Search
40 articles for “travelling speed”
-
Combined Effect of Welding Speed and Tool Pin Profiles on Tensile properties of FSWAA6061-T6 Joint
Abstract: Friction stir welding is a solid state welding process for joining two similar and dissimilar materials, in which non-consumable tool with rotary motion along with transverse motion with intimate contact to weld coupon generates sound joint. In this study, tool rotation speed, tool travel speed and tool pin profile are taken to know their effect on mechanical properties of AA6061-T6. The main objective for this research is to evaluate the …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 4, Issue 1, 2017 · pp. 24–31 Read article
-
Short Circuit MAG/MIG Welding and Fast ROOT Modified Short arc Welding Process for Sheet Metals Welding with Diverse Air Gap
Abstract: The outcome of an analysis allocating with welding of sheet metals with diverse air gap using short circuit MAG welding process and Fast ROOT custom-made short arc welding methods have been presented. Welding turns were made below different conditions and through each run; the diverse process parameters were incessantly observed. It was found that fewer HAZ and maximum welding speed are reached under an exact welding condition with quick ROOT …
Published in Journal of Materials & Metallurgical Engineering · Vol. 6, Issue 1, 2016 · pp. 47–59 Read article
-
Application of flux cored arc welding (fcaw) without pre-heating for heavy structures in ship building fabrication & construction of heavy offshore structural steels
Abstract: In fusion welding processes, the reason often given to explain the need for preheating, controlling the inter pass temperature (in multi-pass welds), and post-weld heat treatment (PWHT) is to reduce the risk of residual stresses and it can be removed by heating weldment in the heat affected zone (HAZ). Cold cracking is a hydrogen embrittlement phenomenon, often referred to as hydrogen induced cracking or HAZ cracking. During the construction and …
Published in Journal of Construction Engineering, Technology & Management · Vol. 10, Issue 1, 2020 · pp. 20–28 Read article
-
Analysis of Friction Stir Welded Aluminum Alloys 2014 and 8011
Abstract: In this work we investigated friction stir welding of Aluminum Alloy 2014, Aluminum Alloy 8011. The major defects occurring while friction stir welding are tunnel effect, poor tensile strength, uneven material flow. The main causes for these defects are improper selection of welding parameters. The major welding parameters considered in Friction stir welding are spindle rotational speed (rpm), tool travel speed (mm/min) and tool angle (degree).In this work steps are …
Published in Journal of Materials & Metallurgical Engineering · Vol. 5, Issue 1, 2015 · pp. 12–17 Read article
-
A Method of Mesh Deformation for Flow Analysis Around Oscillating Bodies
Abstract: In general, high-speed rotating machines are subjected to complex phenomena due to various reasons, such as increased noise and strong vibration due to dynamic unbalance, which affect the dynamic motion of rotating machines and are necessarily a problem to overcome. Therefore, it is necessary to have a mathematical model to simulate it, and a strong tool to solve the constructed model. Using fluid-structure coupling techniques, which are currently a powerful …
Published in Journal of Experimental & Applied Mechanics · Vol. 16, Issue 2, 2025 · pp. 35–42 Read article
-
Evaluation on the Mechanical Strength of TIG Welded 6061Aluminium Alloy Joints
Abstract: Aluminum alloy Al-6061 is extensively used in aerospace, automotive, and marine industries due to its excellent mechanical properties, lightweight nature, and corrosion resistance. However, welding this alloy presents challenges such as porosity, hot cracking, and strength reduction in the heat-affected zone (HAZ). Tungsten Inert Gas (TIG) welding, known for its precision and quality, is commonly employed for joining Al-6061. This study investigates the tensile strength of TIG-welded butt joints of …
Published in Trends in Machine design · Vol. 13, Issue 1, 2026 · pp. 34–39 Read article
-
Application of Neural Network Analysis to Correlate the Properties of Plasma Spray Coating
Abstract: Thermal spray coatings are more often being demanding process at the recent stages of industrial design processes to become fundamental element of the engineering system. The aim of the present paper is to develop a model-based estimation and control for regulating the coating adhesion strength, by using neural network. This proposed model permits cost reduction by the possibility of adjusting the parameter of the process for each of the desired …
Published in Journal of Materials & Metallurgical Engineering · Vol. 2, Issue 1-3, 2012 · pp. 1–10 Read article
-
Drilling machine operations and characteristics, including benefits and drawbacks
Abstract: The drill press's capabilities vary depending on the machine's electronic motor, pillar diameter, spindle nose, travel, speed, and spindle speed. These are widely utilised in the automotive, printing, and engineering industries to improve the machine's consistency and tensile strength while quickly transitioning to resistive materials with high-quality results. Industries that require the mixing and grinding of solid and liquid material frequently use milling cum drilling machines.Drilling equipment is classified based …
Published in Trends in Mechanical Engineering & Technology · Vol. 12, Issue 2, 2022 · pp. 12–16 Read article
-
Analysis of hyperloop transportation system using electromagnetism
Abstract: In this paper, we consider the feature of (Hyperloop technology) revolutionary transportation technology. The new technology of transportation, which travel in Vacuum fully.A high-speed train that promises travel at twice the speed of commercial aircraft transport. A Hyperloop transportation system would be “an elevated, reduced-pressure tube that contains pressurized capsule driven with in the tube by a number of linear electric motor’’. This system can achieve an average speed of …
Published in Journal of Instrumentation Technology & Innovations · Vol. 11, Issue 2, 2021 · pp. 1–6 Read article
-
Simulation Study of Construction Work Zones – A Case Study
Abstract: Rapid infrastructure development paves way to widening and strengthening of highways. During this process, construction work zones are encountered. Speed in the construction work zones is a vital factor to be focused upon, especially on highways. If the speed is high, fatal accidents will occur in the work zone and if it is too low, it will contribute towards the delay, followed by increased queue lengths and thereby increased vehicle …
Published in Recent Trends in Civil Engineering & Technology · Vol. 2, Issue 1-3, 2012 · pp. 113–123 Read article
-
Utilization of Oobleck for A Speed Breaker
Abstract: AbstractOobleck is a non-Newtonian fluid made of corn starch and water, easily made and biodegradable. The aim of this research article is to evaluate the performance of Oobleck as a speed breaker and compare it with Conventional Speed Breaker and plastic speed breaker. It assumes a definitive job in actualizing speed limits, along these lines averting over speeding of vehicles. It extensively helps to the general street wellbeing objective through …
Published in Recent Trends in Fluid Mechanics · Vol. 6, Issue 3, 2019 · pp. 17–21 Read article
-
Ecomotion Cityglide Commuter E-Bike
Abstract: The transition from conventional gasoline motorcycles to electric bikes represents a pivotal step in addressing the increasing demand for sustainable transportation solutions in urban environments. This paper meticulously explores the multifaceted aspects of this transition, focusing on the technological advancements, design innovations, and societal implications associated with the adoption of electric bikes. Electric bikes, powered by Brushless DC (BLDC) motors and rechargeable battery packs, offer a suite of benefits over …
Published in International Journal of Mechanical Dynamics and Systems Analysis · Vol. 2, Issue 1, 2024 · pp. 43–49 Read article
-
Plastic Slatted Plate and Conveyor Belt
Abstract: This project is about the plastic slatted floor used for poultry farming. The findings of this study suggest that perforated plastic floors could be a good alternative to substitute wood shavings to raise broilers (male and female) since it was efficient from the perspective of environmental conditions and production rates, promoting a better quality environment and superior production rates. However, more research must be conducted to study the effects of …
Published in Trends in Machine design · Vol. 7, Issue 2, 2020 · pp. 10–13 Read article
-
Rough Terrain Robot (R-HEX)
Abstract: The RHex Robot, a power autonomous, untethered, compliant-legged hexapod robot. RHex is based on a Hexapod Robot. RHex has only six actuators one motor located at each hip achieving mechanical simplicity that promotes reliable and robust operation in real-world tasks. The legs rotate full circle, thereby preventing the common problem of toe stubbing in the protraction (swing) phase. An extensive suite of experimental results documents the robot’s significant “intrinsic mobility” …
Published in Current Trends in Information Technology · Vol. 10, Issue 2, 2020 · pp. 18–23 Read article
-
Speed Detection of Vehicles Using Ir Sensors
Abstract: The goal of this article is to detect automobiles travelling at excessive speeds on highway roads. Despite the highway's maximum speed restriction, numerous accidents occur as a result of over speeding. According to a recent study, current speed detection technology and methodologies are more expensive and can only identify one car at a time. Many various technologies are available to develop over speed detection systems, including as radar or laser …
Published in Current Trends in Signal Processing · Vol. 12, Issue 1, 2022 · pp. 11–14 Read article
-
Rail and Coil Gun Based Levitating Hybrid Train
Abstract: Hybrid train is a train which is a hybrid of the concept ideas of coil gun, rail gun, halback array, magnetic levitation etc. Theoretically this train could achieve the fastest Speed an object could reach respect to its mass. This train could surpass sound barrier and could even be made to go to speed exceeding mach 3. But due to travel safety a certain speed limit can be implemented in …
Published in Trends in Electrical Engineering Read article
-
Rail and Coil gun Based Levitating hybrid Train
Abstract: Hybrid train is a train which is a hybrid of the concept ideas of coil gun, rail gun, halback array, magnetic levitation etc. Theoretically this train could achieve the fastest Speed an object could reach respect to its mass. This train could surpass sound barrier and could even be made to go to speed exceeding mach 3. But due to travel safety a certain speed limit can be implemented in …
Published in Trends in Electrical Engineering · Vol. 11, Issue 2, 2021 · pp. 35–41 Read article
-
Driver Observation and Automatic Braking System Using Arduino
Abstract: Autonomous braking systems and driver observation are two important developments in car safety technology that are intended to reduce accidents brought on by tired drivers. An eye blink sensor has been incorporated in the device. The sensors recognize an eye blink automatically once the driver starts the engine. This gadget displays the sensor's output so that it may be compared to the Arduino. The eye blink sensor gets a signal …
Published in Journal of Microcontroller Engineering and Applications · Vol. 11, Issue 2, 2024 · pp. 28–33 Read article
-
Comprehensive Review on Brake Friction Materials
Abstract: Automobile manufacturers are currently dedicated to enhancing vehicle speeds for the purpose of saving travel time. However, achieving this objective necessitates the use of friction materials capable of handling high-speed braking. In this article, we will delve into the historical evolution of materials utilized for brake pads and drums. In the past, asbestos stood out as the most widely employed brake lining material due to its effectiveness. Unfortunately, its carcinogenic …
Published in Journal of Polymer & Composites · Vol. 11, Issue 8, 2023 · pp. 197–214 Read article
-
Analyzing the Influence of Soil-Structure Interaction on High-Speed Rail Embankments: A Plaxis 3D Simulation Study
Abstract: The introduction of high-speed rail (HSR) in India has seen an increase in travel demand and areduction in travel time. However, the stability and deformation characteristics of railwayembankments and soil structure interaction behavior under high-speed design requirements forIndian soil conditions need to be predicted using simplified 3-D finite element modelling. Theobjective of this research is to analyze the rigid ballast-less and flexible ballast-based high-speed railtrack embankments for various critical conditions …
Published in Trends in Transport Engineering and Applications · Vol. 10, Issue 1, 2023 · pp. 18–45 Read article