Search
55 articles for “sinter”
-
Characterization and Mechanical Behavior of Sintered Al-Mg Powders
Abstract: The resolution of the work is to relate the characterization and mechanical properties for argon atomized Al-1wt%Mg powders through and not through lubricant 1 wt% graphite. Pure nitrogen sintering was accomplished and the effect of sintering atmosphere for the mixed Al-1%Mg powder compacts was examined. One weight percent graphite was premixed with the powder as a lubricant for the first set samples. However, no graphite was used for the second …
Published in Trends in Machine design · Vol. 6, Issue 1, 2019 · pp. 1–7 Read article
-
Exploration of Mechanical Characteristics and Microstructural Analysis of Copper Matrix Composites with Hybrid Reinforcements via Muffle Furnace Sintering
Abstract: Metal Matrix Composites (MMCs) have drawn a lot of interest in the area of innovative materials because of how widely they may be used. Due to their extraordinary qualities, such as high thermal conductivity, higher temperature endurance, improved corrosion resistance, and great weldability, copper matrix composites stand out among them. These qualities make them desirable and promising materials for uses including heat exchangers, automotive parts, and electrical components. In this …
Published in Journal of Polymer & Composites · Vol. 11, Issue 12, 2023 · pp. 119–126 Read article
-
Effect of Bi2O3 Content and Sintering Temperature on the Frequency-Dependent Magnetic Properties of Nanosized Barium Hexaferrite
Abstract: The magnetic properties of commercially available nanosized barium hexaferrite (BaFe12O19) are studied. The particles were characterized using X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and high-frequency magnetic measurements. The frequency-dependent magnetic properties viz. complex permeability and loss tangent were analyzed within the 10 MHz to 1 GHz range. Variations in complex magnetic permeability and loss tangent were discussed under varying sintering parameters such as temperature and sintering aid content. The …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 107–113 Read article
-
Adoption of Heat Recovery Technology in Sintering Process to Reduce Carbon Imprint
Abstract: India is the second largest steel producer in the world after China. The 2017 National Steel Policy of India set out the ambitious plan of 250 MT steel production and per capita consumption to around 160 kg by 2030. The dominant iron-making route is blast furnace (BF), which is an energy-intensive process based on fossil fuel consumption. The steel industry contributes around 7% of all greenhouse gas (GHG) emissions. India …
Published in Journal of Materials & Metallurgical Engineering · Vol. 12, Issue 3, 2022 · pp. 38–44 Read article
-
Modeling of Sintering Process for the Preparation of Magnetic Abrasives by RSM and ANN Models
Abstract: In this study, a modeling has been done for the prediction of the sintering process, as sintering process is one of the best processes to prepare magnetic abrasives. The sintering process is modelled by using RSM and ANN techniques. The ANN model has been developed using a multilayer feed-forward neural network and trained with the help of an error backpropagation learning algorithm based on the generalized delta rule. The indication …
Published in Journal of Experimental & Applied Mechanics · Vol. 10, Issue 3, 2019 · pp. 5–12 Read article
-
Deformation and Densification Behaviour of Sintered Aluminium Alloy and Chromium Carbide Metal Matrix Preforms
Abstract: This paper presents comprehensive experimental results focused on the deformation and densification behavior of sintered AA2618 - 2% Cr3C2 metal matrix preforms. The study specifically examines preforms with varying aspect ratios subjected to a cold upsetting process. To create the powder preforms, an initial theoretical density of 89% was achieved using a cylindrical die on a 600 kN hydraulic press. The sintering process was conducted in an electric muffle furnace, …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 125–131 Read article
-
Investigation of Dielectric Properties of Lead-Free BaTiO3 Ceramic at Different Sintering Temperatures
Abstract: In the present study, Barium titanate (BaTiO3) was produced using the conventional solid-state sintering technique at three distinct sintering temperatures: 1000, 1100, and 1200°C. It was confirmed by the X-ray diffraction pattern that the perovskite phase was formed without secondary peaks and that the presence of the tetragonal phase was observed near room temperature. Upon conducting a frequency- dependent dielectric study, it was found that ceramic sintered at 1100°C exhibited …
Published in Recent Trends in Fluid Mechanics · Vol. 12, Issue 1, 2025 · pp. 23–30 Read article
-
A Study on the Sintering Behavior of Al2O3/Y2O3 Doped ZrO2 Composites
Abstract: AbstractZirconia ceramics are widely used as cutting tools due to their very high hardness, excellent fracture toughness, flexural strength, and wear-resistance properties. Tetragonal zirconia exhibits better mechanical properties due to the transformation toughening of zirconia. The superior mechanical properties in zirconia are mainly due to higher density and controlled microstructure. In the present work, an attempt has been made to prepare near full-dense zirconia bodies with controlled microstructure by optimizing …
Published in Journal of Polymer & Composites · Vol. 2, Issue 1, 2023 · pp. 1–8 Read article
-
A Review on Materials and Working Process Parameters of Selective Laser Sintering
Abstract: The potential for additive manufacturing technology to replace some of the current conventional manufacturing methods makes it one of the research and development fields that is expanding quickly. With additive manufacturing, three-dimensional physical models are produced layer by layer from computer-aided design (CAD) models. Fully dense metal things may be produced more rapidly and accurately with additive manufacturing. The Selective Laser Sintering (SLS) procedure uses powder bed fusion, in which …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 522–529 Read article
-
Stabilization of Heavy Metal Sludge to Pass the TCLP Test Using Cement with a Sinter as a Additive
Abstract: According to the U.S. Stabilisation is the best-proven technology now in use, according to the Environmental Protection Agency's definition in Title 40, Part 268 of the Code of Federal Regulations (40 CFR 268).This method prevents harmful contaminants from leaking into the environment by physically and chemically trapping them all in a matrix. The investigations used 15 different water-mixed combinations of cement, fly ash, sinter, and lime. The study also examined …
Published in Journal of Polymer & Composites · Vol. 11, Issue 10, 2023 · pp. 16–24 Read article
-
An Investigation into the VariablesInfluencing the Densification of Spark Plasma Sintered, 40 Weight Percent Ni-Fe Nano Powder
Abstract: The mechanical alloying process that included high-energy ball milling resulted in particle sizes of 25 mm and 80 mm on average for the Ni-Fe alloy that included 40 percent Ni. At room temperature, highenergy planetary ball milling was carried out over timespan ranging from 15 hours to 60 hours. All of the samples were sintered at the same conditions, which included a temperature of 650 degrees Celsius and a pressure …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. 29–35 Read article
-
Behaviour of NINL Blast Furnace with 100% Calibrated Lump Iron Ore
Abstract: A relation between sinter usages in burden and productivity are well established. Now a day, almost all blast furnace usages a sinter in its burden charge. The percentage of sinter in blast furnace is depending upon the availability of fines & sinter machine. But some time, due to non-availability of fine or sinter machines, or both, only calibrated iron ore lump are used as a source of iron in charge …
Published in Journal of Materials & Metallurgical Engineering · Vol. 1, Issue 1-3, 2011 · pp. 28–36 Read article
-
`Lining Pains and Lance Strains-A Case Study to Competing Productivity
Abstract: A relation between sinter usages in burden and productivity are well established. Now a day, almost all blast furnace usages a sinter in its burden charge. The percentage of sinter in blast furnace is depending upon the availability of fines & sinter machine. But some time, due to non–availability of fine or sinter machines, or both, only calibrated iron ore lump are used as a source of iron in charge …
Published in Journal of Materials & Metallurgical Engineering · Vol. 1, Issue 1-3, 2011 · pp. 48–60 Read article
-
Fabrication and Multi scale Characterization of Functionally Graded Composites Reinforced with Hybrid Ceramic–Metallic Phases
Abstract: Using composite materials as functionally graded composites (FGM) can improve its excellent material properties. In this work, magnesium peroxide, silicon carbide, and aluminum are used to create four-layer FGMs. The sintering process, which blends the particles of each material using a powder methodology, has been used to complete the fabrication process. Three factors, including sintering time, sintering temperature, and compacting pressure, are taken into account when fabricating FGM. The FGM …
Published in International Journal of Mechanical Dynamics and Systems Analysis · Vol. 3, Issue 2, 2025 · pp. 1–11 Read article
-
Low-Velocity Impact Behaviour of 3d Printing Techniques Using Fiber Reinforcement Polymer Composites: A State of the Art Review
Abstract: Additive manufacturing (AM) is one of the pioneering fields of composite manufacturing, not only in the fabrication of composite all other emerging fields also utilize this technology. Fibers are one of the predominant reinforcing agents which are used to fabricate composite materials for many applications. This review article provides a detailed discussion about the role of 3D printing technology using fiber-reinforced composites in low-velocity applications. 3D printing technology provides very …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 8, Issue 2, 2021 · pp. 1–7 Read article
-
Microstructural Design and Functional Properties of Polycrystalline Materials
Abstract: Polycrystalline materials, composed of an aggregate of crystallites or grains, are foundational to modern engineering applications due to their versatile functional properties. The microstructural design—encompassing grain size, shape, orientation, phase distribution, and grain boundary characteristics—plays a pivotal role in determining mechanical, thermal, electrical, and magnetic behavior. This abstract explores the intricate relationship between microstructure and functionality, emphasizing how tailored processing techniques such as thermomechanical treatments, sintering, and additive manufacturing can …
Published in International Journal of Crystalline Materials · Vol. 2, Issue 2, 2025 · pp. 16–20 Read article
-
Investigating The Influence of Sic Reinforcement on The Mechanical and Tribological Properties of PA12 Polymer Composites in SLS
Abstract: The study investigates the mechanical and tribological performance of neat PA12 polymer and SiC-reinforced PA12 polymer composites made via Selective Laser Sintering (SLS). To evaluate just how reinforcement has influence upon overall performance, we incorporated into the PA12 polymer matrix a constant amount of 5 wt.% of Silicon Carbide (SiC). Mechanical testing focused on both tensile and fatigue behavior and testers conducted it with a Servo-Hydraulic Multipurpose High-Capacity Fatigue Test …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 541–554 Read article
-
Analysis of Ageing and Degradation Behavior of Polyamide-12 for Sustainable Additive Manufacturing
Abstract: Additive Manufacturing (AM), particularly High-Speed Sintering (HSS), has emerged as a transformative technology capable of producing complex thermoplastic parts with high efficiency and minimal material waste. The HSS process involves selective deposition of radiation-absorbing ink followed by infrared heating to consolidate polymer powders-most commonly polyamide-12 (PA12). While PA12 is widely used due to its excellent thermal stability and mechanical properties, the sustainability of HSS strongly depends on the reuse of …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 136–154 Read article
-
Influence of SlS Parameters on Strength and Fatigue Durability of Polyamide-12
Abstract: Selective Laser Sintering (SLS), a laser-based polymer powder bed fusion process, has gained prominence in the fabrication of high-performance thermoplastics such as Polyamide-12 (PA12). This paper provides an extensive review of how key SLS process parameters—such as laser power, scan speed, hatch spacing, and energy density—affect the mechanical properties of PA12 components, with a specific focus on tensile strength and fatigue resistance. Studies demonstrate that increasing energy input enhances particle …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 178–191 Read article
-
Comparative Investigation on Mechanical Properties of AMCs Fabricated through Liquid and Solid-State Fabrication Process
Abstract: This current research work is primarily focused on comparative experimental study on effect of two distinct fabrication process routes i.e. liquid state and solid state process and their corresponding parameters on microstructure and micro-hardness properties of Aluminium matrix composites (AMCs). In this work, AMCs were fabricated by reinforcing Al2O3 powder materials of 5, 10 and 15 wt.% into pure Aluminum (Al) matrix phase through two distinct processes; liquid state (stir …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 202–215 Read article