Search
7 articles for “Wood Sawdust”
-
Optimization of Sulphuric Acid Hydrolysis Process for Fermentable Sugars from Lignocellulosic Content of Wood Sawdust for Production of Cellulosic Ethanol
Abstract: The aim of this study was to investigate the optimization of acid hydrolysis process for fermentable sugars from the lignocellulosic content of wood sawdust for cellulosic ethanol production. In this study, four process parameters were investigated; acid concentration (3-7%), solid fraction (8-12ml/gm), temperature (100-120oC) and time (90-150minutes). The total reducing sugar content of hydrolyzed solutions was analyzed using Phenol-Sulfuric Acid method. The result of the statically analysis 2mm particle size …
Published in Emerging Trends in Chemical Engineering · Vol. 7, Issue 1, 2020 · pp. 10–18 Read article
-
Production of Cellulosic Ethanol from Wood Sawdust by Sulphuric acid Hydrolysis
Abstract: In this study, production of cellulosic ethanol from wood sawdust was investigated. Four experimental parameters were investigated during the hydrolysis and ethanol production. These are particle size (1–3 mm), acid concentration (3–7%), temperature (90–110°C), and time(120–240 min). The total reduced sugar content and ethanol yield was determined. Response surface methodology (RSM) employing the central composite design (CCD) was used to optimize the total reduced sugar and ethanol yield. Cite this …
Published in Journal of Petroleum Engineering & Technology · Vol. 7, Issue 3, 2017 · pp. 30–35 Read article
-
Drying and Particle Size Characteristics of Danta (Nesogordonia papavereria) and Hard Cross (Vitex doniana) Wood Sawdusts at Different Temperatures
Abstract: The drying and particle size characterization of Danta (Nesogordonia papavereria) and Hard Cross (Vitex doniana) hardwood sawdusts were investigated at temperatures 80 ºC, 90 ºC and 105 . The experimental drying data were modeled using eighteen existing drying models. The results showed that the modified Henderson and Pabis model offered the best fit to the drying curves of Danta and Hard Cross sawdusts. The experimental data obtained from the particle …
Published in Journal of Alternate Energy Sources & Technologies · Vol. 7, Issue 1, 2016 · pp. 30–38 Read article
-
Evaluation of Mechanical Properties of Terminalia Chebula and Teak Wood Sawdust Reinforced Polymer Hybrid Composites
Abstract: This study examines the mechanical characteristics of polymer hybrid composites augmented with sawdust from teak wood and Terminalia chebula (Kadukkai). To examine their effects on mechanical performance, the composites were made with different percentages of biofiller (10%, 20%, 30%, 40%, and 50%) while keeping the proportions of the two reinforcements same. Tensile, flexural, and impact tests were performed to assess their strength properties. The findings showed that flexural strength varied …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 469–476 Read article
-
Synthesis and Characterization of Sustainable, Low-Cost, Biomass-Derived Carbon Films from Hevea Brasiliensis (Rubber) Wood for Environmentally Friendly Gas Sensors with Enhanced Selectivity and Sensitivity to Polar Vapors and Hazardous Gases
Abstract: Hevea brasiliensis (rubber) wood sawdust was utilized to fabricate carbon gas sensors for detecting 1000 ppm of ethanol, methanol, acetone, carbon dioxide, and ammonia gases. The carbon particles were prepared by phosphoric acid impregnation followed by thermal activation and then fabricated into films on conductive and non-conductive substrates using the doctor blade method. X-ray diffraction (XRD) analysis revealed distinct graphitic features with peaks at the (002) and (100) planes, indicating …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 12, Issue 1, 2025 · pp. 22–36 Read article
-
Production of Polymer Composite using Thermoplastics, Sharp Sand and Sawdust: Mix Techniques
Abstract: This research work focuses on producing a polymer composite using a thermoplastic. PET is nonbiodegradable and contribute majorly to water and land pollution in this research work an attempt has been made to utilize PET waste plastic in manufacturing fibre-reinforced polymer composite by combining sawdust which is another waste product from woodwork operations and sand, a major component in construction, whose use is greatly threatening the ecosystem. The fibre-reinforced polymers …
Published in Emerging Trends in Chemical Engineering · Vol. 9, Issue 3, 2022 · pp. 21–29 Read article
-
Characterization and Fabrication of Particle Board from Banana Fiber and Sawdust as A Hybrid Composite
Abstract: The current global landscape emphasizes the search for eco-friendly and regenerative materials. Utilizing environmentally available fibers in conjunction with polymeric resins through efficient manufacturing processes offers a cost-effective solution with high-quality standards. Polymer matrix composites with fiber reinforcements possess several advantages, including low production costs, ease of fabrication, and improved material properties, making them applicable in a wide range of industrial contexts. This paper emphasizes the creation of Particle boards …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 192–200 Read article