Search
620 articles for “strength properties”
-
Characterization of Mechanical and Viscoelastic Properties of Ceramic Nanoparticle-Reinforced Polymer Composites
Abstract: This study examines the mechanical and viscoelastic properties of polymer composites reinforced with ceramic nanoparticles, specifically focusing on enhancing the performance of the material through the incorporation of alumina nanoparticles. The composites were produced by embedding alumina nanoparticles into an epoxy matrix, and their properties were assessed using tensile, flexural, and dynamic mechanical analyses (DMA). The tensile tests showed a remarkable 40% increase in tensile strength and a 35% enhancement …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 71–82 Read article
-
High-Performance Carbon Nanotube-Reinforced Biodegradable Polymer Composites for Packaging
Abstract: The growing issues concerning the properties of petroleum-based plastics on the environment increased the demand for biodegradable alternatives and polylactic acid (PLA) is one of the most promising options available. However, its poor toughness, thermal resistance, and barrier properties limit broader applications in sustainable packaging. This study reports the fabrication and characterization of PLA-based nanocomposites reinforced with carbon nanotubes (CNTs) at varying loadings (0.1-2 wt.%). Structural analysis (FTIR, XRD) confirmed …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 183–194 Read article
-
Investigation of Mechanical Properties of Hollow Bricks Incorporating Aerated Aggregates: A Polymer-Cement Composite Approach
Abstract: The rapid advancement of construction technologies has necessitated the development of lightweight, thermally efficient, and sustainable building materials. Hollow bricks, due to their inherent voids, offer substantial reductions in dead load and enhanced insulation properties. However, their mechanical performance often falls short when compared to conventional solid bricks. To address this limitation, this study explores the synergistic integration of aerated aggregates and polymer-cement composites (PCCs) in hollow brick production. Aerated …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 92–105 Read article
-
Synthesis and Characterization of Short Fiber Reinforced Biocomposite Materials
Abstract: The fabrication and characterization of a biocomposite reinforced with banana fiber is proposed in this proposal. The substance used for the grid was epoxy. Hand-layup preparation was the last step in the biocomposite's manufacturing. Biocomposites with various fiber and grid compositions were produced. After treating banana strands with NaOH in the composites manufacturing process, a comparative analysis between biocomposites reinforced with treated and untreated filaments was conducted. The antacid treatment …
Published in Journal of Experimental & Applied Mechanics · Vol. 15, Issue 2, 2024 · pp. 42–53 Read article
-
Structure-Property Correlation in PTT/PP Blends with Improved Mechanical Performance
Abstract: The present work investigates a series of poly (trimethylene terephthalate) (PTT)/polypropylene (PP) blends prepared with varying PP concentrations in order to improve the overall performance of PTT, particularly with respect to mechanical properties and processability. PTT is a promising engineering thermoplastic owing to its balanced stiffness, resilience, and chemical resistance; however, its relatively high cost and processing limitations often restrict its wider application. In this context, blending with PP offers …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 90–98 Read article
-
Characterization of Al6082 and Magnesium AZ3lB Composite Produced by The Friction Stir Additive Manufacturing
Abstract: In this modern era, lighter and stronger materials are needed. This is especially true for materials needed in aerospace, robotics, light aircraft, defence, and transportation. When comparison to backbone products in order composite goods have a higher durability & stiffness-to-weight proportion .Most of the newer fabricating methods, called friction stir additive manufacturing (FSAM), uses solid-state drives friction stirring technology to produce bilayer structures by sequentially fusing discrete strata. In this …
Published in International Journal of Manufacturing and Production Engineering · Vol. 1, Issue 1, 2023 · pp. 1–14 Read article
-
Analysis of Bamboo Strength for Structural Material
Abstract: Bamboo is a environmentally accessible available organic plant and among the plants with the quickest growth on earth. It grows up to 60 cm (approx.) a day and it can reach it`s maturity in about four years. It is present in large number of quantities in India. India is of the large producer of bamboo and in every part of India bamboo is easily available. Bamboo has very wide range …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 66–71 Read article
-
Study of the Properties and Destructibility of the Native and Cross-Linked Potato Starch-Filled Polymer Composites for Food Packaging Applications
Abstract: Plastic is a vital component of modern life, commonly used in daily food packaging for its convenience and durability. Plastic marketing bags are manufactured from low-density polythene (LDPE) which causes ecological inconvenience as most of the plastic components are stored in waste and underground conditions for an elongated time. Plastic is a synthetic or semi-synthetic material that does not decompose naturally, and its primary drawback is its environmental impact, prompting …
Published in Journal of Nanoscience, NanoEngineering & Applications · Vol. 14, Issue 3, 2024 · pp. 12–23 Read article
-
A comprehensive study on elemental analysis and sustainable integration of CETP (common effluent treatment plant) sludge as a substitute to sand in concrete
Abstract: This study examines the utilization of sludge from common effluent treatment plants (CETP) as a fractional substitute for sand in M20 concrete mixtures. Its aim is to address disposal challenges associated with CETP sludge while promoting sustainable use of natural resources. The research assesses the structural and microstructural attributes of concrete mixes containing varying percentages of CETP sludge (0%, 10%, 20%, 30%, 40%, and 50%). Tests conducted include compressive, flexural, …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 49–59 Read article
-
Direct Synthetic Routes of MXenes and Their Application in Carbon Fiber Reinforced Plastics (CFRPs) As Supplementary Sizing Layer†
Abstract: Sized carbon fibers with a supplementary sizing layer of MXenes (synthesized via traditional MAX phases), bonded to carbon fibers (CFs) as well as the resin matrix via different kinds of physicochemical (van der Waals force, hydrogen bonding, covalent bonding) interactions enhanced the performance of the resulting carbon fiber reinforced plastic (CFRP) materials. This is because of the strong interface generated due to the appearance of MXene at the interface of …
Published in International Journal of Crystalline Materials · Vol. 1, Issue 1, 2024 · pp. 07–13 Read article
-
Development and Mechanical Characterization of Hybrid Natural Fiber-Reinforced Polymer Matrix Composites for Structural Applications
Abstract: The growing demand for sustainable, lightweight, and cost-effective materials in engineering has driven significant interest in natural fiber-reinforced polymer composites (NFRPCs). Among various options, hybrid composites combining two or more natural fibers offer a balanced improvement in mechanical properties while maintaining environmental benefits. This study investigates the fabrication and mechanical performance of jute–hemp fiber-reinforced epoxy composites. Specimens were prepared using the hand lay-up technique followed by compression molding to ensure …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1181–1189 Read article
-
Utilization of Recron Fibers for Improving Subgrade Stability of Expansive Soils
Abstract: The major interest in the utilization of synthetic fibers is used as reinforcing material for developing reinforcing effect into the entire soil composition laid bellow the structures whare as construction works are going on. Various articles are published on soil reinforcement, yet some of them fibers used are prepared by using with synthetic materials, one type of synthetic fibers were Recron fiber it is used as a reinforcing element to …
Published in Journal of Polymer & Composites · Vol. 12, Issue 5, 2024 · pp. 170–178 Read article
-
Review on Hair Cosmetics on Flaxseeds
Abstract: Worldwide cultivation of flaxseed (Linum usitatissimum), a significant medicinal oil seed crop, is practiced. Flaxseed belongs to the Linaceae family.Because of its biologically active components, which include lignans, dietary fiber, and alpha-linolenic acid, flaxseed has garnered interest as a functional food ingredient recently.Worldwide, Flaxseed is cultivated not only for its oil and fiber but also for its nutritional and potential therapeutic benefits. The dietary fiber present in flaxseed supports overall …
Published in Research and Reviews : A Journal of Ayurvedic Science, Yoga and Naturopathy · Vol. 12, Issue 2, 2025 · pp. 38–46 Read article
-
Stabilization of Reinforced Earth Wall Backfill Using Steel Slag and Recycled PET Fiber: A Composite Material Approach
Abstract: Reinforced Earth (RE) walls are widely used in infrastructure due to their structural efficiency and ease of construction. However, they typically require high-quality granular backfill, which may not be readily available or cost-effective in many regions. This study investigates the potential of utilizing locally available sandy clay soil stabilized with industrial and plastic waste materials specifically 20% steel slag and 0.75% shredded polyethylene terephthalate (PET) fibers, as an alternative backfill …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 110–127 Read article
-
Mechanical Performance Evaluation of Brachyuran Shell Particle-Infused S-Glass Fibre Epoxy Polymer Composites
Abstract: Epoxy composites bio-filled with brachyuran crab shell powder and reinforced with S-glass fibres at different loadings (2%, 4%, and 6%) are tested for their mechanical properties in this work. Using modest amounts of filler significantly improved hardness, ultimate tensile strength, and flexural strength in the empirical data. The largest increase in hardness was 64.42% at 4% filler, up from 26.22% at 2%; however, there was a dramatic decrease to 13.11% …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 500–507 Read article
-
Mechanical Property Assessment of Hybrid Composite Laminates Composed of Jute Glass Fibers in Combination with Flax, Hemp, Sisal and Kenaf Fibers Using the Hand Layup Technique
Abstract: The present work compares the properties of various hybrid composite laminates manufactured using the hand layup technique and addresses their production process, based on glass fiber as the exterior layer and natural fibers (flax, hemp, kenaf, jute, and sisal) as interior layers, in an epoxy resin. Five stacking sequences A-GJJJJG, B-GFJJFG, C-GHJJHG, D-GKJJKG, and E-GJSSJG were used to prepare the test specimens. According to ASTM guidelines, experiments were performed to …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 103–113 Read article
-
Optimization of Direct Ink Writing Process Parameters for Liquid Silicone Rubber/TiO2 Composite Ink
Abstract: The purpose of this research is to develop and optimize the Liquid Silicone Rubber (LSR)/Titanium Dioxide (TiO₂) composite inks in Direct Ink Writing (DIW)-based 3D printing systems. The primary research objective was to use enhancement of mechanical, rheological, and dielectric characteristics of LSR using TiO₂ reinforcement but still retain extrusion stability and dimensional consistency. TiO₂ content (0, 5, 10, and 15 wt%) and catalyst and glycerol ratios were regulated and …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 240–259 Read article
-
Development and Characterization of Antimicrobial Polymer Composites for Food Packaging Applications
Abstract: The increasing demand for sustainable and antimicrobial food packaging materials has led to extensive research in polymer-based composites. This study focuses on developing a polyethylene terephthalate-ethylene vinyl acetate (PET-EVA) composite reinforced with metal oxide nanoparticles (MONs), including Cu₂O, ZnO, and MgO₂. These nanoparticles were selected for their antimicrobial properties and ability to enhance the functional characteristics of the composite. Structural, chemical, mechanical, and barrier properties were extensively evaluated to determine …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 86–93 Read article
-
Process Optimization of Spot Welding for Galvanized Automotive Steel Sheets
Abstract: Resistance Spot Welding (RSW) is a pillar of the modern automotive industry with the usage of lightweight and high-strength products at the highest point of demand. The optimum weld quality of galvanized steel sheets which is a material of choice because of its additional corrosion protective property is however not achieved easily. This study is a well-developed data-based solution to designing the RSW process in the most efficient way, providing …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 32–42 Read article
-
Experimental Investigation of Tensile Strength of Bamboo Fiber/Synthetic Glass Fiber
Abstract: In this work, hybrid fiber reinforced composites (HFRCs) with enhanced mechanical and physical characteristics are created by reinforcing composite laminates using a blend of natural bamboo fiber and synthetic glass fiber. The primary goal of the inquiry is to assess these composites' tensile and impact properties. In comparison to non-hybrid composites, the hybrid composite, which consists of two layers of bamboo fiber and one layer of bidirectional glass fiber, had …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1700–1710 Read article