Search
127 articles for “furnace”
-
Experimental Investigation on the Strength of Concrete with Partial Replacement of Cement using GGBS and Alccofine
Abstract: Cement is the most important ingredient of concrete. A large scale production of cement consumes large amount of energy and produce a large amount of carbon dioxide (CO2) gas which harmful to human as well as environmental and natural resources. So, to avoid the effect to use industrial waste productions as a supplementary cementitious material (SCM) in making concrete i.e. silica fumes, rice husk ash, fly ash, metakaolin, alccofine, ground …
Published in Journal of Construction Engineering, Technology & Management · Vol. 13, Issue 1, 2023 · pp. 35–43 Read article
-
Enhancing Blended Concrete Characteristics: A Comprehensive Review of GGBS and Steel Slag Effects from Performance and Sustainable Perspectives
Abstract: Avinash Kumar1, *, Sanjeev Kumar Verma2 Abstract Blended concrete, incorporating supplementary cementitious materials (SCMs), has gained significant attention in the construction industry due to its potential to improve concrete properties and promote sustainability. This review article provides an extensive examination of how two commonly utilized Supplementary Cementitious Materials (SCMs), namely Ground Granulated Blast Furnace Slag (GGBS) and Steel Slag, impact the properties of blended concrete. The review aims to provide …
Published in Journal of Construction Engineering, Technology & Management · Vol. 13, Issue 2, 2023 · pp. 26–32 Read article
-
Mechanical Properties of Geopolymer Concrete Paver Block
Abstract: Geopolymer concrete (GPC) is an innovative material and a real alternative to conventional Portland cement concrete. It relies on minimally processed natural materials or industrial by-products to significantly reduce its carbon footprint. However, the development of this material is still in its infancy, and a number of advancements are still needed. This paper focuses on the production of geopolymer concrete paver block (GPCPB) without using sodium hydroxide and investigates the …
Published in Journal of Geotechnical Engineering · Vol. 3, Issue 1, 2016 · pp. 51–55 Read article
-
Shear Strength Behavior of Different Soils
Abstract: The magnitude of shear strength of soils plays a major role in determining bearing capacity of shallow footings, frictional resistance for piles, stability of slopes, etc. for the safe and economic design of civil engineering structures. Based on the ideas of different researchers, shear strength of clay can be improved either by mixing sand or gravel, silty sand with gravel, and sand either with silt or gravel or granulated blast …
Published in Journal of Geotechnical Engineering · Vol. 9, Issue 1, 2022 · pp. 1–5 Read article
-
Assessment of Heat Stress and Noise Intensity Level in Workplace Area of the Iron Foundry
Abstract: The aims of this study were to measure the workplace heat stress and noise intensity levels in different sections of the foundries. The study was carried out in a small industrial city of southern peninsular of India, known for cluster of foundry establishments. The heat and noise level were measured in melting, fettling, gas cutting, heat treatment furnace, and administrative sections measuring the dry bulb temperature(TDB °C), wet bulb temperature …
Published in Journal of Industrial Safety Engineering · Vol. 1, Issue 2, 2014 · pp. 13–17 Read article
-
Assessment of Hot Environment in Foundry Industry using Modified Heat Stress Index
Abstract: Indian foundry industry being one of the highest contributors where workers are exposed to varied health hazards attributed to fumes, dusts, gases, heat, noise, vibration and radiation. In step with the connection between atmosphere temperature and human thermal balance, living environments higher than 35°C or operating environments higher than 32°C were considered as hot environments. In hot-dry work place, workers exposed to extreme heat can experience occupation illness and injuries …
Published in Journal of Industrial Safety Engineering · Vol. 2, Issue 2, 2015 · pp. 1–5 Read article
-
Management of Waste Generated in Steel Rerolling Industries of Nepal
Abstract: The study on nature and management of waste generated in iron & steel industries of Nepal provides an overview of the nature and type of waste generated and their current management practices. The purpose of the study was to identify the nature of waste generated in iron and steel industries of Nepal and recommend appropriate measures for its management. For this study, five iron & steel industries were visited to …
Published in Journal of Industrial Safety Engineering · Vol. 7, Issue 3, 2020 · pp. 1–7 Read article
-
Evaluation of Heat Stress Exposure to Occupational Workers at Workplace
Abstract: Heat stress is considered as an occupational health hazard encountered in indoor as well as outdoor environments. In industries, many operations are carried out which involve either heat generating sources like boiler, furnace, dryers etc. or hot operations like welding, melting, glass blowing and pouring. Moreover, the extremes of temperature in summer also add to the level of exposure to heat stress. Exposure of occupational workers to heat stress can …
Published in Journal of Industrial Safety Engineering · Vol. 9, Issue 1, 2022 · pp. 9–15 Read article
-
Effect of Magnetic Field on Casting Parameters
Abstract: AbstractThe casting process is one of the oldest manufacturing methods involving squeezing / jolting the green sand used as moulding material, and further was developed with use of binders such as clay/organic resins. The constants search for newer moulding material lead to the magnetic mould involving steel shots and application of magnetic field. The preliminary trials on one of the process parameters i. e. Magnetic field was carried out and …
Published in Journal of Materials & Metallurgical Engineering · Vol. 8, Issue 3, 2018 · pp. 30–35 Read article
-
Wear Behavior of Al-Alloy (Al-5 Mg) in-situ Reinforced TiB2 Particulate
Abstract: A research has been carried out for replacing Al monolithic alloys by aluminium (Al) based metal matrix composites (MMCs) in many engineering applications where high wear resistance and stiffness are required. In this paper, the investigated dry sliding wear behavior of TiB2 particulate reinforced composite of Al-Alloy (Al-5 Mg) is discussed. The in-situ Al-Alloy (Al-5 Mg) 10wt% TiB2 composite material were prepared by molten flux reaction synthesis using electric melting …
Published in Journal of Materials & Metallurgical Engineering · Vol. 4, Issue 3, 2014 · pp. 32–37 Read article
-
Adoption of Heat Recovery Technology in Sintering Process to Reduce Carbon Imprint
Abstract: India is the second largest steel producer in the world after China. The 2017 National Steel Policy of India set out the ambitious plan of 250 MT steel production and per capita consumption to around 160 kg by 2030. The dominant iron-making route is blast furnace (BF), which is an energy-intensive process based on fossil fuel consumption. The steel industry contributes around 7% of all greenhouse gas (GHG) emissions. India …
Published in Journal of Materials & Metallurgical Engineering · Vol. 12, Issue 3, 2022 · pp. 38–44 Read article
-
Analysis of Oxidation Behavior on T-22 Boiler steel at 800°C
Abstract: The behavior of boiler steel T-22 in a rich air environment has been studied under the condition of isothermal at 800°C for 50 cycles in a cyclic manner. The kinetics of oxidation was established for boiler steel T-22under cyclic conditions for 50 cycles by weight change technique per unit area. Each cycle heating the sample at 1 hour followed by cooling 20 minutes at ambient temperature. Detonation gun spray techniques …
Published in Journal of Polymer & Composites · Vol. 8, Issue 1, 2020 · pp. 18–25 Read article
-
Development of Refractory Synthesized from Waste Ceramic Fiber and Chamotte
Abstract: Research on refractory materials is always essential in thermal engineering to ensure both heat savings and environmental protection. Raw materials used initially have a great influence on the production process and product properties. In addition, the refractory products are tested under conditions of high temperature and varying intensity, such as tests of thermal shock resistance. In this study, new refractory composites were prepared by mixing waste ceramic fibers with chamotte …
Published in Journal of Polymer & Composites · Vol. 8, Issue 2, 2020 · pp. 101–109 Read article
-
Novel Porous Refractory Synthesized from Diatomaceous Earth and Rice Husk Ash
Abstract: Refractory materials are products used in thermal equipment to protect the fire and prevent heat loss to the outside environment. Thermal equipment such as driers, ceramic kilns, glass or metal furnaces and others always consume high heat in the combustion of the fuel. If the thermal equipments have high heat loss which cause wastes of fuel and increases production costs. Therefore, researchers are always looking for a solution to minimize …
Published in Journal of Polymer & Composites · Vol. 8, Issue 2, 2020 · pp. 128–137 Read article
-
Engineering Properties of Alkali Activated Materials Produced from Thu Duc Water Plant Waste Sludge, Fly Ash, and Alkaline Activator by Semi-dry Pressing Method
Abstract: Alkali activated material is a product manufactured to serve the needs of construction. Theproduction of alkali activated material has many advantages compared to other traditional bakedmaterials. The product is not heated at high temperature, so it saves energy and reduces the amountof waste impacting negatively to ecology system and human life. The raw materials for production ofalkali activated materials are re-used from other industrial solid wastes such as fly ash, …
Published in Journal of Polymer & Composites · Vol. 9, Issue 1, 2021 · pp. 39–48 Read article
-
Microstructural Investigation on Strength of New Age Mortar Synthesis with Thermosetting Polymer, GGBS, Fly Ash and Quarry Dust
Abstract: AbstractThermo setting polymer mortars containing Resin, hardener, fly ash, Quarry dust and GGBS (Ground Granulated Blast furnace slag). Merging representation of bio phenol-A-Di-glycidyl ether-based polymer with fly ash, Quarry dust and GGBS results are presented here for this present study. An innovative process is used to prepare the specimen in mild condition with commercial thermo setting polymer-based resin and hardener, fly ash, GGBS, along with quarry-dust-based paste. Following this procedure, …
Published in Journal of Polymer & Composites · Vol. 11, Issue 1, 2023 · pp. 63–71 Read article
-
Production of Alum from Aluminium Drink Cans Waste for Water Treatment
Abstract: The graphite furnaces atomic absorption spectrophotometry (GFAAS) technique has been previously used to quantify the aluminium (Al) content in soft drinks made from aluminium cans over the course of a 12-month storage period. The current research aimed to determine the efficacy of alum obtained from waste soft drink cans compared to the alum obtained from local markets in treating water from Shatt al-Arab, Basrah, Khorramshahr, and Abadan, Iraq. The Shatt …
Published in Journal of Polymer & Composites · Vol. 11, Issue 2, 2023 · pp. 102–109 Read article
-
Experimental Investigation on Mechanical Properties of Concrete Replacing of Steel Slag as Coarse Aggregate
Abstract: The basic objective of this study was to identify alternative source of good quality aggregate which is depleting very fast due to the fast pace of construction activities. This paper describes the optimum level of replacement of Energy Optimized Furnace (EOF) steel slag by weight of coarse aggregate for a mix proportion of M20 grade concrete to find out the optimum ratio of steel slag. Civil Engineers have been challenged …
Published in Journal of Structural Engineering and Management · Vol. 4, Issue 2, 2017 · pp. 44–49 Read article
-
Mechanical Behaviour of Conventional Concrete Using Fly Ash and Steel Fibre
Abstract: Concrete that area unit victimization with the waste materials, recycled materials etc. could be a revolutionary topic at this time of concrete business. This kind of concrete that resembles the traditional concrete, however the assembly or utilization of such concrete needs minimum quantity of energy and causes least hurt to atmosphere. This kind of concrete absorbs the waste product that is additionally useful for atmosphere aspects [1]. Some SCMs area …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 4, Issue 1, 2017 · pp. 18–23 Read article
-
Performance of Ni3Al and TiO2 Coatings on T91 Boiler Tube Steel in Simulated Boiler Environment at 900°C
Abstract: Boiler steel tube corrosion in coal fired boiler is main subject during design and operation of thermal power plant and it leads to both direct and indirect loss of cost and energy, including losses due to plant shut down time and inefficiency of operation. One of the feasible solutions to solve out this problem is providing surface coating on boiler steel tube, which on one hand protects the tube from …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 3, Issue 2, 2016 · pp. 27–34 Read article