Sand
9 articles · search the full text for this term
-
Impact of Mould Material on Microstructure and Mechanical Properties of Aluminium Castings: A Comparative Study with Aluminium Matrix Composites
Abstract: Casting has a wide industrial usage because it allows manufacturing complicated forms even at a comparatively low cost. Issues like transfer of heat through the interface of the mould and the metals, the rate of solidification, and the characteristics of the mould material have a powerful impact on the quality of cast products. This study measures the influence of various mould substances on the mechanical characteristics of aluminium castings. Sand, …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 9–18 Read article
-
Production of Floor Tile Using Recycle Low Density Polyethylene And Groundnut Shell as a Filler
Abstract: The production of flow tile using recycled low density polyethylene and groundnut shell as filler with the particle size of 120µm was carried out in this project . 10 pphr of all the fillers were weighed and mixed with recycled low density polyethylene on two roll mill machines. The result on this work showed that on FTIR five functional groups were identified and they are; OH, C-H, CH2/CH3, C-O, C=H. …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 11, Issue 1, 2024 · pp. 1–9 Read article
-
Mining of the River Bed and Environmental Consequences
Abstract: Due to tremendous rate of demand, by the year 2050, the world is expected to run out of construction grade sand. Construction-grade sand is found in aquatic environments, such as rivers and is a provisioning ecosystem service. Even under controlled circumstances, the practice of extracting the sand from the riverbed and river-banks impacts the environment. Unfortunately, many countries lack sand mining regulation policies and in combination with a high demand, …
Published in Journal of Water Pollution & Purification Research · Vol. 10, Issue 3, 2023 · pp. 24–33 Read article
-
Assessing the Permeability of Bentonite with Sand, Marble Dust, and Fly Ash mixture with and without Effect of Permeate Solution for the Development of Efficient and Cost-Effective Landfill Liner for Sustainable Waste Management and Environmental Preservation
Abstract: This exploration paper researches the capability of further developing landfill liner materials by integrating varying percentages of bentonite into sand, marble dust, and fly ash mixtures. The study focuses on determining whether these mixtures are suitable for development of landfill liner by examining their permeability properties. Bentonite, a clay known for its high swelling and sealing properties, is added to sand, marble dust, and fly ash at different range from …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 1–11 Read article
-
Exploring Lightweight and Earthquake-resistant Construction with Ferrocement Sandwich Panels
Abstract: The creation of sandwich panels made of ferrocement as non-load-bearing building components is examined in this study. The sandwich panels had one layer of wire mesh netting between two thin pieces of ferrocement for reinforcement. Two thin ferrocement layers strengthened with a thermocol sheet made up the sandwich sections. The two iron lattice sections were connected by steel wires. Three sandwich panels in total were made. Compared to traditional masonry …
Published in Recent Trends in Civil Engineering & Technology · Vol. 13, Issue 1, 2023 · pp. 1–6 Read article
-
Bearing Capacity of Double Box Shaped Skirted Footings on Sand
Abstract: The double-box-shaped footing with and without skirt and sand-resting pressure settlement behavior was discussed in this paper. Different parameters are normalised skirt depth (0.25 to 1.5), relative sand density (30 to 60 percent) and sand footing interface state (partially rough and rough). Results of this study showed that a general and local shear failure was observed at a relative density of 50 percent and 60 percent, and 30 percent and …
Published in Journal of Geotechnical Engineering · Vol. 8, Issue 3, 2021 · pp. 10–19 Read article
-
Development of Low Cost- eco-friendly and Pathogen Free Water Purifier
Abstract: The process of removing unwanted physical and chemical pollutants from water is known as water purification. Water purification system proposed in this project focus on providing eco-friendly pathogen free water at low-cost Various methods for water filtration are available, but they are not economically viable for rural residents. The proposed system is made up of a mix of natural materials such as sand, coarse aggregate, and chemicals. It's a good …
Published in Emerging Trends in Chemical Engineering · Vol. 8, Issue 2, 2021 · pp. 14–18 Read article
-
Partial Replacement of Sand and Cement by Iron Ore Slime for Concrete Building Material
Abstract: Iron ore slime is a waste material generated after beneficiation of iron ores. It causes air, water and land pollution. From resource conservation point of view, the recovery of iron values is important and their use in different application. Researchers are also trying to find out value-added alternative application of iron ore slime rejects. In this paper, iron ore slime was used in concrete building material and evaluated the partial …
Published in Recent Trends in Civil Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 37–42 Read article
-
Effect of Alccofine and Tyre buffings on Engineering Properties of Sand
Abstract: In the present paper, the effect of alccofine and tyre buffings addition on the compression and bearing ratio of sand are evaluated through laboratory study. On the basis of compaction test, a reference mix composed of sand + 12 % alccofine + 2 % tire buffing was selected for further study. The unconfined compression and bearing ratio test on the reference mix was then carried out by curing the sample …
Published in Journal of Geotechnical Engineering · Vol. 7, Issue 1, 2020 · pp. 9–20 Read article