Search
35 articles for “variable working speed”
-
Cost Effective Automatic Garage Door Mechanism With Variable Speed
Abstract: The aim of our project is to provide safety as well as security to people from the largest electromechanical objects which are available at home. An automatic garage door mechanism was selected as a subject of our research as it is the complex electro-chemical object at home. As technology increases day by day every households installs this automatic garage door mechanism. The major problem with the conventional garage door system …
Published in Journal of Automobile Engineering and Applications · Vol. 8, Issue 1, 2021 · pp. 1–5 Read article
-
A Study on Chatter Marks in Crankshaft Pin Grinding Process Using Taguchi Technique
Abstract: Crankshaft pin grinding is a vital machining process in automotive industry. It is a finishing operation to the crankshaft of the engine, which if neglected could lead to a significant cost to the manufacturer of warranty claims. The study aims at identifying significant process parameters that are influencing the chatter marks and also setting the process parameters of the machine to get a good quality product. Chatter marks are the …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 1, 2018 · pp. 1–5 Read article
-
Optimizing Machining Parameters for Surface Roughness and Metal Removal Rate While Turning of Aluminium Based Metal matrix Composite
Abstract: Nowadays demand of lightweight materials is increasing tremendously and aluminum based metal matrix composite (MMC) plays important role to fulfill such demands due to characteristics like lightweight and high strength. This work is intended to investigate the effect of the variables like speed, feed and depth of cut, on surface roughness and MRR. This work is carried out on Aluminum based MMC with 10% of boron carbide (B4C). Taguchi’s L27 …
Published in Journal of Mechatronics and Automation · Vol. 6, Issue 3, 2019 · pp. 42–48 Read article
-
Maximum Power Point Tracking of a Variable Speed Permanent Magnet Synchronous Generator Based Wind Energy Conversion System
Abstract: Wind turbines produce maximum power at the optimal tip-speed ratio. Fixed speed wind turbines are inefficient because the turbine blades rotate at a specific mechanical speed irrespective of the prevailing wind speed. The system is therefore, not able to extract the maximum possible amount of power. In this work, a maximum power point tracking scheme for a variable-speed permanent magnet synchronous generator based wind energy conversion system is implemented in …
Published in Journal of Power Electronics and Power Systems · Vol. 5, Issue 3, 2015 · pp. 35–51 Read article
-
Design of Front-end for Variable-frequency Drive
Abstract: A variable-frequency drive (VFD) is a device used in electro-mechanical drive systems to regulate the speed and torque of AC motors. It consists of a rectifier, a DC link, and an inverter, which work together to convert AC power into a variable frequency and voltage AC power supplied to the motor. By providing accurate speed regulation, VFDs enable energy conservation, enhanced process management, and reduced motor wear. They are commonly …
Published in Research & Reviews: A Journal of Embedded System & Applications · Vol. 11, Issue 1, 2023 · pp. 31–35 Read article
-
Control of a Grid-Connected Variable Speed Permanent Magnet Synchronous Generator Based Wind Power Generation System
Abstract: Variable speed wind turbines are more efficient compared to their fixed speed counterparts since maximum power is extracted over a wide range of wind speeds. In this work a grid-connected wind power generation system is modeled and implemented in Matlab/Simulink using a permanent magnet synchronous generator. A back to back space vector pulse width modulated voltage source converter converts the variable frequency generator currents and voltages into DC, then back …
Published in Journal of Power Electronics and Power Systems · Vol. 6, Issue 2, 2016 · pp. 8–24 Read article
-
Experimental Investigation on Mechanical Characterization of Electrodeposited Shot Peened Copper Coated and Un-Coated Mild Steel
Abstract: The fatigue strength of fabricated copper coating on mild steel specimens under repeated loading and the overall number of cycles to failure has been investigated. The specimens of copper coating on mild steel substrate are fabricated by using an electro deposition shot peening method. The hardness behaviour of fabricated specimens studied and the experimental work has been carried out by using Vickers Micro Hardness under the load of 20N force. …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 279–288 Read article
-
Experimental Investigation into Surface Roughness of Polished Zinc Plate with Ultrasonic Vibration Using Single Pole Magnetic Abrasive Finishing
Abstract: This research investigates how applying ultrasonic vibrations influences the surface finish quality of zinc plates when using the Single Pole Magnetic Abrasive Finishing (SP-MAF) method. In SP-MAF, magnetic abrasive particles (MAPs)—amalgamation of ferromagnetic and abrasive materials—are guided by a magnetic field to achieve precise surface finishing. Introducing ultrasonic vibration improves the effectiveness of the flexible magnetic abrasive brush (FMAB), which forms as the MAPs align along the magnetic field lines. …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1166–1178 Read article
-
Investigation of Mechanical Properties of Friction Stir Welded AA6063 Joints
Abstract: Friction Stir Welding is often referred as the joining technology of next generation because of its multiple advantages over the existing conventional processes. It is a solid state joining process which is free from the requirement of filler wire, consumable material, harmful gaseous emissions and also provides smooth surface with better surface finish. Moreover since no third additive material is involved hence, the microstructure of the welded joint also bears …
Published in Journal of Industrial Safety Engineering · Vol. 4, Issue 2, 2017 · pp. 1–4 Read article
-
Dynamic Simulation of Load-Responsive Vapor Compression Refrigeration Systems
Abstract: Because of their dependable operation and effectiveness, vapor compression refrigeration systems, or vapor compression refrigeration (VCRS), have become popular in commercial, industrial, and residential settings. However, under different thermal loads, classic vapor compression refrigeration (VCR) systems may perform less well in that they are usually built for steady-state conditions and run at consistent speeds. In order to improve a load-responsive VCR system’s flexibility, energy efficiency, and response to changing cooling …
Published in Journal of Refrigeration, Air conditioning, Heating and ventilation · Vol. 12, Issue 2, 2025 · pp. 32–37 Read article
-
DC Motor Control using Deep Reinforcement Learning for Enhanced Robustness and Precision
Abstract: DC motors remain the workhorse of industrial automation and mobile robotics, but achieving simultaneous high-speed transient response and negligible steady-state error under variable load conditions continues to challenge classical Proportional-Integral-Derivative (PID) controllers. These model-dependent systems often require extensive tuning and struggle to maintain optimal performance when confronted with parametric uncertainties, non-linear friction, or sudden voltage fluctuations. This study presents a novel, model-free control paradigm utilizing Deep Reinforcement Learning (DRL)—specifically, a …
Published in International Journal of Electrical Machine Analysis and Design · Vol. 3, Issue 2, 2025 · pp. 22–29 Read article
-
Solar Charkha Retrofit
Abstract: Hand operated charkha is used to make thread from cotton. It is sensitive work and involves great deal of care and effort to spin the charkha wheel manually during thread extrusion. Charkha operation causes physical strain and fatigue in long run. Abrupt spinning creates thread knots and breakage thus results poor quality and cotton wastage. Large number of people board on this khadi profession to make their meager earnings and …
Published in Trends in Machine design · Vol. 9, Issue 3, 2022 · pp. 23–28 Read article
-
Comparison of RSM and ANN Modeling Approaches in Predicting the Laser Phase Transformation Hardening Parameters on the Heat Input and Hardened-Bead Profile Quality of Unalloyed Titanium
Abstract: In the present work, laser transformation hardening (LTH) of unalloyed titanium, nearer to ASTM Grade 3 of chemical composition was investigated using CW 2kW, Nd: YAG laser. The laser process variables such as laser power, scanning speed, and focused position play a major role in deciding the laser hardened bead quality. Two methods, Response Surface Methodology (RSM) and Artificial Neural Network (ANN) were used to predict the heat input and …
Published in Journal of Materials & Metallurgical Engineering · Vol. 5, Issue 1, 2015 · pp. 36–59 Read article
-
Perturb and Observe Maximum Power Point Tracking Technique with PID Controller for a Wind Power System
Abstract: The wind power generation system has a significant growth worldwide over the past four decades. The wind power generation system has strong coupling and linear characteristics which makes it a complicated electromechanical system. The power control strategy has a higher impact on the overall performance as the wind power generation is operated at variable and random wind speed conditions. PID control is the most used control algorithm in industrial applications. …
Published in International Journal of Advanced Control and System Engineering · Vol. 1, Issue 1, 2023 · pp. 15–25 Read article
-
Analysis of Surface Roughness and Material Removal Rate in Engine Valve Turning Operation of Material SUH3
Abstract: The purpose of this paper is to present an experimental work attempting to optimize the influencingprocess parameters involved in dry machining of the exhaust engine valve of material martensiticstainless steel grade SUH3. Looking at available literature it is observed that a lot of work can be donein the field dry machining related to surface integrity but no work can be reported on investigationimplementation of dry machining in engine valve manufacturing …
Published in Journal of Automobile Engineering and Applications · Vol. 8, Issue 1, 2021 · pp. 17–22 Read article
-
Evaluation of Reliability in Five-Phase Induction Motor Operated at Low Speed by V/F Control Method using FPGA
Abstract: AbstractThis paper presents the study of performance and reliability evaluation of five-phase induction motor by finding various parameters in the induction motor. Induction motors have increased demand for low cost and size, simple construction, least maintenance, operational simplicity and brush-less construction with cage rotor. Industrial applications demand high efficiency, and reliable and long life-time electrical machines. The fault modes of induction machines are very complex; many researchers are plagued to …
Published in Journal of Power Electronics and Power Systems · Vol. 4, Issue 2, 2014 · pp. 56–61 Read article
-
Speed Estimation of High-Speed Hysteresis Motor Based on Extended Kalman Filter
Abstract: High-speed hysteresis motors are used in special industries such as medical centrifuges and gyroscopes. In spite of that, they are synchronous motors in some situations they may work in asynchronous speed. So, for reliable performance of hysteresis motor, closed loop control strategies are employed. On this way, speed/position of rotor must be known. Due to difficulty of using the speed sensors in high-speed hysteresis motor drives, employing the speed estimation …
Published in Journal of Power Electronics and Power Systems · Vol. 6, Issue 1, 2016 · pp. 34–44 Read article
-
A Study of Macrostructure and Wear Behavior of AL7075-B4C MMC Using DoE Method
Abstract: Metal matrix composites are advanced materials produced by combining two or more constituents. In that the major phase called matrix alloy and the other is, generally, ceramic reinforcement. AA7075- B4C Composites are popular in automotive, aerospace and defense fields because of their high strength-to-weight ratio, wear resistance, etc. Present work is focused on the study of wear behavior of Aluminum 7075 Alloy with B4C composites prepared by using Stir Casting …
Published in Trends in Mechanical Engineering & Technology · Vol. 9, Issue 2, 2019 · pp. 25–32 Read article
-
Parametric Study of Laser Drilling Process Using Multi Variable Regression Analysis
Abstract: The laser drilling process is an advanced manufacturing technique extensively employed for intricate and high-value components in aerospace, automotive, and electronics industries. Laser drilling technology offers opportunities to meet the contemporary demands of industries using a broad spectrum of engineering materials. However, this process encounters several engineering challenges such as thermal damage, dimensional inaccuracies, and the formation of a recast layer in the drilled components. This study focuses on examining …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1000–1015 Read article
-
Motorised Dual Side Shaping Machine with IoT Integration
Abstract: This work presents the design, fabrication and testing of a Motorised Dual Side Shaping Machine intended for small-scale workshops and educational laboratories, enhanced by an Internet of Things IoT based motor control system using the ESP32 microcontroller. The machine employs a 250 watt geared motor as the prime mover, transmitting power through a chain and sprocket mechanism to a 20 mm mild steel shaft supported on pedestal bearings (P204), where …
Published in Trends in Machine design · Vol. 13, Issue 2, 2026 · pp. 26–35 Read article