Search
52 articles for “Peak temperature”
-
Investigation of Dielectric Properties of Lead-Free BaTiO3 Ceramic at Different Sintering Temperatures
Abstract: In the present study, Barium titanate (BaTiO3) was produced using the conventional solid-state sintering technique at three distinct sintering temperatures: 1000, 1100, and 1200°C. It was confirmed by the X-ray diffraction pattern that the perovskite phase was formed without secondary peaks and that the presence of the tetragonal phase was observed near room temperature. Upon conducting a frequency- dependent dielectric study, it was found that ceramic sintered at 1100°C exhibited …
Published in Recent Trends in Fluid Mechanics · Vol. 12, Issue 1, 2025 · pp. 23–30 Read article
-
Heat Absorption and Conversion Thermal Efficiency Analysis on Mass Concrete Embedded Water Pipes as Permanent Roof
Abstract: The solar thermal storage ability of Concrete roof structures was analysed by placing water pipes made of Galvanized pipes embedded inside the top plaster. The performance parameters such as the inlet and outlet water temperatures, ambient temperature and solar radiation has been recorded and indicates positively on embedding this system in to real time roof structures. Studies were carried out at Aluva, South West India (10.1004° N, 76.3570° E). The …
Published in Journal of Thermal Engineering and Applications · Vol. 11, Issue 2, 2024 · pp. 22–27 Read article
-
An Overview on Quantum dot technology in Temperature sensor design
Abstract: Quantumdot (QD) thermometry harnesses the sizedependent electronic structure of semiconductor nanocrystals to translate minute temperature variations into robust optical signals. In this work we present a systematic design framework for QDbased temperature sensors that integrates (i) bandgap engineering through precise colloidal synthesis, (ii) surfacestate passivation to suppress nonradiative pathways, and (iii) a planar photonicreadout architecture compatible with lowcost, CMOSfriendly fabrication. By exploiting the linear redshift of the photoluminescence (PL) peak …
Published in Journal of Electronic Design Technology · Vol. 17, Issue 1, 2026 · pp. 10–17 Read article
-
Egg Quality in Laying Hens: Optimizing Genetic, Nutritional, Environmental and Management Factors for Sustainable Layer Farming
Abstract: This review paper provides a comprehensive analysis of the critical factors affecting egg quality in laying hens, focusing on the integration of genetic, environmental, nutritional, and management practices. Egg quality, including shell strength, albumen consistency, and yolk pigmentation, is a key determinant of both production efficiency and marketability. Genetic factors, such as selection for desirable traits, like shell integrity and yolk color, have a significant impact on the overall quality …
Published in Research and Reviews : Journal of Veterinary Science and Technology · Vol. 14, Issue 2, 2025 · pp. 1–15 Read article
-
Fabrication and Characterization of Almond Skin Powder Reinforced PLA Based Composite Filaments for Fused Filament Fabrication
Abstract: Researchers around the globe are increasingly utilizing recycling methods to address waste generated from polymers, spurred by the dire need to deal with environmental challenges promoting sustainable practices. Polymers are having highly-stable long-chain polymer structure which makes it difficult to degrade easily posing many environmental and health challenges, hence, recycling of the polymers is the sole method to mitigate harmful effects. However, there has been relatively little focus on producing …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 530–539 Read article
-
Interfacial Engineering of Carbon Fiber/Epoxy Laminates Using Functionalized Graphene Nanoplatelets: Experimental and Numerical Study
Abstract: Current research work studies the influence of amines(–NH₂) and carboxyl(–COOH) functionalized graphene nanoplatelets on the mechanical and thermomechanical behavior of unidirectional hybrid composite. Composites having different graphene concentration from 0 to 0.7 wt% were fabricated, characterized and analyzed for multiple testing - tensile testing, dynamic mechanical analysis (DMA) and Fourier transform infrared spectroscopy (FTIR). Tensile testing indicates better elastic modulus and tensile strength due to efficient load transfer between nanoparticles …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 61–77 Read article
-
Electro-chemical treatment of graphite oxide: preparation and Characterization of high quality Graphene material
Abstract: With the enlargement of flexibility and suitability in material industries, high-performance thermal management materials are demanded with high thermal conductivity and electrical insulation are growing. In recent years, graphene has received a numerous focus from science community due to its high thermal conductivity and electrical insulation. Fabrication of light weight graphene and its derivatives as graphene Oxide (GO) and reduced graphene oxide (rGO) via facile processing method is yet a …
Published in Journal of Polymer & Composites Read article
-
Electro-chemical treatment of graphite oxide: preparation and Characterization of high quality Graphene material
Abstract: With the enlargement of flexibility and suitability in material industries, high-performance thermal management materials are demanded with high thermal conductivity and electrical insulation are growing. In recent years, graphene has received a numerous focus from science community due to its high thermal conductivity and electrical insulation. Fabrication of light weight graphene and its derivatives as graphene Oxide (GO) and reduced graphene oxide (rGO) via facile processing method is yet a …
Published in Journal of Polymer & Composites · Vol. 12, Issue 5, 2024 · pp. 25–36 Read article
-
Enhancement of Gas Sensitivity of Composites of Carbon Derived from Rubber Tree and SnO2 to Detect Ethanol Vapor at Room Temperature
Abstract: Films of composites of activated carbon powder prepared from saw dust derived from core of rubber tree (Hevea Brasiliensis) and tin oxide (SnO2) were fabricated using the doctor blade method. Carbon powder was activated using phosphoric acid at 500°C for 45 minutes. The weight ratio carbon/SnO2 varied from 0 to 12% in steps of 2. The structural, optical and morphological properties of films were investigated using XRD patterns, UV-visible spectrums …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 12, Issue 2, 2025 · pp. 31–44 Read article
-
E-World: Battery Management system in E-cycle
Abstract: As e-cycles gain popularity for their eco- friendly transportation and convenience, understanding the dynamics of these key systems is crucial. The report explores various braking mechanisms, such as mechanical and hydraulic disc brakes, and explains their operational principles and safety implications. Additionally, it examines the technologies used for acceleration in e-cycles, focusing on motor types, control systems, and throttle mechanisms. By utilizing the battery management system, we have the capability …
Published in Journal of Alternate Energy Sources & Technologies · Vol. 15, Issue 2, 2024 · pp. 6–11 Read article
-
Structure-Property-Process Relationships in BNNS-Modified PEEK Nanocomposites for High-Performance Applications
Abstract: This study reports the design and performance evaluation of boron nitride nanosheet (BNNS)-reinforced polyetheretherketone (PEEK) nanocomposites fabricated using melt compounding and high-temperature Fused Filament Fabrication (FFF). PEEK, a high-performance thermoplastic, was reinforced with BNNS at 0.5–5wt.% to enhance mechanical, thermal, and tribological functionalities for advanced engineering use. Composite filaments were extruded and printed using a modified Bambu Lab FFF printer. Mechanical testing revealed a peak tensile strength of 108 MPa …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 867–888 Read article
-
Heat Sink-PCM Device for PV Efficiency Improvement
Abstract: This paper is focused on the development of a second stage of a previous work where the PV panel efficiency is improved by using a hybrid system made up of a PCM attached to the rear side of the panel. This evolved stage incorporates a heat sink unit to improve the distribution of the heat removed from the panel; this improvement reduces the elapsed time to reach the steady state …
Published in Journal of Thermal Engineering and Applications Read article
-
On the Relationship between Equivalent Potential Temperature (theta-e) and Convective Rain over Nigeria and Togo
Abstract: Convective precipitation is a key feature of West Africa's climate, driven by the West African monsoon system. Accurate forecasting of convective storms is challenging but essential for disaster mitigation in the region. This study investigates the ability of using equivalent potential temperature (theta-e) for predicting convective rainfall events in West Africa. Theta-e combines the thermodynamic effects of moisture and temperature to represent total energy available for convection. Daily rainfall and …
Published in International Journal of Atmosphere · Vol. 3, Issue 1, 2026 · pp. 26–43 Read article
-
Stretchable Elastomer–PCM Composites with Bluetooth-Enabled Temperature Monitoring for Wearable Healthcare IoT Devices
Abstract: The rapid advancement of wearable healthcare technologies has created a growing demand for multifunctional polymer composites capable of simultaneously providing mechanical flexibility, thermal energy management, electrical conductivity, sensing capability, and wireless communication. In this study, a stretchable elastomer-based polymer composite integrated with a phase-change material and a Bluetooth Low Energy temperature monitoring system was developed for wearable healthcare Internet-of-Things applications. The polymer composite was fabricated using an Ecoflex silicone elastomer …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 · pp. 241–257 Read article
-
Biological Synthesis of Silver Nanoparticles Using Hibiscus Sabdariffa Leaf Extract and It’s Antibacterial Sensitivity Assay
Abstract: In this study, AgNO3 was effectively used to synthesize silver nanoparticles. Hibiscus sabdariffa leaf extract was used to promptly and easily synthesize silver nanoparticles. An UV-Visible spectrophotometer showed absorbance peak in range of 300-600 nm. The procedure was found to be easy to follow, quick, least step and safe for the environment. It is non-toxic, and a viable substitute for traditional physical or chemical procedures. At room temperature, silver ions …
Published in International Journal of Tropical Medicines · Vol. 1, Issue 1, 2024 · pp. 08–13 Read article
-
Enhancing Mechanical and Thermal Performance of M30 Concrete with Carbon Fibre Reinforcement
Abstract: This study examines the influence of carbon fibre incorporation on the mechanical properties of M30-grade concrete. A series of experimental investigations were conducted to assess the effects of varying carbon fibre content on compressive, split tensile, and flexural strengths. The results indicate a significant enhancement in mechanical performance with the inclusion of carbon fibres, with the optimum fibre dosage identified as 0.75%. At this content, the concrete achieved a peak …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 252–260 Read article
-
Investigations of A Solar Dryer With Thermal Storage
Abstract: This study presents the design, building, and performance evaluation of a low-cost mixed-mode natural convection solar cabinet dryer in conjunction with a latent heat thermal energy storage system. The work's goal is to reduce post-harvest losses in rural and semi-urban areas by offering an effective and reasonably priced method of preserving agricultural goods. The dryer is made out of a transparent polycarbonate lid to allow for solar heat gain, an …
Published in Journal of Refrigeration, Air conditioning, Heating and ventilation · Vol. 13, Issue 1, 2026 Read article
-
Exploring The Performance Dynamics of Basalt Fibre Reinforced Polymers: Mechanical and Viscoelastic Insights
Abstract: Basalt fibre reinforced polymer (BFRP) composites are gaining significant attention as sustainable alternatives to traditional reinforcement materials due to their superior mechanical performance, thermal stability, and eco-friendliness. This study examines the tensile, flexural, impact, and viscoelastic properties of BFRP composites fabricated via vacuum-assisted resin transfer molding (VARTM) using varying fibre volume fractions (20%, 30%, and 40%) and fibre orientations (unidirectional and bidirectional). The results reveal that composites with 40% fibre …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 12–22 Read article
-
Smart Monitoring and Controlling of the Battery and Motor
Abstract: The demand for effective battery and motor monitoring and management to guarantee dependability, safety, and peak performance has increased due to the quick development of electric vehicles and smart industrial systems. The smart monitoring and control methods used in battery management systems and motor control systems are thoroughly reviewed in this paper. In addition to speed, torque, efficiency, and fault situations in motors, it emphasizes important characteristics like temperature, voltage, …
Published in International Journal of Electrical Machine Analysis and Design · Vol. 4, Issue 1, 2026 · pp. 11–15 Read article
-
High-Performance Aluminum Matrix Composites Reinforced with Graphene Nanoplatelets a Study on Mechanical and Thermal Behaviour
Abstract: This study investigates the effect of graphene nanoplatelets (GNPs) on the mechanical and thermal properties of aluminum matrix composites (AMCs) fabricated using the powder metallurgy route. Aluminum alloy Al-6061 powder was reinforced with varying GNP concentrations (0, 0.5, 1, 2, and 3 wt%), followed by uniaxial compaction and sintering. The influence of GNP content on the composite’s structural integrity, strength, and thermal behavior was thoroughly evaluated through tensile testing, hardness …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 38–49 Read article