Journal of Polymer & Composites
Volume 12, Issue 6 (2024)
Table of contents
-
Synthesis And Application of Nano Zinc Oxide in Fabrication of Rubber Composites
Abstract: Nano zinc oxide (ZnO) has garnered significant attention in recent years due to its unique properties and potential applications in various fields. This paper discusses the synthesis of nano ZnO by precipitation method and characterizes them with various techniques such as X-ray diffraction (XRD), Scanning Electron Microscopy (SEM), and Fourier Transform Infra-Red (FTIR) Spectroscopy and explores its application in the preparation of rubber composites. These synthesized particles were measured to …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 1–10 Read article
-
Enhancing Mechanical and Durability Performance of Composite Material Using Egg Shell Powder and Copper Slag.
Abstract: This research aims to investigate the use of copper slag (CS) and Egg Shell Powder (ESP) as partial substitutes in polymer composite to enhance mechanical properties and durability. Considering that the construction sector is recognized for consuming a significant amount of resources in comparison to other industries, its further expansion poses a direct danger to resource availability. This could disrupt ecosystems, lower biodiversity, and have an effect on riverine and …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 1–7 Read article
-
Tribological Study on SiC+Graphene Reinforced Al319 Composite andOptimization of Stir Casting Parameters
Abstract: The aluminium 319 (Al319) is a commonly used material for fabricating automobile components. Due to continuous friction and vibration, those components are subjected to significant wear. Therefore, it is necessary to improve the wear characteristics of this Al319. Hence, in this study Silicon Carbide (SiC) and Graphene nanoparticles (GNPs) are reinforce to Al319 via electro-magnetic stir casting method to optimize wear characteristics without its affecting mechanical properties. Various proposition of …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 105–123 Read article
-
Enhanced Sensitivity Iontronic Pressure Sensor Gauge Using Laser-Created Micro-Pyramid Structures for Wide Linear Range
Abstract: The achievement of high sensitivity, ultrahigh pressure resolution, and great linearity across a wide pressure range under huge pressure preloads remains a challenge despite the substantial development of flexible capacitive pressure sensors. Here we offer an ultrathin ionic layer-integrated microstructure creation process that is configurable. At 1700 kPa, the sensor's linear range sensitivity is 33.7 kPa-1; at 2000 kPa, the pressure resolution is 0.00725%, and the detection limit is 0.36 …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 107–118 Read article
-
Experimental Research on the Strength Properties of Concrete with Recycled Aggregate, Pond Ash, and Rubber Powder Replaced in Part for Concrete Materials in Standard Grades
Abstract: Concrete, a fundamental material in modern construction, poses environmental concerns due to its significant carbon footprint. To mitigate this impact, researchers explore alternative materials like fly ash, GGBS, alcofine, and rubber powder as cement replacements. This study examines the durability and strength of concrete that contains recycled aggregate, pond ash, and waste rubber powder. Waste rubber, abundant from industrial and automotive sources, poses disposal challenges. Pond ash, a byproduct of …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 11–21 Read article
-
Structural, Electrical and Optical Properties of RGO-Incorporated PVA Nanocomposites for UV Shielding Applications
Abstract: Polymer matrix-based nanocomposites reinforced with appropriate nanoparticles have the potential to exhibit improved electrical, optical and mechanical properties, as well as improved UV-shielding capabilities. These materials are currently being utilised for various commercial applications, such as window shields and automotive components. We prepared reduced graphene oxide (rGO)-incorporated polyvinyl alcohol (PVA) polymer nanocomposites employing a solution casting method. XRD and SEM results confirmed that the rGO nanosheets were dispersed well in …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 119–137 Read article
-
Fabrication of Low-Cost and High-Efficiency Crystalline Silicon Solar Cells Using Polymeric Carrier Selective Contacts
Abstract: Crystalline silicon (c-Si) solar cells are the leading choice in the photovoltaic market due to their dependability and long-term stability, but lowering production costs and increasing efficiency remain key issues. Organic semiconductors use carrier-selective contacts based on doped amorphous silicon layers and transition metal oxides to simplify and lower the production costs of efficient crystalline silicon solar cells. Polymers are rapidly being used in photovoltaics as flexible substrates, photoanode films, …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 124–131 Read article
-
Advanced Processing Technologies and Material Properties of Ceramic-Matrix Composites for Structural and Industrial Applications
Abstract: Ceramic-matrix composites (CMCs) are becoming more popular as building and industrial materials because they have a unique set of qualities, such as being able to withstand high temperatures and being light and strong. This brief talks about the newest improvements in processing methods and material features that have put CMCs at the top of the list of industrial materials. Using advanced processing methods like chemical vapor infiltration (CVI), polymer infiltration …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 138–151 Read article
-
Experimental Findings of the EDM Process Parameters for Metal Matrix Composites
Abstract: The process of electrical discharge machining (EDM) shapes hard metals and creates intricately formed, deep holes in a variety of electro-conductive materials by arc erosion. With regard to material removal rate (MRR) in metal matrix composite EDM, this study intends to examine the impacts of operational factors. The material removal rate generated is used to assess the efficacy of the metal matrix composite EDM process. It has been noted that …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 14–18 Read article
-
Parametric Optimization of Biocompatible Ti6AL4V Alloy on Selective Laser Melting for Enhanced Structural Support and Reduced Stress Shielding
Abstract: The Selective Laser Melting technique is widely employed in the production of complexly shaped end products for a range of industries, including biomedical, aerospace, automotive, and defence. SLM is a complicated manufacturing process since a lot of factors influence the characteristics of the items that are printed using it. The SLM printing of fully dense parts is becoming more and more popular for various high-end applications. Because of their biocompatibility …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 143–156 Read article
-
Study of Rehydration and Dehydration behavior of Scolecite by insitu Raman spectroscopy
Abstract: The study of structural changes of stretching and bending modes around 3000-4000cm-1 and 700-1800cm-1 in the temperature range of 299 to 503 K during the dehydration of naturally occurring scolecite was investigated using in-situ Raman spectroscopy. A Raman spectrum from 3000-4000cm-1 was measured for a fibrous zeolite called scolecite to regulate the behavior of water molecules in the passages. The extending vibrations of H2O molecules of scolecite are located between …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 152–159 Read article
-
Solar Light Photocatalytic Degradation of Methylene Blue and Methyl Orange Dyes by Ag-ZnO Nanocomposite
Abstract: A highly efficient silver-assisted ZnO nanocomposite was synthesized using the co-precipitation method, a technique that ensures a controlled and homogeneous formation of the composite material. The high purity of the synthesized nanocomposite was confirmed through detailed FTIR spectra analysis, which showed clear and distinct peaks corresponding to the functional groups present, indicating the absence of significant impurities. To evaluate the photocatalytic capabilities of the nanocomposite, a series of tests were …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 160–171 Read article
-
Use of Geopolymer Composites for Controlling Structural Cracks
Abstract: A building’s safety and stability can be compromised by ignoring the potential structural issues indicated by occurring cracks in buildings. Extensive damage may cause over the period from unidentified cracks.Good quality concrete never cracks in normal service conditions unless high horizontal force is applied. Through the cracks, carbon dioxide is released into the concrete and speeds up carbonation throughout the cracks, thus reducing the structure usage. The materials which are …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 172–184 Read article
-
Materials, Mechanism and Mechanical Properties of Self-curing Concrete: A Review
Abstract: Concrete, a key construction material with high demand for infrastructure development, necessitates an increased water input both during production and curing. This poses a challenge in areas facing acute water scarcity, highlighting the importance of research to reduce water consumption in the process. The process of hydration of the cement within concrete, without outside source, such as water for curing is referred to self curing. Improper curing will cause self …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 185–194 Read article
-
An Overview of Surface Coating Methodologies and Their Use in Technical Materials
Abstract: To safeguard the product or structure against chemical harm, a variety of procedures and materials can be applied in coating applications today. Nowadays, coatings are used extensively in manufacturing all over the world to increase efficiency and reduce expenses two factors that are essential to preserving the sector's profitability. Coated materials have greater strength compared to uncoated materials. A variety of materials, including bio glass, polymers, ceramics, strong and hard …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 19–35 Read article
-
Eco-Friendly Tri-Layer Hybrid Composites: A Sustainable Approach to Polymer Matrix Materials
Abstract: In the current study, we explored the use of environmentally friendly natural fibers such as sisal, banana, and kevlar. These fibers were fabricated by hand lay-up technique, and their impact on tensile and dynamic properties was evaluated according to ASTM standards. The assessment was conducted under both dry and wet conditions, considering two different chemical dosage parameters for comparison. Additionally, the tri-layer fibers underwent two separate chemical treatments using 1% …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 195–205 Read article
-
Analysis of Physical Properties of Polyethylene Terephthalate Coated Aggregates used in Bituminous Concrete Mixes
Abstract: The main cause of climate change that the world has been facing for several years is burning of plastic waste in open air. To contribute to solution of this problem, an investigation was carried out with utilization of plastic waste in bituminous mixtures used in flexible pavement.With varied amounts of Polyethylene Terephthalate (0%, 6%, 6.5%, 7%, 7.5%, and 8%) of asphalt content, variousdesirable properties of aggregates required for bituminous mix …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 206–213 Read article
-
Experimental Evaluation of MDM@Gd2O3:Eu3+ and Protein@MDM@Gd2O3:Eu3+ Functional Nanomaterial
Abstract: Lanthanide cation like Eu3+ (europium Xe 4f66s0) doped functional nanomaterials of lanthanide oxides especially of gadolinium oxide (Gd2O3) as nanorods capped with monodispersed macromolecule (MDM) like polyvinylpyrrolidone (PVP) coated with natural biopolymers like proteins as human serum albumin (HSA) have been the most demanding and applied nanomaterials in areas of the biosensor, optical distinguisher, electronic fluoresces, upconversion, and surface plasmonic resonance (SPR) nanomaterials and others. The Gd3+ and Eu3+lanthanide cations …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 214–223 Read article
-
Formulation and development of Lamivudine Nanoemulsion by using Emulsifying Polymers and It’s Evaluation
Abstract: Nanoemulsion is a novel approach to medicine delivery that helps to increase the bioavailability of drugs that aren’t particularly soluble in water. In this research work, nanoemulsion of Lamivudine was formulated by using polymers such as SPAN 80, TWEEN 80 and Whey protein concentrate with the help of Ultrasonication technology. The formulation was optimized. It was evaluated by assessing pH, viscosity, turbidity, in vitro franz diffusion study, particle size distribution, …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 22–35 Read article
-
Solid Rocket Motor Case: A Review of Existing Design and Composite Material Criteria
Abstract: Solid propulsion systems are an integral part of inaugural vehicles for many space agencies because of their relatively simple design and high reliability. The solid propulsion rocket motor case design, including the material used for fabrication, is an important aspect as it affects the solid rocket motor's performance, reliability, and safety. In this abstract, an attempt has been made to review the most commonly used materials in the manufacture of …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 224–232 Read article
-
Investigation of Chopped Basalt Strands for Concrete Beams Structures
Abstract: The current work unveils a sort of strategy for hacked basalt strands supported for cement footers. The material used to develop the bars are hacked basalt fiber, waterway sand, coarse total and fine total. In this the mechanical and flexure conduct of basalt fiber with differing rate to be utilized to test the crystal and advanced esteem is use to project the pillar. Absolutely six bars is projected out of …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 233–240 Read article
-
Unlocking Synergies: Exploring The Nexus Between Sustainable Building Practices, Green Polymers, and Occupant Health Through SPSS Statistical Analysis
Abstract: This study examines the significance of utilising environmentally friendly polymers in the construction industry, specifically looking at the perspectives of individuals occupying buildings that have used green building design techniques. The focus is on the occupants' perceptions of the efficiency, comfort, and health of the materials used. Green polymers, which are essential for sustainable building, have the potential to completely transform infrastructure development. The materials mentioned include of natural fibre …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 241–252 Read article
-
Mechanical behaviour of Glass and Carbon fiber reinforced composites
Abstract: Components made with fiber reinforced composites are replacing components made with the conventional materials is due to holding superior mechanical properties and high specific strength with good corrosion resistance. These favourable attributes are not possible with a conventional monolithic material. Composites are developed with matrix and fibers as reinforcement material, the reinforcement fibers are playing a crucial role to attain a high strength property. Glass and carbon fibers are using …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 253–257 Read article
-
Stimulation of Plant Growth Promoting Rhizobacteria with ZnO Nanoparticles to Improve Growth and Development of Groundnut Plants (Arachis Hypogaea L.)
Abstract: Rhizobacteria that stimulate plant growth have been extensively utilized as biofertilizers to improve the nutrient content of the soil for various crop plants. In the present study, we have isolated plant growth promoting rhizobacteria (PGPR) for rhizospheric soil of groundnut crops from Gujarat agricultural fields in the Saurashtra region. Fifty-two isolates with particular colony characteristics were obtained from rhizospheric soil. All strain was tested for their plant growth promoting (PGP) …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 253–269 Read article
-
Analysis of Size and Shape Dependence of Thermophysical Properties of Nanomaterials
Abstract: A simple qualitative model, named Qi model which is further extended to Bond energy model has been expressed in terms of melting temperature to explain the shape and size effect on Debye temperature ( ) and Einstein temperature ( ) of nanomaterials. It is known that properties of materials drastically change with size reduction to nanorange and increase in the number of surface atoms with respect to volume of the …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 258–264 Read article
-
Behavioural Study on Synthetic Fibre Reinforced Soil Cement Stabilized Blocks
Abstract: It has been shown that the most prevalent material is soil. It is essential to the manufacture of bricks. It is well known that burned bricks function well for masonry projects, providing durability and structural integrity that are vital for construction applications. Furthermore, a significant amount of heat energy is utilized during the heating process that creates them, thus emphasizing the energy-intensive nature of brick production. In addition, children are …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 265–292 Read article
-
Ranking of Epoxy/Kota Stone Dust/Fly Ash Composite Using Integrated AHP-TOPSIS Approach
Abstract: The generation of industrial waste is a significant contributor to environmental pollution. The stone industry is no exception to this, and it is known to produce a significant amount of waste. The Kota Stone Industry in India is one such industry that generates waste. This research article focuses on composite material selection for mechanical and structural applications by fabricating epoxy composites reinforced with Kota stone dust and fly ash using …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 36–42 Read article
-
Developing Food Packaging with Nanomaterials: In-Depth Examination based on Electromagnetic and Optical Radiations
Abstract: Problems with food degradation, infection, and environmental compatibility are driving constant innovation in the food packing sector. Nanomaterials (NM) are investigated as possible solutions to the problem to improve the effectiveness of food packaging by means of their exceptional optical and electromagnetic characteristics. Several factors, such as the need to analyze capacity, cost-effectiveness, and possible environmental implications, prohibit the use of NM in food packing. This review summarizes the optical …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 36–44 Read article
-
Tb3+ activated Boro Phosphate Glass: Synthesis and Photoluminescence (PL) Characteristics
Abstract: The (40B2O3+ 3Al2O3+(10-x) P2O5 + xTb + 7ZnO+5LiCO3+ 10H6NO4P+25SrCO3) boro phosphate glass was successfully synthesized via melt quenching method. The structural confirmation is supported with X-ray diffraction (XRD) data and surface morphology was defined by scanning electron microscope (SEM). The (40B2O3+ 3Al2O3+(10-x) P2O5 + xTb+ 7ZnO+5LiCO3+ 10H6NO4P+25SrCO3) boro phosphate glass has been investigated for its Photoluminescence (PL) under UV excitation. At 544 nm, the excitation was observed, and at 222 …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 43–47 Read article
-
Synthesis, Characterization and Antibacterial Evaluation of Novel Canola Oil-Based Poly-(Citrate/Succinate)-amide Incorporated with Zn (II) and Ni (II) Metal Ions
Abstract: This present research study is to fabricate efficient metal-incorporated Canola oil (CO) polymers synthesised using dicarboxylic acids – Citric acid (CA) and Succinic acid (SA). The research mainly highlights the fabrication of polymeric materials using CO via a safer chemical synthesis route with less toxic reactants and minimal solvent/diluent to accomplish sustainability, adopting the green chemistry principle. Divalent Zinc (Zn) and Nickel (Ni) were incorporated in the poly-(Citrate/Succinate)-amide matrix, Ni …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 45–69 Read article
-
SYNTHESIS AND CHARACTERIZATION OF Mn2+ DOPED LiPbX3(X = Cl, Br, I)
Abstract: In this paper the structural, electronic and optical properties of Mn doped Pb based cubic perovskites LiPbX3(X= Cl, Br and I) were studied by wet chemical method (sol gel method). For Mn doped LiPbX3(X= Cl, Br and I) NCs, MnCl2 and PbBr2 were added in molar feed ratio 1.35 mole% and nan crystal were examine with the help of TEM and their structure were confirmed by X-ray diffraction (XRD). Additionally, …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 48–54 Read article
-
Synthesis and Study of Photoluminescence properties of Sm3+ activated 7TiO2 + 3Al2O3 + (60-x)B2 O3 +xY+ 5LiCO3 +25SrCO3 Borate Glass for SSL Applications
Abstract: Melt quenching was used to successfully create the raddish orange light-emitting Sm3+activated 7TiO2 + 3Al2O3+ (60-x) B2O3+xY+ 5LiCO3+25SrCO3 (X=0.001, 0.002, 0.005, 0.01 and 0.02, Y=Sm3+) borate glass. XRD examination confirmed the phase of the prepared Un-doped and Doped 7TiO2 + 3Al2O3+ (60-x) B2O3+xY+ 5LiCO3+25SrCO3 glass. Its PL characteristics under ultraviolet (UV) light (302-468 nm) were later studied. At 602 nm, the excitation was detected, and at 402 nm, the emission. …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 55–60 Read article
-
From Carbon to Composites: Evolution and Trends in Supercapacitor Technology
Abstract: Supercapacitors, also referred to as ultracapacitors, have become a crucial component in the landscape of energy storage technologies. They effectively bridge the gap between conventional capacitors and batteries, offering unique advantages such as high power density, rapid charge/discharge rates, and exceptional cycle life. These characteristics make supercapacitors indispensable for a wide range of applications, including consumer electronics, automotive systems, and renewable energy systems. This comprehensive review explores the evolution of …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 61–67 Read article
-
Recent Advances in Transition Metal Complexes with Phenyl Acetic Acid and Pseudo Halogen: Synthesis, Characterization and Applications
Abstract: A well established strategy is to introduce a biologically relevant organic molecule in coordination sphere of transition metal complexes to increase the selectivity and biocompatibility. Phenylacetic acid (PAA), an organic molecule with a phenyl functional group and a carboxylic acid functional group, is a phenylalanine that is generated from the naturally occurring auxin, which is extensively present in plants. The most promising outcomes in the battle against cancer and microbes …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 68–78 Read article
-
Commercialization of Smart Polymers in Advanced Composite Structures for Industrial Applications
Abstract: The commercialization of smart polymers in advanced composite structures represents a significant rise in material science, particularly for industrial applications. These smart polymers show unique properties such as self-healing, shape memory, & responsiveness to environmental disturbances, making them ideal for a wide range of applications. In this paper, the researcher explores the advancements in developing and applying smart polymers within composite structures, focusing on their potential. Revolutionize industries like atmosphere, …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 70–81 Read article
-
Enhancement of Soil Fertility Using Natural Fiber-Based Engineering Composite Materials for Higher Crop Production: A Review Paper
Abstract: Enhancement of Soil fertility using engineering composite materials via efficient nutrient management strategies is essential as is rising natural fiber based composite material crop production every land area unit to satisfy next diets and fiber consumption. Major developments have improved the production's nutrient-use economy Improved crop flexibility to applied nutrients, decreased off shore nutrient move, and greater predictions of the nutrients available to plants in the root zone have all …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 79–87 Read article
-
An Experimental Investigation of Machining Parameters on Aluminum Composites
Abstract: The need for a material with good mechanical, thermal, and wear resistant properties is satisfied by aluminum composite. However, the biggest obstacle to substituting it with alternative materials is the machining challenges. For this kind of hard-to-cut material, electric discharge machining is a very efficient method. Thus, using a Taguchi-based method, an attempt has been made to determine the most advantageous amount of input parameters for EDM of Al composite. …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 8–13 Read article
-
An Experimental Investigation on Surface Roughness of Laser Beam Machining of Aluminium Alloy
Abstract: Laser beam machining (LBM) is a cutting-edge technique widely utilized for precision machining of advanced materials. This experimental investigation focuses on the surface roughness of aluminum alloy (Al 6061) during LBM. The study systematically examines the impact of process parameters such as laser power, cutting speed, and gas pressure on surface roughness (Ra). The significance of surface roughness in determining the quality and functionality of machined components is emphasized. The …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 82–104 Read article
-
Investigation of Electronic Transport in Li2O and ZnO Nanoparticles Containing Polypyrrole Systems
Abstract: Polypyrrole systems having nanocrystalline ZnO and Li2O with different compositions (PPy50 + Li2Ox + ZnO(50-x), where x = 0, 2, 4, 6, 8, and 10) have been produced by ball milling. compositions of the type The temperature-dependent DC conductivity of each sample was determined in the temperature range of 313 K to 363 K. The conductivity studies show that Polaron hopping was the conducting mechanism in the material composites. The …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 88–95 Read article
-
Review and Opportunities for Thermal examination approaches Used to Investigate the Thermal Properties of Composite Compounds
Abstract: The use of thermal examination approach to assess the thermal quality of energy materials in “China” is concisely described. They are often used to calculate thermal stability, compatibility, and thermophysical constants, as well as to study thermal breakdown kinetics, causes, and interactions. Furthermore, a few studies focused on creativity or advancement, such as analyzing the mechanisms of topochemical reactions, assessing condensed-phase reaction kinetics by tracking the change in functional groups …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 96–106 Read article