Search
334 articles for “categories”
-
Seismic Behavior of RCC Buildings under Revised Seismic Zone Classification by BNBC
Abstract: This study aims at the comparison of provisions of earthquake analysis given BNBC 2017. The revised BNBC 2017 has divided the seismic zones of Bangladesh into four different categories such as Zone-1, Zone-2, Zone-3 and Zone-4 respectively. They have different seismic zone coefficients. Finally structural analysis and design of a typical G+10 storey school building situated in all four seismic zones is conducted to investigate the seismic behavior of that …
Published in Recent Trends in Civil Engineering & Technology · Vol. 9, Issue 3, 2019 · pp. 21–28 Read article
-
Experimental Investigation on Concrete with Replacement of Fine Aggregate from Scrap Tyre Rubber Dust
Abstract: Concrete is the most widely used construction material in the world in which cement and aggregates are the main constituents. This has led to continuous and increasing demands of natural materials used in the construction. Present study aims to explore the potential utilization of scrap tyre rubber in various Portland cement concrete categories for the production to study the structural behaviour of concrete, and to help partially solving environmental problem …
Published in Recent Trends in Civil Engineering & Technology · Vol. 7, Issue 2, 2017 · pp. 5–9 Read article
-
Stabilization of Black Cotton Soil with Blending of Coir Fiber
Abstract: Stabilization of soil is a major challenge in civil engineering. About 20 % of land area in India is covered by black cotton soil. Structures built on black cotton soil may be damaged because of high swelling and shrinkage characteristics of this soil with variation of water content. Black cotton soil is an expansive soil which loses its strength in presence of water. On the other hand, it reflects behavior …
Published in Recent Trends in Civil Engineering & Technology · Vol. 5, Issue 2, 2015 · pp. 8–11 Read article
-
Analysis of Three Types of Quartzite as Coarse Aggregate Material and their Impact on Compressive Strength on Concrete
Abstract: Aggregates are the most important constituents of concrete. They give body to the concrete, reduce shrinkage, enhance strength and effect economy. The quartzite rock available in Delhi is a prominent geological material available in the entire Aravali range. Most of the manufacturing of concrete is going on using quartzite as aggregate material. However, three different categories of quartzite have been classified on the basis of its colour composition namely greyish …
Published in Recent Trends in Civil Engineering & Technology · Vol. 7, Issue 1, 2017 · pp. 1–8 Read article
-
Construction Phase Sustainability Index of Building
Abstract: The construction industry provides infrastructure, scope of job to society across the world. Apart from these benefits, the construction industry has some negative impacts on society and the environment. This industry is considered to be the major user of electricity and fresh water. It is also considered to be one of the major emitters of greenhouse gasses during the construction period. Across the world, there are many rating systems to …
Published in Recent Trends in Civil Engineering & Technology · Vol. 12, Issue 3, 2022 · pp. 31–50 Read article
-
Power Quality Enhancement in Distribution System using D-STATCOM
Abstract: New solutions based on power electronics have been developed to safeguard commercial and industrial clients against power quality issues on the electrical distribution system, referred to as Custom Power Products. Custom power devices are classified into three categories by their structures such as dynamic voltage regulator (DVR), distribution static compensator (STATCOM) and unified power quality compensator (UPQC).The Distribution Static Compensator (D-STATCOM), one of the custom power product, is a shunt-connected …
Published in Recent Trends in Electronics Communication Systems · Vol. 8, Issue 2, 2021 · pp. 17–22 Read article
-
A Review on Leak Detection Techniques in Water Distribution Systems
Abstract: AbstractWater is an important resource. Water distribution network (WDN) which includes pipes is used to transport water from water treatment plants to homes. Every water distribution system (WDS) fails partially or completely during its lifetime. This paper gives the in-depth review of leakages caused in WDS. It provides the overview of various techniques implemented towards the occurrence and localization of leaks. This paper organized and classified the techniques into different …
Published in Recent Trends in Fluid Mechanics · Vol. 5, Issue 2, 2018 · pp. 23–29 Read article
-
Design and Fabrication of an Arduino based Automatic Waste Segregator
Abstract: AbstractToday waste has become one of the biggest problem in the ecosystem due to the way people dispose it. Garbage is usually buried or burnt. These methods of disposal further worsen the state of environment. The solution to this problem can be recycle and reuse. Segregation is the most important step for the waste treatment. Diverse waste materials have to be treated in different ways. It can be segregated as …
Published in Recent Trends in Sensor Research & Technology · Vol. 6, Issue 3, 2019 · pp. 1–5 Read article
-
Various Routing Algorithms in Wireless Sensor Networks for Energy Minimization
Abstract: The past few years have witnessed increased interest in the potential use of wireless sensornetworks (WSNs) in a wide range of applications and it has become a hot research area. Lot ofresearchers are showing interest in WSN for disaster management where prediction ofupcoming disaster is required well in advance before it happens and in critical areas wherehuman presence is not possible directly; wired communication dose not suit well for suchapplications. …
Published in Recent Trends in Sensor Research & Technology · Vol. 7, Issue 3, 2020 · pp. 26–37 Read article
-
Analysis of Doubly Fed Induction Generator with Effect of Various Design Parameters
Abstract: Increasing demand for electricity requires developing new generation techniques which fulfil the demand and keep the environment clean. As per the survey, in the category of renewable energy, wind power plants play an important role in the power generation. In the wind energy generation system, a doubly fed induction generator (DFIG) is more popular. In this paper, the performance of DFIG investigated with different design parameters. Study the effect of …
Published in Trends in Electrical Engineering · Vol. 8, Issue 2, 2018 · pp. 10–18 Read article
-
On The Energization and Steady-State Performance of 6-Pulse Diode Bridge Rectifiers Supplying Constant Voltage Loads
Abstract: The paper addresses the analysis of 3-phase 6-pule diode bridge rectifier circuits supplying a special load category representable by constant voltage sources. The applied Mathematica-based solution technique can handle symmetrical and unsymmetrical 3-phase voltages. The presented results include the phase currents on the AC side as well as the magnitude and wave shape of the output current on the DC side. Several case studies demonstrating the impact of the source’s …
Published in Trends in Electrical Engineering · Vol. 11, Issue 1, 2021 · pp. 14–23 Read article
-
A Review on STATCOM Controller for Power Quality Enhancement in Distributed System
Abstract: New technologies, using power Electronics-based concepts, have been Developed to provide protection for Commercial and industrial customers from Power quality problems on the electrical Distribution system known as Custom Power Products. Custom power devices are classified into three categories by their structures such as dynamic voltage regulator (DVR), distribution static compensator (STATCOM) and unified power quality compensator (UPQC).The Distribution Static Compensator (D-STATCOM), one of the custom power product, is a …
Published in Trends in Electrical Engineering · Vol. 11, Issue 2, 2021 · pp. 24–29 Read article
-
A Review of Dynamic Wireless Charging System for Electric Vehicles and IoT Technology
Abstract: Dynamic charging of Electric Vehicles (EVs) by Wireless Power Transfer (WPT) is a key emerging technology in the field of power electronics. Even though Electric vehicles (EVs) are beneficial to the environment, they have their own limitations with respect to charging difficulties and mileage anxiety. These problems are overcome by dynamic wireless power transfer (DWPT) technology. By DWPT technology the size of the main storage battery can be reduced, significantly …
Published in Trends in Electrical Engineering · Vol. 13, Issue 2, 2023 · pp. 59–68 Read article
-
Optimization of Helical Spring Weight using Meta-heuristic Algorithms
Abstract: Optimization is the act of obtaining the best results under given circumstances. A mathematical theory of optimization is highly in use and is being applied to design where design function can be expressed mathematically. Many techniques like Linear Programming, Branch & Bound technique, Dynamic Programming methods are available to solve optimization problems. But these conventional Methods suffer from certain drawbacks like sticking at suboptimal solution, inefficiency in handling problems having …
Published in Trends in Machine design · Vol. 5, Issue 2, 2018 · pp. 21–28 Read article
-
Modern perspectives on composite armor
Abstract: This article is study of garment oriented schemes to learn composite armor. Bulletproof armor has been developed to protect humans from destructive weapon. Assess has been to develop low-cost, easy in fabricate originated easy wearable biocompatible bulletproof garment. Suggestive estimation has scriptive issued competence between variations in plate thickness and amount of energy absorbed by lamination of armor. Henceforth, observation has been 12mm thickness of composite plate lying to be …
Published in Trends in Machine design · Vol. 8, Issue 3, 2021 · pp. 14–20 Read article
-
Evaluation of Pulley Performance, Pulley Machine, and its Benefits and Drawbacks
Abstract: A rope is simply looped over a grouping of one or more wheels to create a pulley, which makes it simpler to lift anything. The force exerted by the body can be effectively multiplied by the use of a pulley. A wheel with a flexible rope, rope, cable, chain, or belt on its rim is referred to as a "pulley.". It is simpler to raise objects when using pulleys since …
Published in Trends in Machine design · Vol. 9, Issue 2, 2022 · pp. 12–16 Read article
-
Multi-way Protection Scheme to Handle Multiple Failures for Cost-Efficient Fiber-Wireless (FiWi) Access Networks
Abstract: AbstractFiber Wireless (FiWi) access networks prove themselves as promising broadband access networks. These networks enable users to access services in “Anywhere-Anytime” fashion. FiWi networks offer higher bandwidth and better flexibility at much lower price than passive optical network. As FiWi supports high data rate (typically about Gigabits per second), any failure may results in huge data loss. Therefore, to protect such loss of data, we need to design a more …
Published in Trends in Opto-electro & Optical Communication · Vol. 5, Issue 3, 2015 · pp. 1–15 Read article
-
Evolving Perspectives: Innovations in Object Detection and Identification
Abstract: One of the most important developments in computer vision has been the creation of object detection and identification systems, which have allowed robots to perceive and understand visual data similarly to humans. These systems locate each object by drawing a bounding box around it, in addition to detecting and classifying every object in an image or video. This study suggests a novel method for item identification and detection that makes …
Published in Trends in Opto-electro & Optical Communication · Vol. 13, Issue 3, 2023 · pp. 23–27 Read article
-
Innovative Risk Aperture Manipulation Model for Risk Management in Mega Project Construction
Abstract: The complexities associated with the technical, managerial and financial interventions in mega project implementation accommodates greater risks, encapsulating the complete project period from inception to closure. Consideration of risks in mega project scope is of paramount importance as it delineates either threat or opportunity in the guise of uncertainty at each and every phase of the project. The absence of innovative and rigorous risk management structure imparts a perplexing scenario …
Published in Trends in Transport Engineering and Applications · Vol. 2, Issue 1, 2015 · pp. 11–24 Read article
-
Review of Simulation Techniques for Microscopic Mobility of Pedestrian Movement
Abstract: Simulation techniques are very useful for developing models or systems over time torepresent the real-world scenarios. The model represents the key characteristics orbehaviors/functions of the selected physical or abstract system or process. Simulationtechniques are useful when the real system cannot be engaged, because of inaccessibility,or dangerous or is unacceptable to engage or does not exist. Microscopic characteristicsof pedestrian traffic consider speeds, walking directions, distances between pedestrians,relative positions, passing behavior and …
Published in Trends in Transport Engineering and Applications · Vol. 1, Issue 1, 2014 · pp. 27–45 Read article