrete, hyper-plasticizer, and super plasticizers, very reactive Pozzolana, and now high performance concrete. It is difficult to imagine any concrete being manufactured and used, which is not intended to perform to the extent; high performance concrete is not a new material of construction. The sole distinction is the level …
Published in Recent Trends in Civil Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 47–50 Read article
-
A Comparative Study of Fly Ash Bricks Made with Blend of Clay Brick Waste and Stone Dust
Abstract: The growing environmental concerns and proper disposal of brick waste is a challenge for construction industry. Many research articles support the use of brick waste in construction materials as aggregates. Production of bricks using waste brick aggregate has environmental benefits by lowering the disposal problem and at the same time saving conventional resources. The present work focuses on the utilization of brick waste as a partial replacement of conventional aggregates …
Published in Recent Trends in Civil Engineering & Technology · Vol. 6, Issue 1, 2016 · pp. 60–67 Read article
-
Comparative Study of Geopolymer Paste Prepared from Different Activators
Abstract: The present paper explores the comparative study of the geopolymer paste resulting from different alkali activations. In this experimental study, four series of geopolymer pastes differing in the alkali activation were manufactured by activating low calcium fly ash. These activators were subjected to a certain temperature of 35 °C for duration of 24 h. After casting of the specimens, activated by those activators, they were subjected to 85 °C for …
Published in Recent Trends in Civil Engineering & Technology · Vol. 2, Issue 1-3, 2012 · pp. 9–18 Read article