Search
644 articles for “Oxide”
-
Density and Interaction Data for Lutetium-Yttrium Ortho-Aluminate- Based Scintillation Crystals for Gamma-ray Spectroscopy and Imaging
Abstract: The density values of (LupY1-p) AP scintillators based on the results of a literature survey have been found strongly positively linearly correlated to the value of the parameter p, that represents the ratio of lutetium vs. yttrium oxides content by weight. Two cases of serious lack of information have been investigated to search reliable data. Further studies are in progress aimed at inferring possible unknown compositions by using the data …
Published in Journal of Nuclear Engineering & Technology · Vol. 12, Issue 2, 2022 · pp. 1–9 Read article
-
Characterisation of Plasma Sprayed CNT-Alumina Composite Coatings on Boiler Tube Steel
Abstract: In this research work, the 1.5, 2 and 4 wt.% CNTs-Al2O3 coatings were prepared and successfully deposited on T22 boiler tube steel using plasma spray process. Ni-Cr was also used as bond coat before applying CNTs-Al2O3 coatings. The coatings were subjected to metallography, XRD and SEM/EDAX analysis. The porosity of CNTs-Al2O3 mixed coatings on T22 boiler steel was found to be decreasing with increase in CNTs content. The CNTs were …
Published in Journal of Polymer & Composites · Vol. 5, Issue 3, 2017 · pp. 1–15 Read article
-
Depolymerization of Polypropylene: A Systematic Review
Abstract: AbstractPolypropylene have become an indispensable ingredient of human life and most widely used thermoplastic in commodity applications. Polymerization of propylene is carried out by using Ziegler-Natta or Metallocene catalysts, which results in high molecular weights and crystalline polypropylene which are not required for several applications. Reduction in molecular weight of polypropylene in conventional reactors is uneconomical and complicated. Therefore to overcome this problem researchers and technologists proposed a post reactor …
Published in Journal of Polymer & Composites · Vol. 4, Issue 2, 2016 · pp. 1–16 Read article
-
A Study on the Effect of Ionic Conductivity on Addition of Salt for Polymer Nanocomposite Gel Electrolyte for Solar Cell Applications
Abstract: AbstractDye sensitized solar cells (DSSC) have attracted greater attention in the recent years because of their relatively high energy conversion efficiency and low cost. In the DSSCs, the electrolytes play a vital role in the determination of the efficiency and long term stability. In this investigation, we report on the synthesis, characterization and conductivity study of polymer nanocomposite gel electrolyte. Cadmium oxide nanoparticles were added into polymer blend of poly …
Published in Journal of Polymer & Composites · Vol. 3, Issue 3, 2015 · pp. 8–15 Read article
-
Study of Mechanical and Thermal Properties of Unsaturated Polyester/CuO Nanocomposites
Abstract: AbstractThe CuO nano particles were synthesized from copper sulfate pentahydrate aqueous solution under the low hydrothermal condition at 80°C. The size of the CuO nanoparticles was calculated from TEM. FTIR spectra confirmed the formation of the CuO nanoparticles. Nanocomposites of unsaturated polyester resin with different loading of nano CuO fillers were prepared by casting method. The mechanical properties of the composites such as tensile behavior, flexural behavior, impact strength and …
Published in Journal of Polymer & Composites · Vol. 3, Issue 3, 2015 · pp. 35–42 Read article
-
A Review on Polysaccharide Based Nanocomposite Hydrogel Systems Fabrication Using Diverse Reinforcing Materials
Abstract: In current scenario, materials with better physicochemical properties are desirable to achieve quality life and sustainability. Polysaccharide/biopolymeric based hydrophilic systems owning to their inherent properties especially hydrophilicity, nontoxicity, biocompatibility have extended their approach in every streta of biomedical Sciences and replaced synthetic polymers upto great extent. Despite this they also experienced certain demerits due to their biological origin. Functionalization of polysaccharide based hydrophilic polymer with reinforcing materials /modulators especially in …
Published in Journal of Polymer & Composites · Vol. 8, Issue 1, 2020 · pp. 6–17 Read article
-
An Overview on Synthesis of Magnesium alloy based Metal Matrix Composites
Abstract: Magnesium alloy based composites are viewed as potential candidates for various applications in automobile, aerospace and defense sectors. Magnesium alloys majorly consisting of magnesium with fractional quantities of aluminum, zinc and manganese, are popularly used in light weight applications. This alloy can be reinforced with many of the ceramic oxides such as silicon nitride (Si3N4), Titanium carbide (TiC) etc in various forms to improve its mechanical and tribological properties. Currently …
Published in Journal of Polymer & Composites · Vol. 9, Issue 1, 2021 · pp. 1–6 Read article
-
Surface Engineering of Materials: A Review Based on Applications
Abstract: Surface characteristics of material play an important role for various applications. Like, there are many applications of the polymeric membranes in the fields of biomedical, filtration, food processing from the past few decades. But various problems have been faced in their applications due to bacterial and non-bacterial contamination on the surfaces. Many researchers have investigated the surface chemistry and roughness of the membranes to identify their properties and the difficulties …
Published in Journal of Polymer & Composites · Vol. 9, Issue 2, 2021 · pp. 45–56 Read article
-
Enhanced Thermal Conductivity of Polyaniline Nanofluids Synthesized using CuCl2 as Catalyst
Abstract: AbstractThe development of nanofluids for enhancing the heat transfer properties over the conventional fluids is mainly hindered by a vital issue of dispersion stability and hence is being explored in the present work. In the present study, Copper Polyaniline nanoparticle was synthesized by the oxidative polymerization method using CuCl2 as a catalyst. The characterization of Copper Polyaniline was performed. The sizes of nanoparticles were found to be within 7.24 nm …
Published in Journal of Polymer & Composites · Vol. 11, Issue 1, 2023 · pp. 20–40 Read article
-
Effect of Curing Time on Physico-mechanical Properties on Dental Composite
Abstract: This study aim to investigate the influence of curing time on physical and mechanical properties of a dental composite cured by using LED light with intensity of 1500 mW/cm2 in the range of 440-480 nm. We prepared the glass ionomer powder by fusion of various inorganic components at high temperature and studied the influence of silica/alumina ratio keeping other inorganic salts such as Calcium fluoride (CaF2), Sodium Fluoride (NaF), Calcium …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. 36–47 Read article
-
An Investigation into the VariablesInfluencing the Densification of Spark Plasma Sintered, 40 Weight Percent Ni-Fe Nano Powder
Abstract: The mechanical alloying process that included high-energy ball milling resulted in particle sizes of 25 mm and 80 mm on average for the Ni-Fe alloy that included 40 percent Ni. At room temperature, highenergy planetary ball milling was carried out over timespan ranging from 15 hours to 60 hours. All of the samples were sintered at the same conditions, which included a temperature of 650 degrees Celsius and a pressure …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. 29–35 Read article
-
Nanomaterials and Their Effects on the Environment: Analyzing Widespread Use
Abstract: Due to the need and uses of nanoparticles in a wide variety of fields of human activity, including industry, agriculture, commerce, medical, and public health, there has been a significant uptick in interest in nanotechnology among the general populace. Because of the inevitability of environmental exposure to nanomaterials as a consequence of their increasing incorporation into our everyday lives, more and more focus is being placed on the study of …
Published in Journal of Polymer & Composites · Vol. 11, Issue 1, 2023 · pp. 97–103 Read article
-
Estimation of Mechanical Properties of Kevlar/Basalt Intrawoven Composite Laminates Containing Nanoparticles
Abstract: Purpose: The research describes estimation of various Mechanical properties like compression, tensile, shear and impact strength of Kevlar/Basalt (KB) Intrawoven 1×1 composite laminates, each comprising 1%, 3% and 5% of Al2O3 (Aluminium oxide) nanoparticles. Design/methodology/approach: These are woven with the help of manual handloom weaving machine, compression moulding technique was adopted for the fabrication of hybrid composite laminates. Attempts have been made to analyse the mechanical properties of Kevlar/Basalt intrawoven …
Published in Journal of Polymer & Composites · Vol. 11, Issue 2, 2023 · pp. 1–12 Read article
-
Influence of SiO2 Nanoparticles on the Structural, Morphological, and Optical Properties of CsPbBr3 Quantum Dots
Abstract: This work mainly investigates the structural and optical property differences between CsPbBr3/SiO2 quantum dots (QDs) and CsPbBr3 QDs thin films deposited on fluorine-doped tin oxide (FTO) glass. X-ray diffraction of CsPbBr3/SiO2 QD thin film showed a polycrystalline cubic nanostructure with (200) as a dominant phase and did not show any peak of SiO2. Scanning and transmission electron microscopy images show that it is very small spherical or semi-spherical particles with …
Published in Journal of Polymer & Composites · Vol. 11, Issue 2, 2023 · pp. 62–69 Read article
-
Prospects of Shale gas in India verses Global Scenario and Future of Plasma Pulse Technology
Abstract: Conventional sources are expensive, polluting and limited by its reserves so, it will not be able to meet the demand of a country which is increasing continuously. This concern triggered the scramble to secure long term oil supplies and shown their reliance on the unconventional resources. Shale gas is natural gas trapped in the shale formation with organic rich content of methane. Huge reserves have been found in United States, …
Published in Journal of Petroleum Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 35–43 Read article
-
Nanoparticle Reinforced Base Material Thermal Properties Using Numerical Model: A Review Paper
Abstract: Present paper deals with the review of the analysis of base materials thermal properties. Nanoparticles are reinforced into the base material to analyse their thermal properties using different numerical models. Mixture rule and Maxwell model are considered to analyse the thermal properties of Al6061/Al7075 base material thermal properties reinforced with silicon carbide, aluminium oxide and copper nanoparticles. From the analysis, it has been found that addition of the nanoparticles into …
Published in Journal of Production Research & Management · Vol. 9, Issue 2, 2019 · pp. 9–11 Read article
-
Use of Alternative Fuels in Indian Cement Industry: A Review
Abstract: The making of Portland cement is an energy concentrated process. It produces significant pollution and uses huge amounts of non-renewable energy. With growing pressures to cut greenhouse gas emissions due to cement manufacture, research and expansion of fuel alternatives and their effect on the manufacturing process have become an industry focal point. The intrinsic properties of sintering cement in a rotary kiln allows for a large number of fuels to …
Published in Journal of Production Research & Management · Vol. 10, Issue 1, 2020 · pp. 32–39 Read article
-
Metal Foam by Powder Metallurgy Routes: A Review Paper
Abstract: The aim of study is to evaluate and optimize the process parameters and several control factors of foaming because of their physical and mechanical properties such as, high stiffness, high compressive strength, and good energy absorption. Powder metallurgy is a method in which aluminum and aluminum alloy are mixed with TiH2 or other blowing agents for foam making process. Powder mixed is consolidated to obtain a high dense foam compact …
Published in Journal of Production Research & Management · Vol. 6, Issue 1, 2016 · pp. 9–15 Read article
-
Design and Analysis of Inverters using Double Gate MOSFET
Abstract: AbstractThe double gate MOSFET is a form of MOSFET where two gates are fabricated along the length of the channel, one after another. There are several applications of double gate MOSFETs. It is possible to design logic gates using double gate MOSFETs. It is one of the digital applications of it. This paper interprets the design and analysis of different types of inverters using DG-MOSFET. The advantages of using DG-MOSFET …
Published in Journal of Semiconductor Devices and Circuits · Vol. 4, Issue 1, 2017 · pp. 1–7 Read article
-
Simulation Study of Process Variations in Double Gate Junctionless Field-Effect Transistors
Abstract: This work discusses the process variations in symmetrical double-gate (DG) junctionless (JL) field-effect transistors (FETs) by device simulation. Output I-V characteristics along with subthreshold slope increase, DIBL variations with drain voltage and threshold voltage shift variations are systematically analyzed with the general variability issues including oxide thickness, channel thickness and doping concentration. Potential distribution in the body channel region is also analyzed. Optimum values of the variability factors are considered …
Published in Journal of Semiconductor Devices and Circuits · Vol. 2, Issue 2, 2015 · pp. 18–27 Read article