Search
26 articles for “defect density”
-
Effect of Thickness of Absorber Layer on the Enhancement of Efficiency, and Performance of CH3NH3SnI3 based Perovskite Solar Cell using SCAPS-1D
Abstract: The present research article deals with the improvement of efficiency, and performance of tin based perovskite solar cells (PSCs) using SCAPS-1D software. SCAPS-1D has been used for investigating the absorber layer of the inverted p-i-n arrangement of tin based perovskite solar cells. The inverted p-i-n solar cell arrangement are Glass/ITO/NiO/CH3NH3SnI3/ PCBM/AL where ITO, NiO, CH3NH3SnI3, PCBM and Al are transparent conducting oxide, hole transporting layer (HTL), absorber layer and electron …
Published in Journal of Nanoscience, NanoEngineering & Applications · Vol. 11, Issue 4, 2021 · pp. 1–7 Read article
-
Quality Assurance Practices in Open-Source Versus Closed-Source Software Development: A Comparative Analysis
Abstract: Quality assurance (QA) is a decisive factor in determining whether software, whether openly developed or commercially closed, meets the reliability, maintainability, and usability expectations of its users. Open-source software (OSS) and closed-source software (CSS) pursue quality through structurally different mechanisms: OSS relies on distributed peer review, community-driven testing, and transparent issue tracking, while CSS depends on centralized quality departments, contractual accountability, and controlled release cycles. This article presents a comparative …
Published in Journal of Open Source Developments · Vol. 13, Issue 2, 2026 · pp. 34–44 Read article
-
Crystal Defects and Their Characterization in Modern Materials Science
Abstract: The physical and chemical properties of crystalline solids are fundamentally dictated by deviations from structural perfection, known as crystal defects. From the point-scale vacancies that drive diffusion to the planar boundaries that determine mechanical strength, defects serve as the primary "tuning knobs" in material design. This review provides a comprehensive examination of point, line, and planar defects, exploring their formation energetics and their role in plastic deformation via crystallographic slip. …
Published in International Journal of Crystalline Materials · Vol. 3, Issue 1, 2026 · pp. 15–19 Read article
-
Performance Optimization of Thin Film Cu(In,Ga)Se2 Solar Cell using BSF Layer
Abstract: This research work offers numerical analysis of CIGS solar cell designing an ultrathin absorber layer. The CIGS structure is outperformed from the theoretical and experimental evaluation considering the physical properties, dimensions and thickness of various layers of solar cell. Concentration of gallium within CIGS (Cu (In, Gа) Sе2) has major influence on the efficiency attributed to CIGS based solar cell and maximum power conversion efficiency of 27.26% is attained by …
Published in Journal of Nanoscience, NanoEngineering & Applications · Vol. 11, Issue 2, 2021 · pp. 19–26 Read article
-
Structural, Optical, Surface, and Gas-Sensing Properties of rGO/Sn1–xZnxO₂ Nanocomposites
Abstract: rGO/Sn₁–ₓZnₓO₂ nanocomposites with x = 0.00–0.75 were synthesized by sol–gel auto-combustion followed by wet impregnation with reduced graphene oxide. The adopted synthesis route enabled homogeneous Zn incorporation into the SnO₂ matrix and uniform distribution of rGO, leading to improved structural integrity and interfacial contact between the two components. XRD confirmed a dominant tetragonal cassiterite SnO₂ structure, while FTIR, FESEM, EDS, UV–visible, and BET analyses verified oxide–rGO coupling, Zn-dependent structural modification, …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 · pp. 429–452 Read article
-
An Empirical Analysis of Cost, Time, and Quality Relationships Using Correlation and Regression Techniques
Abstract: Cost, time, and quality have been recognized as the three key dimensions that determine construction project performance and are commonly represented through the "Project Management Triangle." However, despite their theoretical linkage, there is limited empirical evidence to quantify the nature of their relationships, particularly within developing construction markets. This paper seeks to contribute to addressing this shortfall by investigating the specific influence of cost and schedule variations upon quality outcomes …
Published in Journal of Construction Engineering, Technology & Management · Vol. 16, Issue 1, 2026 · pp. 52–60 Read article
-
Impact of Semiconductor Material Properties on Device Behavior and Circuit Performance: A Comprehensive Review
Abstract: Semiconductor materials play a fundamental role in determining the performance, efficiency, and reliability of modern electronic devices and circuits. This review presents a comprehensive analysis of how intrinsic and engineered material properties influence device behavior and overall circuit functionality. Key parameters such as bandgap energy, carrier mobility, thermal conductivity, and defect density are examined to understand their direct impact on switching speed, power consumption, and operational stability. The paper explores …
Published in Journal of Semiconductor Devices and Circuits · Vol. 13, Issue 1, 2026 · pp. 19–26 Read article
-
Electrochemical Exfoliation of Graphene Oxide (GO) and Thermally Reduced Graphene Oxide (TrGO) Using Ecofriendly Reducing Agent as Cow Urine
Abstract: The Graphene oxide (GO), the reduced form of GO i.e. (rGO) with thermally reduced graphene oxide (TrGO), have concerned significant interest in various fields with their exceptional properties. We investigate the electrochemical exfoliation processes of GO and rGO to understand their structural and electrochemical behavior of GO and TrGO through various characterization techniques. The electrochemical exfoliation method offers a versatile and scalable approach for the mass fabrication of the materials …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 89–100 Read article
-
Numerical Simulation and Parameter Analysis for Pentacene based Organic thin Film Transistor with HfO2 Gate Dielectric
Abstract: This paper explains 2D numerical simulation and Characterization of Electrical parameter of Pentacene (Organic semiconductor) based Organic thin film transistor (OTFT) devices with HfO2 as a gate dielectric and Electrical parameters including; Threshold Voltage (Vt), Mobility (µ),Ion/Ioff, and Transconductance (gm), Sub threshold slope (SS) are extracted. The numerical simulation includes model for defect density of state and field dependent mobility model.
Published in Journal of Semiconductor Devices and Circuits · Vol. 6, Issue 2, 2019 · pp. 28–34 Read article
-
Overview of Ionic Polarization: A Model Based Novel Approach
Abstract: This study presents a comprehensive analysis of ionic polarization through a novel model-based approach that integrates theoretical, computational, and experimental methodologies. Ionic polarization, which significantly influences the dielectric properties of materials, is examined through the lens of the Clausius-Mossotti equation and the Debye relaxation model, providing a theoretical framework for understanding the relationship between ionic displacement and dielectric behavior. To explore ionic displacement and polarization at the atomic level, advanced …
Published in International Journal of Cheminformatics · Vol. 2, Issue 2, 2024 · pp. 18–25 Read article
-
Mn Doping–Induced Enhancement of Ethanol Gas Sensitivity in CuO/Cu₂O/Cu Composites
Abstract: A composite of CuO/Cu2O/Cu was synthesized by heating cupric acetate up to 600 °C for 2 hours in air. The properties of pure CuO films and CuO/Cu2O/Cu films were compared. Films were fabricated by the doctor blade method. Polyethylene glycol was used as a binder to prepare films. Mn was doped to composite to enhance the gas sensing properties. Compositions of Mn doped samples were confirmed using XRFS. According to …
Published in Journal of Materials & Metallurgical Engineering · Vol. 16, Issue 1, 2026 · pp. 52–61 Read article
-
Representation-Theoretic Symmetry Reduction and Fuzzy-Grey Optimization of Modular Vibration Systems
Abstract: This paper presents a representation-theoretic framework for symmetry-aware vibration control in modular structural systems. Exploiting cyclic symmetry, the mass, damping, and stiffness operators are block-diagonalised into irreducible representations, reducing the full structural dynamics to a collection of lower-dimensional modal subsystems. This decomposition provides both computational efficiency and a rigorous mathematical description of symmetry-preserving dynamic behaviour. To account for imperfections arising in practical implementations, near-symmetry defects in stiffness and damping are …
Published in Emerging Trends in Symmetry · Vol. 2, Issue 1, 2026 · pp. 22–30 Read article
-
Classification of Fruits Based on Quality Using Artificial Intelligence
Abstract: The visual inspection method for fruit grading is prone to judgment distortion among different individuals. There is a demand for an automated fruit classification machine to replace labor-intensive processes with an intelligent system for fruit quality classification. This study proposes a practical real-time fruit quality classification system that classifies the fruit’s appearance in order to decrease human effort costs in the fruit industry. For the sorting and classification of fruits, …
Published in International Journal of Computer Science Languages · Vol. 1, Issue 2, 2023 · pp. 23–30 Read article
-
Effectiveness of PTFE-Based Nano-coatings in Improving Corrosion and Wear Resistance of Stainless Steel
Abstract: Polytetrafluoroethylene (PTFE) has emerged as a highly effective material for enhancing the durability and performance of metal surfaces, particularly in environments requiring superior corrosion resistance and low friction. This study investigates the application of PTFE coatings on various metallic substrates, with a focus on stainless steel and carbon steel, to improve their corrosion resistance, wear protection, and tribological performance. Utilizing advanced deposition techniques such as sol-gel and plasma spray, PTFE …
Published in International Journal of Photochemistry and Photochemical Research · Vol. 2, Issue 2, 2024 · pp. 32–38 Read article
-
Multi-Layer Aluminum–Polymer Hybrid Structures for Improved Automotive Impact Performance
Abstract: Layered metal–polymer hybrid laminates have emerged as promising candidates for lightweight automotive structures requiring high impact resistance and structural reliability. In this study, aluminum/glass–epoxy hybrid laminates were fabricated using a symmetric stacking sequence through hot compression molding to evaluate their mechanical and energy absorption performance. Density analysis revealed an average measured density of 2.34 g/cm³, closely matching the theoretical value of 2.36 g/cm³, with a deviation of approximately 1.02%, indicating …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 42–53 Read article
-
Advances and Challenges in the Development of High-performance Silicon Carbide (SiC) Power Devices
Abstract: Due to its distinct features, silicon carbide (SiC), a wide-bandgap semiconductor material, has attracted a lot of attention lately. SiC has superior electrical characteristics compared to silicon, making it an attractive material for high-performance power electronic devices. SiC-based devices can operate at higher temperatures, higher voltages, and higher switching frequencies, which can result in increased power density and efficiency. Recent advances in SiC device technology have led to the development …
Published in Journal of Semiconductor Devices and Circuits · Vol. 9, Issue 3, 2022 · pp. 15–20 Read article
-
Fabrication and Characterization of Hybrid Composites Using Natural Fibers Reinforced in HDPE and Optimization of Injection Moulding Process Parameters to Minimize Shrinkage
Abstract: Materials are crucial for advancing human living standards. Over the past 20 years, composite materials have garnered significant attention owing to their unique properties and applications across various sectors. This study outlines the creation and analysis of a novel series of natural fiber-based composites, which incorporate jute, sisal, and hemp as reinforcements, with high-density polyethylene (HDPE) serving as the matrix, and produced through injection moulding. This study examines the effects …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 556–585 Read article
-
Effects of Halloysite Nano particle Reinforcement of Epoxy Composite Using a Diglycidyl ether of bisphenol-A Prepared by Ultrasonication Casting
Abstract: This study explores a simple and operative approach for developing stronger epoxy-based composite materials by incorporating halloysite nanotubes (HNTs). The composites were made-up through hydraulic compression casting, combining ultrasonic mixing with applied pressure to produce consolidated composite sheets. HNTs were added to the epoxy resin at concentrations ranging from 1 to 5 wt.% at approximately 60°C, and the subsequent composites were examined to understand their internal structure, nanotube dispersion, and …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 Read article
-
Mechanical Performance Analysis of PET based Fibre Reinforced Concrete: A Review
Abstract: AbstractConcrete is characterized by various kinds of defects which include low tensile strength, low ductility, heavy weight and low energy absorption among others. Use of plastic wastes in concrete will result in safe, eco-friendly disposal as well as enhancement of certain physical and mechanical properties of concrete. Due to its certain user friendly and desirable properties such as low density, high tensile and impact strength, fabrication capabilities, long life, light …
Published in Recent Trends in Civil Engineering & Technology · Vol. 8, Issue 1, 2018 · pp. 41–46 Read article
-
Efficient Fault Detection in Power Transmission: A Review of Three-Phase Line Fault Detection with Hybrid Energy using MATLAB
Abstract: In urban regions, the density of power demand has significantly increased recently. Large-scale subterranean power cable installations are beginning to take the place of overhead transmission lines everywhere in the world because of environmental concerns in highly populated areas. The present project's primary objective is to use MATLAB to create a simulation model that includes 3ph symmetrical and unsymmetrical defects. Some have proven to be effective in detecting errors while …
Published in International Journal of Electrical Power and Machine Systems · Vol. 1, Issue 1, 2023 · pp. 42–47 Read article