Search
126 articles for “WT”
-
Solar-Responsive Photo-Thermal Polymer Composites with Carbon Nanostructures for On-Demand Water Purification
Abstract: The development of solar-responsive polymer nanocomposites offers a sustainable pathway for water purification. In this work, polyvinyl alcohol (PVA) films reinforced with graphene nanoplatelets (GNPs) and multi-walled carbon nanotubes (MWCNTs) were fabricated and systematically investigated for their mechanical, thermal, viscoelastic, and thermal transport properties. Neat PVA displayed moderate tensile strength (~38 MPa) and high elongation (~165%), whereas 1.0 wt% nanofiller loading enhanced tensile strength to ~52 MPa and modulus to …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 199–209 Read article
-
Optimization of Direct Ink Writing Process Parameters for Liquid Silicone Rubber/TiO2 Composite Ink
Abstract: The purpose of this research is to develop and optimize the Liquid Silicone Rubber (LSR)/Titanium Dioxide (TiO₂) composite inks in Direct Ink Writing (DIW)-based 3D printing systems. The primary research objective was to use enhancement of mechanical, rheological, and dielectric characteristics of LSR using TiO₂ reinforcement but still retain extrusion stability and dimensional consistency. TiO₂ content (0, 5, 10, and 15 wt%) and catalyst and glycerol ratios were regulated and …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 240–259 Read article
-
Hybrid Epoxy Composites with Areca and Abaca Fibers: Effect of Nano-SiO₂ on Mechanical Properties
Abstract: This study explores the fabrication and mechanical evaluation of sustainable epoxy-based hybrid composites reinforced with Areca fiber (ARF), Abaca fiber (ABF), and nano-silica (SiO₂). The composites were made using a hand layup process, maked five variants (S1–S5) with ARF content ranging from 0–40 wt% and nano-silica content from 0–8 wt%, while maintaining ABF as the primary reinforcement. Mechanical performance was assessed through tensile strength (TS), flexural strength (FS), and impact …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 606–613 Read article
-
Mechanical & Tribological Characterization of Al2024-Alumina-Graphite Reinforced Monolithic and Hybrid Composites
Abstract: This work investigates the mechanical characteristics of Al2024-Al2O3-Graphite reinforced monolithic and hybrid composites fabricated by the stir casting method. Exploratory work involved the fabrication of monolithic composites with varying Al2O3 contents (5-8 wt%) and hybrid composites with the ratios of Al2O3 (2-6 wt%) and Graphite (1-3 wt%) in matrix Al2024. For improving their dispersion, preheated reinforcement particles were introduced in matrix alloy at controlled stirring rates. A homogeneous particle distribution …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 823–836 Read article
-
Bio-Derived TPS–Lignin Hybrid Composites Reinforced with Modified Coir and Plantain Fibers for Eco-Efficient Structural Applications
Abstract: This study develops bio-derived polymer composites using a thermoplastic starch–lignin (TPS–lignin) matrix reinforced with alkali-treated coir and plantain fibers for sustainable load-bearing applications. The TPS–lignin matrix was formulated using cassava starch, glycerol, and 10 wt% lignin, while coir and plantain fibers were surface-modified using 5 wt% NaOH to enhance interfacial compatibility. Composite laminates were fabricated with varying fiber loadings (10–40 wt%) through melt-mixing and hot-press compression. Tensile, thermal, morphological, and …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 136–145 Read article
-
Mechanical Characterization of Prosopis Juliflora Fibre-Reinforced Epoxy Composites for Sustainable Automotive Applications
Abstract: This study investigates the potential of Prosopis juliflora (PJ) fibre as an eco-friendly, economical, and mechanically efficient reinforcement for epoxy-based polymer composites. Composite samples were produced using the compression moulding technique with epoxy-to-fibre weight ratios of 90:10, 85:15, and 80:20. Mechanical tests, including tensile, flexural, impact, and hardness evaluations, were conducted in accordance with relevant ASTM standards. The incorporation of PJ fibre resulted in significant improvements in the mechanical behaviour …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1720–1728 Read article
-
Performance Enhancement of COC-Modified LLDPE Films: Optimization of Stiffness, Tear Resistance, and Barrier through Plasma Surface Modification
Abstract: This study explores the development of high-performance packaging materials by blending commodity Linear Low-Density Polyethylene (LLDPE) with engineering cyclic olefin copolymer (COC) as a performance modifier. To leverage the processability of LLDPE alongside the structural rigidity of COC, blends were prepared at various weight ratios (95/05, 90/10, 85/15, and 80/20) using twin-screw melt extrusion, followed by the production of films and sheets via blown film extrusion and compression molding. The …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 128–143 Read article
-
Integrating Social Perception and Economic Valuation for Riparian Zone Preservation: Evidence from Kiliti Watershed, Ethiopia
Abstract: Riparian zones play a crucial role in maintaining watershed health by providing ecosystem services such as water filtration, erosion control, biodiversity conservation, and aesthetic and cultural benefits to surrounding communities. Despite their importance, riparian areas in many developing countries are increasingly degraded due to agricultural expansion, grazing pressure, and settlement encroachment. This study integrates social perception analysis with economic valuation to assess riparian zone preservation in the Kiliti Watershed, Northwestern …
Published in International Journal of Environmental Planning and Development Architecture · Vol. 4, Issue 1, 2026 · pp. 49–55 Read article
-
High-Performance Carbon Nanotube-Reinforced Biodegradable Polymer Composites for Packaging
Abstract: The growing issues concerning the properties of petroleum-based plastics on the environment increased the demand for biodegradable alternatives and polylactic acid (PLA) is one of the most promising options available. However, its poor toughness, thermal resistance, and barrier properties limit broader applications in sustainable packaging. This study reports the fabrication and characterization of PLA-based nanocomposites reinforced with carbon nanotubes (CNTs) at varying loadings (0.1-2 wt.%). Structural analysis (FTIR, XRD) confirmed …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 183–194 Read article
-
Corn Husk Fiber–Reinforced PLA Biocomposites: Mechanical, Thermal, and Biodegradation Performance
Abstract: The increasing environmental burden caused by conventional petroleum-based plastics has driven significant interest in the development of sustainable polymer composites reinforced with renewable natural fibers. In the present work, corn husk fiber (CHF), an agricultural waste by-product, was utilized as a reinforcing phase in a polylactic acid (PLA) matrix to fabricate eco-friendly biocomposites. Composite samples with varying fiber loadings (0–40 wt.%) were produced through twin-screw melt blending followed by compression …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 312–327 Read article
-
Artificial Intelligence-Assisted Multi-Objective Optimization of Agricultural Biomass-Reinforced Polymer Composites
Abstract: Agricultural biomass can reduce the environmental burden of polymer composites, yet its heterogeneous structure creates competing effects on strength, moisture resistance, density, and process ability. This study developed an artificial intelligence-assisted framework for balanced composite formulation. Experimental data of agricultural biomass reinforced polymer composites were gathered, harmonized and validated using leakage controlled validation. The mechanical and physical properties were predicted by artificial neural networks and conventional regression models. Explainable analysis …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 Read article
-
Ultrasonic Dispersion of Halloysite Nanotubes for Enhanced Mechanical, Thermal, and Morphological Performance of Epoxy Composites
Abstract: Halloysite nanotube (HNT)-reinforced epoxy nanocomposites were prepared by mixing HNT with bisphenol-A epoxy (LY 556) using ultrasonication, followed by compression molding. HNT contents of 0–5 wt.% were used. The composites were evaluated for tensile strength, flexural strength, Shore D hardness, Izod impact strength, and thermal stability using thermogravimetric analysis (TGA). The fractured tensile surfaces were also examined to understand the failure mechanism and interaction between HNT and the epoxy matrix. …
Published in Journal of Polymer & Composites · Vol. 14, Issue 5, 2026 Read article
-
The Symbiosis Between Spherical Refractive Error Cylindrical Refractive Error
Abstract: This study aimed to acknowledge the link between spherical refractive error and cylindrical refractive error, which is crucial for diagnosing and managing visual abnormalities productively. This research employed a multi-center, cross-sectional, analytical, and retrospective approach to investigate refractive errors. The objective results were refined subjectively to the best visual acuity with conventional clinical representations of refraction using the sphere, cylinder, and axis. The gathered data underwent analysis utilizing statistical software …
Published in Research and Reviews : A Journal of Medical Science and Technology · Vol. 13, Issue 1, 2024 · pp. 67–76 Read article
-
Strategic Enhancement of Composite Strength Explored Through Comprehensive Integration of Flax Fiber and Cenosphere in Epoxy Resin Matrices
Abstract: The Current research delves into the mechanical attributes of composite specimens, integrating flax fiber and cenosphere fillers within an epoxy resin matrix catalyzed by K-6 hardener. Executing a meticulous approach involving a vacuum bagging method and a specific formulation of 10 wt.% cenosphere, 50% epoxy resin, and 40% flax fibers, the study rigorously scrutinized tensile and flexural strengths. Notably, the first specimen exhibited a peak tensile strength of 94.329 MPa, …
Published in Journal of Polymer & Composites · Vol. 11, Issue 13, 2023 · pp. 199–217 Read article
-
Development of Novel Materials with Photocatalytic Effect
Abstract: For capturing solar energy and for converting it into electric power, it is utmost essential to design materials that can be used for this purpose. Generally, the materials deployed for converting solar energy into electric energy are sensitive to UV-radiation. If the material used for this purpose are sensitive to visible light, it will be the breakthrough research. It has been a challenge to design materials with novelty of being …
Published in International Journal of Photochemistry and Photochemical Research · Vol. 1, Issue 2, 2023 · pp. 25–39 Read article
-
Tribological Study on SiC+Graphene Reinforced Al319 Composite andOptimization of Stir Casting Parameters
Abstract: The aluminium 319 (Al319) is a commonly used material for fabricating automobile components. Due to continuous friction and vibration, those components are subjected to significant wear. Therefore, it is necessary to improve the wear characteristics of this Al319. Hence, in this study Silicon Carbide (SiC) and Graphene nanoparticles (GNPs) are reinforce to Al319 via electro-magnetic stir casting method to optimize wear characteristics without its affecting mechanical properties. Various proposition of …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 105–123 Read article
-
Wear Performance of Cylindrical Shaped Alumina Nanoparticles Filled Epoxy Composite
Abstract: Low cost high specific strength epoxy LY 556 and alumina nano filler is utilized in current research for developing a epoxy composite. A liquid dispersion method was adopted for fabricating epoxy alumina composite having 0.50 wt% of alumina reinforcement. For uniform and homogenous dispersion of reinforcement, ultra-sonification of 120 W is adopted. To study the effect of particle behavior, unfilled epoxy and 0.5 wt.% cylindrical alumina oxide filled epoxy composite …
Published in Journal of Polymer & Composites · Vol. 12, Issue 5, 2024 · pp. 94–100 Read article
-
Diglycidyl Ether of Bisphenol A (DGEBA) Based Epoxy Sizing Agent Induces Surface Polarity in Carbon Fibers†
Abstract: Determination of the chemical structure and composition of the sizing agent is a challenge as its concentration is low, varying in the range from ~0.5 wt.% (for polyacrylonitrile, PAN, based carbon fibers) to ~1 wt.% (for pitch-based carbon fibers). Moreover, such a piece of knowledge is vital for designing compatible polymer matrices to prepare CFRPs for diverse applications. As a result, the sizing layer that is coated on the carbon …
Published in International Journal of Crystalline Materials · Vol. 1, Issue 2, 2024 · pp. 24–34 Read article
-
Polymer-Based Transparent Conductive Composites for Flexible Solar Panel Coatings
Abstract: This study investigates the fabrication and characterization of polymer-based transparent conductive composites (PTCCs) tailored for flexible solar panel coatings using poly(methyl methacrylate) (PMMA) and poly(ethylene terephthalate) (PET) matrices reinforced with silver nanowires (AgNWs), multi-walled carbon nanotubes (MWCNTs), and PEDOT:PSS. The composites were synthesized through a solution blending and doctor-blade casting method followed by post-treatments to enhance interfacial bonding and conductivity. Optical transmittance values above 85% were achieved across all composite …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 99–110 Read article
-
ML-Based Predictive Modeling of Mechanical Properties in 3D-Printed Polymer Composites for IoT Applications
Abstract: This study aims to develop an interpretable and high-accuracy machine learning framework for predicting the mechanical properties of 3D-printed fiber-reinforced polymer composites, with a focus on structure–property correlations relevant to polymer processing and functional performance. Composite specimens based on PLA and ABS matrices were fabricated using FDM with varying weight fractions (5–20 wt%) of carbon and glass fibers. Standardized mechanical testing (ASTM D638, D256, D790) was performed to evaluate tensile …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 61–78 Read article