Search
375 articles for “Al alloy”
-
Studies on Erosion Wear Behavior of Aluminum-3 Magnesium-10 Silicon Carbide Composite
Abstract: Aluminum-based metal matrix composites (MMCs) offer potential for advanced structural applications when high specific strength and modulus as well as good elevated temperature resistance along with light weight are important. In the present work, aluminum alloy-silicon carbide composite (Al-3Mg-10SiC) is developed using the stir-casting technique and is subjected to study the wear behavior. Solid particle erosion on Al-3Mg-10SiC was conducted. Implementation of design of experiments (through Taguchi and statistical techniques) …
Published in Journal of Materials & Metallurgical Engineering · Vol. 3, Issue 3, 2013 · pp. 39–50 Read article
-
An Investigation on Effect of Welding Current Mode on Weld Quality Characteristics of Microplasma Arc Welding of Inconel 625 Sheets
Abstract: Nickel alloys have gathered wide acceptance in the fabrication of components, which require high temperature resistance and corrosion resistance, such as metal bellows used in expansion joints in aircraft, aerospace and petroleum industry. In case of single-pass welding of thinner sections of this alloy, pulsed current microplasma arc welding was found beneficial due to its advantages over the conventional continuous current process. The paper focuses on studying the effect of …
Published in Journal of Materials & Metallurgical Engineering · Vol. 3, Issue 2, 2013 · pp. 8–13 Read article
-
Fabrication of AA5182-Semis for Precise Components
Abstract: Al4.5MgMn alloy is known to show an excellent physical and mechanical properties as well as manufacturing and fabrication ease as semis, suitable for making precise components like hull of the light weight vehicles and seamless tubes. Present work has tried to describe the development of microstructure and texture of an industrial tandem hot rolled Al4.5MgMn alloy sheet after laboratory cold rolling and annealing. Crystallographic orientation dependent strengthening rate has been …
Published in Journal of Materials & Metallurgical Engineering · Vol. 11, Issue 3, 2021 · pp. 21–32 Read article
-
Compatibility Issues of Heat Pipes for Radioactive Exposures
Abstract: AbstractSelection of alloys are refractory materials those withstand high temperature, radioactive embrittlement effects for long periods. Effects of high temperature and neutron embrittlement are subjects considered in this article. Effects of coolants, reactive gases like oxygen are facts of importance to select materials for reactor construction system. Selections of radioactive protecting alloys like sleeves are of importance to produce systems within margins of weight. Compatibilities have been decisive among material, …
Published in Journal of Nuclear Engineering & Technology · Vol. 9, Issue 3, 2019 · pp. 24–32 Read article
-
Synthesis and formability of Al/(Fe-Mn) particulate compositeusing stir casting
Abstract: Demand for lightweight and fuel economy by automotive and aircraft industries focuses to explore different materials. Alloys and composites developed with same objective to obtain superior desired mechanical properties compatible for such intended applications. However, alloy consider as solid solutions with metallic properties and cannot mix with primary major element in random proportions. This forced researcher community to develop composites, which are heterogeneous solid solutions or multi-phase materials comprising matrix …
Published in Journal of Polymer & Composites · Vol. 10, Issue 1, 2022 · pp. 80–88 Read article
-
An Investigation into the VariablesInfluencing the Densification of Spark Plasma Sintered, 40 Weight Percent Ni-Fe Nano Powder
Abstract: The mechanical alloying process that included high-energy ball milling resulted in particle sizes of 25 mm and 80 mm on average for the Ni-Fe alloy that included 40 percent Ni. At room temperature, highenergy planetary ball milling was carried out over timespan ranging from 15 hours to 60 hours. All of the samples were sintered at the same conditions, which included a temperature of 650 degrees Celsius and a pressure …
Published in Journal of Polymer & Composites · Vol. 10, Issue 3, 2022 · pp. 29–35 Read article
-
Microstructure and Mechanical Characterization of AA390 and Si3N4 Metal Matrix Composite Using Severe Plastic Deformation
Abstract: Metal matrix composites (MMCs) have significant attention in recent years due to their potential for improved mechanical properties compared to conventional monolithic materials. This study focuses on the microstructure and mechanical characterization of a MMC comprising AA390 aluminum alloy reinforced with Si3N4 particles. The severe plastic deformation (SPD) process, Equal Channel Angular Pressing (ECAP), was employed to fabricate the composite with enhanced mechanical properties. The ECAP method was chosen as …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 17–30 Read article
-
Design and Analysis of Automobile Hood
Abstract: Bonnet is a main component of front portion of a car one which is used for many purposes. It is usedto decorate the car and add luxurious look. Bonnet is made in aerodynamic shape to reduce airresistance. Bonnet generally used to cover car engine. Therefore, the bonnet system is an accesspanel to the engine compartment to enable maintenance of power train, drive belts, battery, fluidlevels and lamp units, and it …
Published in Journal of Production Research & Management · Vol. 11, Issue 1, 2021 · pp. 42–52 Read article
-
Fractural Mechanics Crack Propagational Study on Different Material And Different Crack Location of weld joint in ANSYS
Abstract: AbstractThere have been spectacular failures made of ductile material. The structure as whole will remain as brittle only until the load is applied it will have elastic response it will not have plastic response. But near the crack tip there will have plastic zone and plastic zone indicates flow crack is going to behave for the present study analysis is carried out on crack near weld joint and three different …
Published in Journal of Structural Engineering and Management · Vol. 5, Issue 3, 2018 · pp. 29–33 Read article
-
Comparative studies of Oxidation and hot corrosion behaviors of uncoated and detonation gun sprayed Cr3C2-25NiCr coating on SA-213 boiler steel at 8000C
Abstract: Fe-based alloys suffer oxidation and hot corrosion when the surfaces were in contact with air (oxidation) as well as the salty atmosphere (Hot corrosion) at elevated temperatures. In these atmospheric conditions, non-protective oxide Fe2O3 was formed on the surface of alloys. Oxidation and hot corrosion have been recognized as a major problem in the applications of the diesel engine, boilers, gas turbines, and chemical power plant etc. Detonation-gun sprayed Cr3C2-25NiCr …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 6, Issue 1, 2019 · pp. 17–22 Read article
-
Autonomous Optimization, Method Design of Casting and Its Experimental Validation: A Case Study
Abstract: The metal casting is a complicated but a mass production manufacturing technique. But on the otherhand, the chances of casting rejection are also more if proper attention is not made at every stage ofcasting production. In the metal casting process, higher yield and minimum defects level are expectedby the foundry industries. In the present global and competitive world metal casting industries needsto perform efficiently with a reduction in rejections. This …
Published in Trends in Machine design · Vol. 8, Issue 1, 2021 · pp. 1–10 Read article
-
A REVIEW ON RECENT TRENDS AND CHALLENGES IN MICROMACHINING AND MACHINABILITY OF Ti-6Al-4V
Abstract: Based on several literature examinations from past decades, it is clearly observed that limited research has been done till date concerning to micromachining and had a partial understanding of it with focus on miniaturized parts. This review article presents a complete comprehensive on machining process at micro level with attention in drilling for work horse of titanium alloys. The Ti and its alloys are the most attractive materials due to …
Published in Trends in Mechanical Engineering & Technology · Vol. 8, Issue 3, 2018 Read article
-
A Review on Recent Trends and Challenges in Micromachining and Machinability of Ti-6Al-4V
Abstract: Based on several literature examinations from past decades, it is clearly observed that limited research has been done till date concerning to micromachining and had a partial understanding of it with focus on miniaturized parts. This article presents a complete comprehensive review on machining process at micro level with attention in drilling for work horse of titanium alloys. The Ti and its alloys are the most attractive materials due to …
Published in Trends in Mechanical Engineering & Technology · Vol. 9, Issue 1, 2019 · pp. 7–31 Read article
-
A Study of Macrostructure and Wear Behavior of AL7075-B4C MMC Using DoE Method
Abstract: Metal matrix composites are advanced materials produced by combining two or more constituents. In that the major phase called matrix alloy and the other is, generally, ceramic reinforcement. AA7075- B4C Composites are popular in automotive, aerospace and defense fields because of their high strength-to-weight ratio, wear resistance, etc. Present work is focused on the study of wear behavior of Aluminum 7075 Alloy with B4C composites prepared by using Stir Casting …
Published in Trends in Mechanical Engineering & Technology · Vol. 9, Issue 2, 2019 · pp. 25–32 Read article
-
A Review on Shielded Metal ARC Welding
Abstract: Shielded metal arc welding (SMAW) is the world's most popular welding process. In this process consumable electrode is used for generating arc. The electrode is coated with a shielding flux. The flux melts with the electrode metallic core, forming gas and slag, shielding the arc and the weld pool. The flux cleans the metal surface and protects the molten metal from oxidation and stabilizes the arc. The molten electrode metal …
Published in Trends in Mechanical Engineering & Technology · Vol. 10, Issue 1, 2020 · pp. 1–5 Read article
-
Application of Smart Material Technology: A Review
Abstract: These days, smart materials are employed in every aspect of technology and human life. Much work is being done to explore their potential in different engineering applications that could benefit the average person. Shape memory alloys, piezoelectric materials, magneto rheological materials (MR), and electro rheological materials (ER) are just a few examples of the many diverse kinds of smart materials. The electric supply can be adjusted to change the viscosity …
Published in Trends in Mechanical Engineering & Technology · Vol. 14, Issue 1, 2024 · pp. 34–39 Read article
-
Use of Gold in Crown and Bridge Procedures: The Most Versatile Restorative Material in Dentistry: A Review and Commentary
Abstract: Use of gold restorations has been almost forgotten in dentistry. They are no longer a part of most dental training curricula or often employed in private practice. Gold restorations are usually overlooked on most patient treatment plans in modern dentistry largely due to the following misconceptions: Gold is too expensive for use as a dental material. Nonetheless, the price of an ounce of gold in recent months has been at …
Published in Research and Reviews: A Journal of Dentistry · Vol. 7, Issue 1, 2016 · pp. 36–40 Read article
-
Allergies to Materials used in Orthodontics
Abstract: In orthodontics allergy from alloys, particularly nickel, has been broadly studied and a number of other case reports of nickel-induced contact dermatitis have been reported. The evidence suggests that the foremost common allergy reported in orthodontics is said to be nickel in orthodontic appliances and allergic response is more commonly seen in women due to a previous exposure from nickel in jewelry. During the course of orthodontic treatment it has …
Published in Research and Reviews: A Journal of Dentistry · Vol. 11, Issue 2, 2020 · pp. 1–7 Read article
-
A Study on Chemical Composition in Temperature Sensor
Abstract: As the demand for precision thermal monitoring in extreme environments – such as aerospace propulsion systems and micro-electromechanical systems (MEMS) – continues to escalate, the chemical stability of temperature sensing elements has become a critical focal point. This study investigates the correlation between the chemical composition of thin-film resistance temperature detectors (RTDs) and their operational longevity under thermal cycling. By employing X-ray Photoelectron Spectroscopy (XPS) and Energy-Dispersive X-ray Spectroscopy (EDS), …
Published in Journal of Nanoscience, NanoEngineering & Applications · Vol. 16, Issue 2, 2026 · pp. 1–7 Read article
-
Fatigue Analysis of the FSAE Vehicle's Front Wheel Hub
Abstract: This study illustrates the design and analysis of the FSAE vehicle's front wheel hub. Because wheel hubs are subjected to cyclic loads on a continuous basis, there is a risk of fatigue, which leads to material failure. The start and spread of cracks in a material as a result of cyclic loading is known as fatigue. The brake discs could not be easily removed since the disc is positioned between …
Published in Journal of Automobile Engineering and Applications Read article