Search
6 articles for “aluminium-magnesium alloy matrix”
-
Characterization of Aluminum Metal-Matrix Composite with SiC and B4C Reinforcement with Different Weight Percentage
Abstract: Metal Matrix Composites (MMCs) have been prepared by compo casting method. The effect of matrix material on the wettability/compatibility of refinement with matrix is studied. Silicon and boron ceramic particles were used as reinforcement in aluminum matrices. The study of density, micro-hardness and the tensile strength has been done in order to characterize the same. It is found that Al-SiC MMC shows an increase in density with increasing weight percentage …
Published in Journal of Experimental & Applied Mechanics · Vol. 6, Issue 1, 2015 · pp. 1–6 Read article
-
A Novel Technique for Improved Recovery of Mg-Analysis of the Microstructure and Physical Properties
Abstract: Aluminium-Magnesium alloys are used widely in industrial applications as well as for the preparation of metal matrix composite because of their low density and high specific strength. Magnesium has a low boiling point and the recovery of magnesium is poor when it is added in pure form particularly as cheaply available turnings to the liquid metal. Magnesium is added to aluminium for increasing its wettability and thus helping in uniformly …
Published in Journal of Materials & Metallurgical Engineering · Vol. 3, Issue 1, 2013 · pp. 1–7 Read article
-
Evaluation of Mechanical Behaviour of Tungsten Carbide and Magnesium Reinforced Aluminium Matrix Composites
Abstract: With industries like automotive and aerospace also being more inclined on the lightweight material and strength that is much substantial, the aluminium-based metal matrix composite has become a major focus of interest. This paper examines the influence of addition of tungsten carbide (WC) and magnesium (Mg) particles on the mechanical characteristics of Al6063 aluminium alloy. The crucible casting technique was made in two composite compositions 2.5 percent and 5 percent …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 1–8 Read article
-
Experimental and Numerical Investigation of Corrosion-Induced Failures in Copper-Tin Alloy (Cu-Sn) and Aluminum-Magnesium Alloy (Al-Mg) Connectors: A Stress–Corrosion Coupling Analysis
Abstract: The utilization of an integrated experimental and finite element modelling (FEM) methodology, this study investigates the degradation and failure mechanisms in polymer composite electrical connectors exposed to aggressive environmental conditions. Epoxy- and polyamide-based composites, reinforced with carbon and glass fibers, were subjected to accelerated salt spray and humidity–temperature cycles to simulate prolonged outdoor exposure. Electrochemical and environmental aging experiments revealed that chloride ions and moisture ingress were responsible for matrix …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 366–379 Read article
-
Processing and Properties of In situ Synthesized Reinforcements in Molten Magnesium
Abstract: In situ synthesized reinforcements for magnesium composites are an attractive area of research especially due to the inherent advantages of the process. Various reinforcements such as intermetallics and ceramics have proved their effectiveness in magnesium by imparting higher mechanical and tribological properties to the metal matrix. Fabrication of reinforcements in molten magnesium matrix is a very critical area owing to large scale production prospective and ease of implementation. This paper …
Published in Journal of Materials & Metallurgical Engineering · Vol. 3, Issue 1, 2013 · pp. 25–33 Read article
-
Wear Characteristics of Aluminium-Graphite Composites Produced by Stir Casting Technique
Abstract: Metal matrix composites (MMCs) are finding more applications due to their significantly improved properties such as high specific strength, high specific modulus, good damping capacity and good wear resistance compared to unreinforced alloys. In recent years, there has been an increasing interest in composites containing low density and low cost reinforcements. Graphite is one of the most suitable and low density reinforcement available for making light-weight and wear resistant parts …
Published in Journal of Materials & Metallurgical Engineering · Vol. 4, Issue 3, 2014 · pp. 13–20 Read article