Search
1013 articles for “Materials Optimization”
-
Enhancing Mechanical and Durability Properties of Coconut Shell Concrete Using Fly Ash
Abstract: The increasing demand for sustainable and lightweight construction materials has driven research into alternative aggregates for concrete production. This study investigates the mechanical and durability properties of coconut shell (CS) concrete with varying percentages of fly ash replacement. The research evaluates compressive strength, split tensile strength, water absorption, and workability to determine the feasibility of CS concrete as a structural material. Experimental findings indicate that incorporating 10% fly ash (CSF10 …
Published in Recent Trends in Civil Engineering & Technology · Vol. 15, Issue 2, 2025 · pp. 19–24 Read article
-
Nanostructure-Induced Thermoelectric Enhancement in Bi₂Te₃ Nanorods Design, Analysis, and Performance Evaluation
Abstract: Thermoelectric materials capable of efficient energy conversion near room temperature are critical for waste heat recovery applications. In this work, solution-grown Bi₂Te₃ nanorods were synthesized via a trioctylphosphine-assisted thermal decomposition route, and the influence of surfactant-induced nanostructuring on their thermoelectric properties was systematically investigated. Structural analysis using X-ray diffraction and Rietveld refinement confirmed the formation of rhombohedral Bi₂Te₃ with the emergence of Bi₂Te₃–BiTe nanocomposites at higher surfactant concentrations. Electron microscopy …
Published in International Journal of Energy and Thermal Applications · Vol. 4, Issue 1, 2026 · pp. 34–44 Read article
-
Thermal Performance Analysis and Optimization of Pin-Fin Heat Sink Using CFD, Taguchi Method, and Machine Learning
Abstract: Efficient thermal management is essential for improving the performance and reliability of modern engineering systems and electronic devices. This study presents the design, simulation, and optimization of a pin-fin heat sink using SolidWorks for three-dimensional modeling and ANSYS for thermal and computational fluid dynamics (CFD) analysis. Four different pin-fin geometries, namely square, pentagon, octagon, and circular fins, are considered to evaluate their thermal performance under varying operating conditions. Aluminum is …
Published in Trends in Mechanical Engineering & Technology · Vol. 16, Issue 2, 2026 · pp. 8–20 Read article
-
Performance Evaluation of Modified Concrete Incorporating Fly Ash, Silica Fume, Rice Husk Ash, and Calcium Nitrate
Abstract: The growing demand for sustainable and high-performance concrete has led to the incorporation of supplementary cementitious materials (SCMs) and chemical admixtures to enhance mechanical and durability properties. This study investigates the effect of 15% fly ash, 10% silica fume, 10% rice husk ash, and 3% calcium nitrate as a partial replacement for cement in M25 and M30 grade concrete. Experimental results demonstrate that the modified concrete exhibited an increase in …
Published in Journal of Structural Engineering and Management · Vol. 12, Issue 2, 2025 · pp. 35–39 Read article
-
Study The Effect of Metakaolin Powder in Hot Mix Asphalt as Mineral Filler
Abstract: Mineral fillers are crucial for bridging the spaces between the internal particles of the asphalt matrix. The purpose of this study is to investigate the mechanical properties of hot mix asphalt as well as the impact of utilising Metakaolin (MK) as a mineral filler. Coarse aggregate, fine aggregate, and filler are the main components of hot mix asphalt (HM). With or without modifiers, materials and asphalt binders. HMA components have …
Published in Journal of Polymer & Composites · Vol. 11, Issue 10, 2023 · pp. 9–15 Read article
-
Production of Injection Moulded Natural Fiber Reinforced Hybrid Composites and Assessment of Hybridization’s Effect on Mechanical Properties
Abstract: Over the past two decades, rising environmental awareness, public concern over waste, and stricter government regulations have encouraged companies to reduce their reliance on petroleum-based fuels and products. Consequently, there is a clear need to find sustainable, eco-friendly substitutes for the materials currently in use. This shift has renewed attention on renewable resources and sparked wider interest in advanced composites and green materials research. With this in mind, the present …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 246–271 Read article
-
Green Concrete Using Fly Ash and Silica Fume
Abstract: Recycled coarse aggregate can also be used by partially replacing natural concrete aggregates, so that construction and demolition waste can be further used for aggregates in new construction. Recycled coarse aggregate includes brick, tile aggregates, crushed stone aggregates, glass aggregates, and demolished aggregates. In this paper, different recycled aggregates are used by 40 and 60% replacement with natural aggregates of size 20 mm. Granite stone, brickstone, concrete debris are used …
Published in Recent Trends in Civil Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 57–62 Read article
-
Machine Learning-Based Structure–Property Quantification of Advanced Polymer Composites
Abstract: Advanced polymer composites are widely used in high-performance engineering due to their superior mechanical and multifunctional properties. Accurate structure–property quantification is essential for efficient material design and reducing experimental costs. Existing Machine Learning (ML) approaches often exhibit limited predictive generalization due to inadequate feature discrimination and suboptimal hyperparameter tuning. To address these limitations, the proposed method enhances the ability to capture the complex nonlinear interactions among composite structural descriptors. The …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 Read article
-
Transforming the Healing Spaces: – Exploring the Impact of Interior Design on Art Therapy Rooms
Abstract: Art Therapy is one of the widely used therapeutic methodologies in psychology with the motive of dealing and eliminating a person’s anxious thoughts or emotions by teaching them how they can cope with their cognitive conditions. However, it is often noted that the clinical environment this procedure takes place in may hinder with the proper development of a patient’s mental health. Therefore, an art therapy clinic should be designed in …
Published in International Journal of Behavioral Sciences · Vol. 1, Issue 1, 2024 · pp. 01–08 Read article
-
Using of the sea grasses for the removal of some industrial organic dyes; bromo cresol purple from aqueous solutions
Abstract: Abstract: The objectives of this study are evaluating the efficiency of low cost adsorbents of activated carbon obtained from sea grasses. Using the sea grasses for the removal of some industrial organic dye; bromo cresol purple indicators from aqueous solutions and studying the impact of some of the factors including different dosages , pH, different concentrations, different temperature and effect of time of adsorbed materials. Adsorption efficiency of dye onto …
Published in Emerging Trends in Chemical Engineering · Vol. 6, Issue 3, 2019 · pp. 29–36 Read article
-
Improved Prediction of Fluid Contacts using Calibrated Material Balance Models
Abstract: The demand for oil has been on the high in the recent past and will continue as search for sustainable alternative energy sources intensifies. The exploration and exploitation of oil from subsurface reservoirs have posed several environmental challenges which include flaring and improper water disposal to name a few, caused by excessive production of gas and water. Hence, it is important to establish a reservoir performance monitoring scheme that will …
Published in Journal of Petroleum Engineering & Technology · Vol. 4, Issue 2, 2014 · pp. 25–36 Read article
-
Optimization of Stellite Defect in Manufacturing of Engine Valves: A Review
Abstract: Intake and exhaust valves are the important components of an engine valves which are used to control flow and replacement of fuel gases inside the cylinder. This work mainly deals with defect known as stellite defect in different sizes of engine valves; and methodology adopted to prevent valve from stellite defect. Valve base material is low alloy steel (AISI 4140) and upper surface of engine valve is generally hard faced …
Published in Journal of Automobile Engineering and Applications · Vol. 3, Issue 1, 2016 · pp. 1–4 Read article
-
Analysis of Proposed Diagrid Geometry Using Golden Ratio in Non-linear Regime of Material
Abstract: Lateral loads are critical in the design of high-rise structures. The buildings need to have high stiffness and must be able to resist lateral deformations and torsional rotations without having discomfort to the user. Diagrid structural system is one of the systems used in resisting lateral forces. In this study, diagrid geometry is generated using the ‘Golden Ratio’ concept and used to model 40, 50, and 60 story structures. Two …
Published in Journal of Construction Engineering, Technology & Management · Vol. 11, Issue 2, 2021 · pp. 1–11 Read article
-
A Constraint-Driven Generative Design Methodology for Modular Actuated Robotic Components in Decentralized Manufacturing
Abstract: This work formalizes a constraint-driven generative design framework for actuator-integrated robotic components intended for decentralized additive manufacturing. Conventional topology optimization typically prioritizes structural efficiency while treating actuator integration, modular interfaces, and fabrication constraints as secondary considerations. In contrast, the proposed methodology encodes these requirements as first-order geometric and mechanical constraints prior to automated material redistribution. The framework defines preserved actuator geometry, bounded design envelopes, representative loading abstractions, and manufacturability-aware domains …
Published in International Journal of Robotics and Automation in Mechanics · Vol. 4, Issue 1, 2026 · pp. 1–12 Read article
-
Development of Controlled Concrete by using Hypo Sludge
Abstract: Over 300 million tones of industrial wastes are being produced per annum by chemical and agricultural process in India. These materials pose problems of disposal and health hazards.The wastes like phosphogypsum, fluorogypsum and red mud contain obnoxious impurities which adversely affect the strength and other properties of building materials based on them. Out of several wastes being produced at present, the use of phosphogypsum, flurogypsum, lime sludge, hypo sludge, red …
Published in Journal of Structural Engineering and Management · Vol. 1, Issue 1, 2014 · pp. 16–21 Read article
-
Optimum Mixture Proportioning of Sawdust Ash Blended Sand-Stone Dust Blocks Using Scheffe’s Regression Theory
Abstract: This study carried out an experimental investigation on the compressive strength of sawdust ash blended sand-stone dust block of size 450 x 225 x 150 mm using Scheffe’s (5, 2) regression theory. The compressive strength of sawdust ash blended sand-stone dust blocks obtained based on fifteen trial mix ratios were used to develop the mathematical model while the results of the compressive strength values obtained based on the additional fifteen …
Published in Journal of Construction Engineering, Technology & Management · Vol. 13, Issue 2, 2023 · pp. 33–40 Read article
-
Chemical Reactor Design and Analysis: A Review
Abstract: Chemical reactors play a critical role in industries such as oil and gas, chemical processing, and power generation, where they operate under extreme pressure and handle highly toxic, compressible fluids. The growing need for alternative energy sources has led to an increased demand for vessels capable of withstanding high pressure and temperature, especially in the chemical and petroleum industries. Recent innovations in chemical reactor technology have concentrated on creating new …
Published in Recent Trends in Fluid Mechanics · Vol. 12, Issue 2, 2025 · pp. 49–59 Read article
-
Influence of Cementitious and Aggregate Replacements on the Compressive Strength of Pervious Concrete
Abstract: Pervious concrete is a sustainable construction material designed to enhance stormwater management while maintaining adequate mechanical strength. This study investigates the compressive strength of pervious concrete cubes with various cementitious and coarse aggregate replacements. The research examines the effects of fly ash, silica fume, steel slag, and rubber chips on compressive strength at 7 and 28 days of curing. The results indicate that moderate fly ash replacement enhances compressive strength, …
Published in Journal of Construction Engineering, Technology & Management · Vol. 15, Issue 2, 2025 · pp. 9–14 Read article
-
Optimization of Polymer-Enhanced Sustainable Concrete: A Composite Approach with Bentonite and Crumb Rubber Aggregates
Abstract: The disposal of rubber tyres has become challenging; on the other hand, the utilization of rubber tyres is also increasing daily in society. The successful use of crumb rubber as an alternative aggregate and bentonite as a partial cement replacement in concrete composites has been well established through prior research. These materials have individually demonstrated their potential to enhance sustainability, improve concrete properties, and reduce environmental impact, paving the way …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 701–715 Read article
-
Development of Environmentally Friendly Concrete by Incorporating Rubber and Leather Waste
Abstract: The valorization of post-consumer polymeric waste into high-performance composite materials offers a sustainable strategy for advancing circular economy principles and reducing environmental impacts.This study investigates the feasibility of utilizing recycled crumb rubber from end-of-life tires and leather-derived polymeric waste from the footwear industry as sustainable fillers in polymer-modified cementitious composites. Crumb rubber and processed leather waste were incorporated as partial replacements for natural fine aggregate at replacement levels of 0%, …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 · pp. 547–563 Read article