Search
111 articles for “modulus reinforcement”
-
Evaluation of Short-Term Fatigue Characteristics and Measurements of Modulus Reinforcement of Cement-Polypropylene Composite Material
Abstract: The choice of filler materials along with the derived composition of constituents plays an important role in determining the performance effectiveness of polymeric composite material. This work is an annexure of vivid experimental study succeeding with the evaluation of fatigue characteristics together with the determination of reinforcement and modulus-of-elasticity of cement reinforced polymeric composite material. Inexpensive fly-ash based Portland pozzolana cement is used as filler material with the polypropylene as …
Published in Journal of Mechatronics and Automation · Vol. 4, Issue 1, 2017 · pp. 31–41 Read article
-
Resilient Characteristics of Modified Subgrade Soil
Abstract: AbstractThe problems with poor subgrade soil which is considered as the foundation for the flexible pavement regarding the deformation under load repetitions is a major concern for road engineers. The Poor subgrade soil may be improved by stabilization or implication of soil reinforcements. In this work, the pneumatic repeated loading testing techniques has been implemented for assessing the influence of both techniques on the resilient characteristics of subgrade soil. Cutback …
Published in Trends in Transport Engineering and Applications · Vol. 4, Issue 3, 2017 · pp. 28–37 Read article
-
The Mechanical Properties of Manganese Chloride Salt Reinforced [PVA: PVP] Blend Films
Abstract: In this study, pure [PVA: PVP] polymer blend film and MnCl2·4H2O salt reinforced polymer blend films at different weight ratios (10–50) wt%) were prepared by using the casting method. The effect of salt weight ratio on the mechanical properties of the [PVA: PVP] polymer blend films reinforced by MnCl2·4H2O salt was also studied. The experimental results obtained from the tensile test of the [PVA: PVP] polymer blend films reinforced by …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 8, Issue 2, 2021 · pp. 16–23 Read article
-
Solar-Responsive Photo-Thermal Polymer Composites with Carbon Nanostructures for On-Demand Water Purification
Abstract: The development of solar-responsive polymer nanocomposites offers a sustainable pathway for water purification. In this work, polyvinyl alcohol (PVA) films reinforced with graphene nanoplatelets (GNPs) and multi-walled carbon nanotubes (MWCNTs) were fabricated and systematically investigated for their mechanical, thermal, viscoelastic, and thermal transport properties. Neat PVA displayed moderate tensile strength (~38 MPa) and high elongation (~165%), whereas 1.0 wt% nanofiller loading enhanced tensile strength to ~52 MPa and modulus to …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 199–209 Read article
-
Perspectives of 3D-Printed Polylactic Acid-Based Composites Reinforced with Natural Fibers
Abstract: The growing demand for sustainable and biodegradable materials has led to the development of polylactic acid (PLA)-based composites reinforced with natural fibers. This study investigates the mechanical, thermal, printability, and environmental performance of 3D-printed PLA/Natural Fiber composites, addressing key challenges in fiber-matrix compatibility, structural integrity, and biodegradability. Natural fiber reinforcement enhanced Young’s modulus and flexural strength, but excessive fiber content led to agglomeration, reduced tensile strength, and increased brittleness. Thermal …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 649–664 Read article
-
Acalypha Indica Root Fibre in Polymer Composite: Mechanical Characterization
Abstract: The mechanical characteristics of Acalypha Indica root fibre reinforced epoxy resin composites, including tensile strength, tensile modulus, percentage of elongation, flexural strength, and impact strength, were studied. Composites were fabricated using epoxy glue and randomly oriented fibres of 3 mm length in varying weight ratios of 10%, 20%, 30%, and 40%. The hand layup method was followed by compression moulding to construct the composites. The study aimed to determine the …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 512–522 Read article
-
Production of Injection Moulded Natural Fiber Reinforced Hybrid Composites and Assessment of Hybridization’s Effect on Mechanical Properties
Abstract: Over the past two decades, rising environmental awareness, public concern over waste, and stricter government regulations have encouraged companies to reduce their reliance on petroleum-based fuels and products. Consequently, there is a clear need to find sustainable, eco-friendly substitutes for the materials currently in use. This shift has renewed attention on renewable resources and sparked wider interest in advanced composites and green materials research. With this in mind, the present …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 246–271 Read article
-
Structure–Property Relationships in Poly (N isopropylacrylamide) Hydrogels: Toward Thermoresponsive Polymer Composites
Abstract: Poly(N-isopropylacrylamide) (PNIPAAm) hydrogels can shift from solid to gel and back again at body temperature. Due to their lack structural integrity, thermal stability, and mechanical strength, they are difficult to use. This study mixed PNIPAAm with biocompatible fillers like chitosan and silicon nanoparticles to create hydrogels with superior structure-property correlations. Free radical polymerization with ammonium persulfate/TEMED initiator and N,N′-methylenebisacrylamide crosslinker produced the composites. Scanning electron microscopy showed a denser, interconnected …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 884–895 Read article
-
Synthesis of Glass Fiber Reinforced Polymer Composites Incorporating MWCNTS and Graphene: A Study on Dynamic Mechanical Behavior and Cole–Cole Representation
Abstract: Glass fiber reinforced polymer (GFRP) composites were fabricated using multi-walled carbon nanotubes (MWCNTs) and graphene as nanofillers through the hand lay-up technique. Two sets of composites were prepared by incorporating MWCNTs and graphene separately into the epoxy resin matrix at varying weight percentages (2%, 4%, 6%, 8%, and 10%). Mechanical and viscoelastic properties were evaluated following ASTM standards, and Dynamic Mechanical Analysis (DMA) was performed to study their mechanical and …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1411–1403 Read article
-
Mechanical Properties of Tri Sustainable NBR/Cement Waste/Rice Husks Silica Blend
Abstract: AbstractThe accumulation of agricultural and industrial manufacturing waste is an important environmental problem of the most countries in which the means of recycling these waste are not available. Therefore, it is important to find sustainable green engineering applications for the integration of these wastes in the industry and be an environmental, economic and industrial competitor and alternative to materials existing now. Cement waste and rice husks silica were added as …
Published in Journal of Polymer & Composites · Vol. 5, Issue 1, 2017 · pp. 29–31 Read article
-
Marine Algal Microfiber and Agro-Waste Reinforced Crosslinked Polymer Composites for Sustainable Coastal Materials
Abstract: Crosslinked bio-polymer composites reinforced with marine algal microfibers and agro-waste fillers were fabricated and systematically characterized for sustainable coastal applications. Mechanical testing revealed that tensile strength increased from 18.5 MPa for neat polymer to 25.1 MPa at 20 wt.% reinforcement (~35% improvement), while the flexural modulus improved from 0.72 GPa to 1.02 GPa (~42% increase). Impact strength, however, decreased from 3.8 kJ/m² for neat polymer to 2.9 kJ/m² at 30 …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 210–223 Read article
-
Processing and Mechanical Characterization of Compression-Molded Ultrahigh Molecular Weight Polyethylene Biocomposite Reinforced with Aluminum Oxide
Abstract: Ultrahigh molecular weight polyethylene (UHMWPE) has been widely used as a bone implant material in orthopedic surgical applications in trauma due to its low coefficient of friction, good biocompatibility, and excellent wear and corrosion resistance properties in comparison to other polyolefins. But, due to the formation of wear debris, implants loosen and fail after 12–15 years of implantation. In order to enhance lifespan, the role of alumina (Al2O3) reinforcement on …
Published in Journal of Nanoscience, NanoEngineering & Applications · Vol. 4, Issue 3, 2014 · pp. 1–12 Read article
-
Interfacial Engineering of Carbon Fiber/Epoxy Laminates Using Functionalized Graphene Nanoplatelets: Experimental and Numerical Study
Abstract: Current research work studies the influence of amines(–NH₂) and carboxyl(–COOH) functionalized graphene nanoplatelets on the mechanical and thermomechanical behavior of unidirectional hybrid composite. Composites having different graphene concentration from 0 to 0.7 wt% were fabricated, characterized and analyzed for multiple testing - tensile testing, dynamic mechanical analysis (DMA) and Fourier transform infrared spectroscopy (FTIR). Tensile testing indicates better elastic modulus and tensile strength due to efficient load transfer between nanoparticles …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 61–77 Read article
-
Nano-mechanical and viscoelastic behavior of advance ultrafine graphite reinforced unsaturated polyester based prosthesis layup resin
Abstract: A new durable biomedical composite for prosthesis was designed to obtain enhance mechanical and viscoelastic properties, in particular nanohardness and young’s modulus. The nanoindentation technique was employed to investigate nano-scale mechanical properties of unsaturated polyester resin and its advance prosthesis lay-up nanocomposite resin with different amount of exfoliated graphite fillers loading. It has been observed that the young’s modulus of the nanocomposites gradually increase with increasing amount of reinforcement content. …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 7, Issue 2, 2020 · pp. 7–15 Read article
-
Advanced Functional Nanocomposites: Graphene Oxide Integration into Polyvinyl Alcohol Matrix
Abstract: This research explores how incorporating graphene oxide (GO) into polyvinyl alcohol (PVA) can improve its mechanical and thermal characteristics, with the goal of creating multifunctional nanocomposites suitable for advanced technological applications. GO was introduced into the PVA matrix at 0.5, 1, and 2 wt% via a scalable solution casting method. The resulting nanocomposites were characterized mechanically, thermally, and spectroscopically. Tensile testing revealed a significant improvement in mechanical performance, with tensile …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 50–59 Read article
-
Experimental Investigation on Tensile Characteristics of Hybrid Nanocomposite Joints by FSW with Optimized Welding Parameters
Abstract: Aluminium based nanometal matrix composites have emerged as highly promising class of materials in the field of materials domain, gaining importance mainly due to their low cost, isotopic properties and easy secondary processing. Cast aluminium matrix particle-reinforced composites have higher specific strength, specific modulus and good wear resistance when compared to unreinforced alloys. Continuous metal matrix phase facilitates controlled distribution of one or more nano-reinforcement materials. There are several conventional …
Published in Journal of Nanoscience, NanoEngineering & Applications · Vol. 9, Issue 2, 2019 · pp. 71–82 Read article
-
Mechanical performance of polymer composites reinforced with natural fibers for reliable structural biomaterial
Abstract: AbstractHybrid nanocomposite that exploits the synergy between natural fibers (industrial jute) in nano-reinforced unsaturated polyester (UP) based polymer can lead to improved properties while maintaining environmental appeal. Reinforcement of the UP-based resin with natural fibers (industrial jute) permits to retain flexural strength and hardness without sacrificing modulus, while also improving tribological properties. The industrial jute reinforced UP matrix composites having different filler was fabricated by compression molding technique and the …
Published in Journal of Modern Chemistry & Chemical Technology · Vol. 9, Issue 3, 2018 · pp. 13–22 Read article
-
Next-Generation Biodegradable Polymer Composites: Enhancing Mechanical and Thermal Performance through Green Reinforcements
Abstract: Next-generation biodegradable polymer composites, combining compostable matrices such as polylactic acid (PLA), polyhydroxyalkanoates (PHAs) and starch-based polymers with green reinforcements (e.g., nanocellulose, lignin, agricultural residues and other bio-fillers), offer a pragmatic route to reconcile high performance with end-of-life sustainability. This paper examines recent advances in the design, processing and interfacial engineering of such composites to enhance mechanical stiffness, strength, toughness and thermal stability while preserving—or intentionally controlling—biodegradation pathways. Emphasis is …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1780–1794 Read article
-
Fabrication and Characterization of Hybrid Composites Using Natural Fibers Reinforced in HDPE and Optimization of Injection Moulding Process Parameters to Minimize Shrinkage
Abstract: Materials are crucial for advancing human living standards. Over the past 20 years, composite materials have garnered significant attention owing to their unique properties and applications across various sectors. This study outlines the creation and analysis of a novel series of natural fiber-based composites, which incorporate jute, sisal, and hemp as reinforcements, with high-density polyethylene (HDPE) serving as the matrix, and produced through injection moulding. This study examines the effects …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 556–585 Read article
-
Selection of Best Natural Fibre for Retrofitting of Structure by Using AHP
Abstract: Ordinary concrete has certain characteristics such as; it is relatively strong in compression but weak in tension and tends to be brittle. To neutralize this weakness of concrete some natural reinforcement is provided to concrete and subsequent concrete is called fibre reinforced concrete. There are many types of natural fibres which are used in concrete as a reinforced material to increase the properties of concrete such as; Sisal, Coir, Hemp, …
Published in Journal of Structural Engineering and Management · Vol. 2, Issue 2, 2015 · pp. 13–19 Read article