Search
711 articles for “Bats”
-
Synthesis and Characterization of Green Synthesized Iron Nano Particle (GInP) Using Eucalyptus globulus for Lead Removal
Abstract: The application of green synthesized iron nanoparticle for the removal of lead is researched in this study. The FT-IR and XRD results reveal that a nanoparticle with 80 nm size could be synthesized using Eucalyptus globulus leaf extract. The specific surface area of the nanoparticle was found to be 59 m2/g. The lead removal capability of the green synthesized iron nanoparticle (GInP) was investigated for lead concentration ranging from 50–250 …
Published in Journal of Materials & Metallurgical Engineering · Vol. 10, Issue 3, 2020 · pp. 20–25 Read article
-
Sizing and Power Estimation Models of an Off-grid Wind Power Supply System in Sokoto, Nigeria
Abstract: AbstractThe exploitation of wind energy for electricity generation could be done by the use of wind turbines. The power output from the wind generator fluctuates due to the variability of wind speed and therefore storage facilities are needed for power supply stability. This research focuses on the wind power potential investigations, sizing of wind power system components and determination of the better wind turbines for residential power supply in Sokoto, …
Published in Journal of Nuclear Engineering & Technology · Vol. 10, Issue 1, 2020 · pp. 1–7 Read article
-
Innovative Design and Fabrication Techniques for an Octawalker: A Comprehensive Study
Abstract: The octawalker is a walking aid that is remote-controlled.We intend to increasesecurity to a new level. In order to benefit our country, we created this initiative using our thoughts. composed of two motors that run on 12 volts DC.DC battery power supply that can be recharged. These checkpoints demand all vehicle traffic to stop. According to Webster, a robot is & an autonomous device that performs functions normally ascribed to …
Published in Journal of Nuclear Engineering & Technology · Vol. 13, Issue 3, 2023 · pp. 30–35 Read article
-
PVC Pipe Designer Furniture
Abstract: AbstractPolyvinyl chloride (PVC) products are 100% recyclable physically, chemically and energetically. This can be used to make various products like steam houses, kid’s houses, shoes stands, laptop stands, kid’s scooters, bookshelves etc. There are many benefits of PVC such as, high impact resistance, good temperature capability, light weight etc. PVC’s versatility, cost effectiveness and an excellent record of use, makes it capable enough that it can replace traditional building materials …
Published in Journal of Polymer & Composites · Vol. 4, Issue 2, 2016 · pp. 29–33 Read article
-
Evaluation of Compatibility of Elastomeric Component of Master Cylinder with Brake Fluid
Abstract: Importance of proper functioning of braking system of any automobile is imperative for ensuring safe operation. Master cylinder is a heart of the brake system and rubber seals and cups are its vital parts. Specially processed and designed seals resist leakages and transformation due to temperature changes or reaction with the brake fluid. This paper presents the compatibility study conducted on two different rubber materials, NBR and SBR-EPDM (identified by …
Published in Journal of Polymer & Composites · Vol. 8, Issue 3, 2020 · pp. 34–42 Read article
-
An Optimize Formulation to Synthesis of size Controlled Hydrophobic Starch Acetate Nanoparticles using Box-Behnken Design
Abstract: The best way to improve the overall performance of native starch is by chemical modification. In recent years, hydrophobically modified starch has attracted considerable attention for the design and manufacture of novel nanoparticulate drug delivery carriers. The purpose of this research was to synthesize hydrophobic starch nanoparticles (NPs) and to optimize process factors through the use of response surface methodology (RSM). The corn starch acetate (CSA) NPs was synthesized using …
Published in Journal of Polymer & Composites · Vol. 10, Issue 1, 2022 · pp. 32–54 Read article
-
Nanomaterials and Their Effects on the Environment: Analyzing Widespread Use
Abstract: Due to the need and uses of nanoparticles in a wide variety of fields of human activity, including industry, agriculture, commerce, medical, and public health, there has been a significant uptick in interest in nanotechnology among the general populace. Because of the inevitability of environmental exposure to nanomaterials as a consequence of their increasing incorporation into our everyday lives, more and more focus is being placed on the study of …
Published in Journal of Polymer & Composites · Vol. 11, Issue 1, 2023 · pp. 97–103 Read article
-
Investigation of Mechanical Characteristics of 3D Printed Composite Materials (Thermoplastic Urethane and Nylon (PA6))
Abstract: 3D printing has emerged as a game-changer, progressively replacing conventional metals and thermosetting polymers, primarily due to its capacity to create lightweight structures with impressive mechanical attributes. The technology's advantages, such as minimized material wastage, design adaptability, and the ability to craft intricate structures, have propelled its widespread adoption. Within the realm of additive manufacturing, Fused Deposition Modeling (FDM) stands out as a technique capable of producing intricate functional components. …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 65–76 Read article
-
Comparison of Symmetrical and Asymmetrical Cascaded H-Bridge Inverter with Single DC Source
Abstract: This paper presents the comparison of traditional cascaded H-bridge inverter with isolated DC sources (symmetrical arrangement) and the proposed cascaded H-bridge inverter with single DC source (asymmetrical arrangement). Also, fundamental switching strategy is used to generate the control pulses. A conventional cascaded H-bridge (CHB) inverter requires ‘n’ numbers of DC sources for 2n + 1 levels. Without requiring transformers, the scheme proposed here allows the use of a single DC …
Published in Journal of Power Electronics and Power Systems · Vol. 2, Issue 1, 2012 · pp. 8–17 Read article
-
Design and Simulation of Z-Source Inverter Fed Brushless DC Motor Drive Supplied With Fuel Cell for Automotive Applications
Abstract: This paper presents design and simulation of Z-source inverter fed brushless DC motor drive supplied with fuel cell for automotive applications. The brushless DC (BLDC) motor are used due to many advantages such as high efficiency, high torque, high reliability, high-power density, lower maintenance compared to other motors in electric transport applications. The BLDC motor drive is with voltage source inverter (VSI) or current source inverter (CSI) because of low …
Published in Journal of Power Electronics and Power Systems · Vol. 6, Issue 3, 2016 · pp. 60–71 Read article
-
Software and Hardware Implementation of Quasi z Source Inverter in DC-DC Converter with DC Motor as Load
Abstract: DC/DC power converters are employed in applications like telecom, industrial, automotive, military, aerospace and motor drives. The dc/dc converter market is forecast to grow at a strong rate to $ 4.3 billion by 2016. The primary factor limiting the widespread application of low voltage producing renewable energy sources to motor load is interfacing of converter system. The traditional voltage source inverter (VSI) cannot be dealt without overrating of inverter because …
Published in Journal of Power Electronics and Power Systems · Vol. 5, Issue 3, 2015 · pp. 97–107 Read article
-
The Energization Transients of 6-Pulse Rectifier Circuits
Abstract: This paper addresses the energization transients of 6-pulse rectifier circuits. It applies anefficient representation of the diodes in order to describe their performance in both theforward and reverse directions. Without any loss of generality, the suggested method isapplied to the classical un-controlled six-valve full-wave rectifier bridge configuration. Theeffect of the load resistance, the eventual presence of smoothing shunt-capacitors and seriesinductors as well as the waveform of the supply voltage is …
Published in Journal of Power Electronics and Power Systems · Vol. 10, Issue 1, 2020 · pp. 18–30 Read article
-
Design and Analysis of a Solar-Wind Hybrid System
Abstract: Renewable energy sources like wind and solar energies can be combined to increase the totalpower generation and thereby increase the efficiency of the system. The combination alsoprovides a means to overcome the intermittent nature of the solar and wind renewable energysources, since one source can be used for power generation when the other is not available.AC-DC converters are used to convert the alternating voltage of the wind generator to aconstant …
Published in Journal of Power Electronics and Power Systems · Vol. 10, Issue 1, 2020 · pp. 1–8 Read article
-
Construction/Assembling of a Low Cost Adsorption Apparatus for Cored Clay Shales
Abstract: The secret to unlocking these reserves lies in accurate experimental data which in turn depends on the experimental method used. Recently many procedures such as manometric, volumetric and gravimetric have been developed to quantify adsorption. In this paper, we show how to construct/assemble a simple manometric adsorption apparatus for gas adsorption. The setup is inexpensive and can be built easily using part available in university laboratories. Furthermore, it can be …
Published in Journal of Petroleum Engineering & Technology · Vol. 6, Issue 3, 2016 · pp. 54–60 Read article
-
Solutions to Problems Faced in Well Log Analysis in fractured metamorphic Reservoir Systems Due To Multiple Porosities and Lithology’s
Abstract: Metamorphic rocks are the most bottomless non-terrigenous sedimentary rock and are made essentially out of transformative minerals. Most metamorphic rocks shape from calcareous stores that collect in marine conditions running from salt marshes to reefs to profound sea bowls. Unmistakable and one of a kind parts of transformative rocks are their dominatingly intrabasinal starting point, their essential reliance on natural exercises for their constituents and their powerlessness to change by …
Published in Journal of Petroleum Engineering & Technology · Vol. 9, Issue 1, 2019 · pp. 36–42 Read article
-
Working model on Power Generation in Offshore Rig Using Tidal Energy
Abstract: Abstract- Hydrocarbons are a significant source of energy. Its expanding usage has caused the hydrocarbon exploration to go past the shore. Offshore Rig power prerequisites are higher contrasted with onshore rigs. Diesel Generators are customarily utilized for the power prerequisites of offshore rigs. This project expects to propose a plan to utilize the renewable source of energy (fundamentally tidal energy) for energy age in offshore. The thought is to have …
Published in Journal of Petroleum Engineering & Technology · Vol. 10, Issue 1, 2020 · pp. 46–58 Read article
-
Study of Crude Oil Degradation Using Bio-stimulant: The Concept of Remediation Application
Abstract: The Total Petroleum Hydrocarbon (TPH) degradation was monitored in a batch reactor with the addition of bio-stimulants of palm oil processed waste water (POPWW) and NPK fertilizer in contaminated clay soil medium. The comparative study on the performance of both bio-simulants revealed that the NPK fertilizer was more effective than the palm oil processed waste water (POPWW). This study is based on the overview on the degradation of petroleum hydrocarbon …
Published in Journal of Petroleum Engineering & Technology · Vol. 13, Issue 2, 2023 · pp. 13–23 Read article
-
Vehicle Hybridization: Concept of future car engine by fuel – compressed air combination.
Abstract: Nowadays, Vehicle’s exhaust product is one of the sources of environmental problems in India. Their products of combustion are causing the greenhouse effect, depletion of Ozone layer, etc. On the other hand, a case study research on fossil fuel in the year 2004, predicts that if the oil is consumed at the current rates, 80% of the entire available resource will be consumed very soon. So now we need to …
Published in Journal of Production Research & Management · Vol. 8, Issue 3, 2018 · pp. 38–41 Read article
-
Design and Analysis of Automobile Hood
Abstract: Bonnet is a main component of front portion of a car one which is used for many purposes. It is usedto decorate the car and add luxurious look. Bonnet is made in aerodynamic shape to reduce airresistance. Bonnet generally used to cover car engine. Therefore, the bonnet system is an accesspanel to the engine compartment to enable maintenance of power train, drive belts, battery, fluidlevels and lamp units, and it …
Published in Journal of Production Research & Management · Vol. 11, Issue 1, 2021 · pp. 42–52 Read article
-
A General Study Work-Life Balance in Higher Education for Women in India
Abstract: Women's battle for faculty posts in athletic training Women in professor roles should have an equalwork-life balance. a work environment that values balance and gives women faculty members thefreedom to organize and prioritize their schedules is essential for achieving work-life harmony. It iscrucial for women to have support systems both inside and outside of the workplace if they are to beable to manage their responsibilities. More than 85% of working …
Published in Journal of Production Research & Management · Vol. 12, Issue 2, 2022 · pp. 1–7 Read article