Search
14 articles for “Transient Thermal analysis.”
-
FE Analysis and Experimental Validation of Residual Stresses in Arc Welding
Abstract: This paper presents finite element analysis (FEA) of residual stresses developed in arc welded butt joints. Residual stresses attributed to welding pose significant problems in the accurate fabrication of structures because these stresses heavily induce brittle fracturing and degrade the buckling strength of welded structures. Therefore, estimating the magnitude and distribution of welding residual stresses and characterizing the effects of certain welding conditions on the residual stresses are deemed necessary.Keywords: …
Published in Journal of Experimental & Applied Mechanics · Vol. 6, Issue 1, 2015 · pp. 7–18 Read article
-
Quasi-Static Thermal Stress Analysis in a Thin Circular Cylinder Due To Internal Heat Generation Under Transient Temperature Conditions
Abstract: This paper is concerned with inverse quasi-static thermal stress analysis in a thin circular cylinder due to internal heat generation under transient temperature conditions. The internal heat generation is modeled as a cylindrical surface heat source located in the annular region along the axial length of the cylinder. This source is placed concentrically inside the cylinder and begins releasing heat spontaneously at a specific point in time. The thin circular …
Published in Recent Trends in Fluid Mechanics · Vol. 12, Issue 2, 2025 · pp. 17–28 Read article
-
Thermal Analysis of Casting using ANSYS: A Review
Abstract: The major requirement of any foundry is to provide the high quality casting products. Since the quality is depended upon thermal stress and solidification of the casting, a thermal analysis is a key area to work on. Heat transfer coefficient is the vital element of any thermal analysis. Mould and the casting interface is the most critical area that gets affected during the solidification. Heat transfer ratio at the inter …
Published in Journal of Production Research & Management · Vol. 6, Issue 1, 2016 · pp. 19–27 Read article
-
SIMULATION OF THE PERFORMANCE OF PV/T (PV-PCM) SYSTEMS IN TRANSIENT STATE
Abstract: The paper describes the analysis of the thermal performance of a PCM unit attached to a PV panel configuring a PV/T system. Thermal performance has been analyzed from the transient process point of view considering the temperature evolution of the PCM with time dependent on ambient temperature and solar radiation. A specific algorithm for determining the time evolution of the PCM temperature has been developed. The model uses the DERIVE …
Published in Journal of Thermal Engineering and Applications · Vol. 10, Issue 1, 2023 · pp. 1–13 Read article
-
Challenges In Sodium Cooled Fast Reactor Thermal Hydraulics
Abstract: Heat Transfer and Fluid flow phenomena (referred as Thermal Hydraulics) play a significant role in the safe and economical design of fast breeder reactors (FBR). The sodium cooled fast reactors have a very complex flow and temperature profile within the pool or the test vessel. The high temperature operating conditions (~540 deg.C) also impose stringent requirements on the thermal design of the components. The basic approach of thermal hydraulic design …
Published in Journal of Nuclear Engineering & Technology · Vol. 12, Issue 2, 2022 · pp. 33–47 Read article
-
Transient analysis of Earth Air Heat Exchanger using CFD for Summer Season
Abstract: Energy accumulation in the soil may be used with Earth-Air Tunnel Heat Exchanger (EATHE), which has single tube or groups of tube buried in the ground (soil). In a country like India, there exist big gap in demand and supply of electricity and compels to look for alternative. A thermal model was developed to analyze the thermal energy accumulated in soil/ground for the purpose of room heating and cooling of …
Published in Journal of Thermal Engineering and Applications · Vol. 1, Issue 2, 2014 · pp. 7–16 Read article
-
Design and Thermal Analysis of Fins for Air Cooled Engine by Varying its Geometry
Abstract: An air-cooled motorcycle engine releases heat to the atmosphere through the mode of convection to facilitate this, fins are provided on the outer surface of the cylinder. The cooling fins allow the wind to move the heat away from the engine. The heat transfer rate depends upon the velocity of the vehicle, fin geometry and the ambient temperature. Low rate of heat transfer through fins is the main problem of …
Published in Trends in Machine design · Vol. 5, Issue 3, 2018 · pp. 37–53 Read article
-
Finite Element Analysis of Steam Turbine Components for Real Life Assessment Studies of 210 MW Steam Turbine
Abstract: The turbine rotor or steam turbine rotor is subjected to temperature variations in short periods of time due to the start and stop cycles of the turbine. This causes sudden changes in the temperature with transient thermal stresses being induced into the turbine rotor. The transient effect is due to the changes in the material properties like density, specific heat and Young’s modulus. The estimate of thermal stresses induced in …
Published in Trends in Mechanical Engineering & Technology · Vol. 2, Issue 2, 2012 · pp. 6–16 Read article
-
Inverse Heat Transfer Analysis Applied to Heat Treatment Process
Abstract: Direct measurement of heat flux at the surface of a surface subjected to extreme heat using conventional or traditional methods is an inexpedient task; but it can be estimated by an inverse analysis utilizing transient temperature recordings taken at specific location beneath the heated surface. The problem on Inverse Heat Transfer (IHT) depends upon the heat flux and various temperature measurements for the approximation of variable quantities appearing in the …
Published in Journal of Refrigeration, Air conditioning, Heating and ventilation · Vol. 6, Issue 1, 2019 · pp. 14–19 Read article
-
Defining Regression Polynomials with Process Similarity Criteria
Abstract: Highly accurate monitoring and prediction is essential in detecting abnormality events and forecasting demands in supply chains. This investigation provides a computational procedure for defining polynomials that satisfy similarity criteria in the monitoring process for a polynomial of any degree. It provides an example of using algorithms to predict transient thermal processes in electronic devices. The second-degree polynomial defined with this algorithm is compared with a polynomial defined using a …
Published in Research & Reviews: Discrete Mathematical Structures · Vol. 10, Issue 2, 2023 · pp. 13–20 Read article
-
Review of Subsea Pipeline for Minimizing Thermal and Pressure Expansion
Abstract: As the offshore oil and gas fields have been exploited in deeper water, subsea pipelines are required to operate at high temperatures and pressures. It causes subsea pipelines to be more subject to movements both in lateral and axial directions due to the loads produced by high temperatures and pressures. Some high temperature pipelines have experienced the cumulative axial displacement of an overall pipeline length over a number of start-up/shut-in …
Published in Journal of Petroleum Engineering & Technology · Vol. 4, Issue 1, 2014 · pp. 10–22 Read article
-
THEORETICAL ANALYSIS OF ADVANCED PARABOLIC RECEIVER FOR DIRECT STEAM GENERATION
Abstract: Solar thermal power generation using water as a Heat Transfer Fluid (HTF) has gained interest recently, due to its ability to generate steam directly from the receiver tube. In this paper, a new theoretical model of receiver called Concentric Parabolic Trough Receiver (C-PTR) for direct steam generation is presented. The proposed model consists of Phase change material (PCM) sandwiched between two concentric cylindrical tubes. Binary Solar Salt commercially known as …
Published in Journal of Refrigeration, Air conditioning, Heating and ventilation · Vol. 2, Issue 1, 2015 Read article
-
Numerical Model for Water Hammer in Homogeneous Equilibrium Two Phase Fluid
Abstract: Generally, water hammer can occur in any thermal-hydraulic systems. Rapid closing or opening of a valve causes pressure transients due to the sudden transformation of kinetic energy into the potential energy. The resulting high pressure surge upstream of the valve leads to the temporary increase in pressure. If the increased pressure surpasses the safety margin for the pipe, it can lead to failure of the pipeline. A mathematical model is …
Published in Journal of Nuclear Engineering & Technology · Vol. 4, Issue 3, 2014 · pp. 29–43 Read article
-
Development and Analysis of Novel Silver Ion-Conducting Glass-Polymer Electrolytes
Abstract: The development of efficient and stable solid electrolytes is crucial for advancing energy storage technologies such as solid-state batteries and electrochemical devices. In this study, a novel series of silver ion-conducting glass–polymer electrolytes (GPEs) based on the composition (1–x) PEO: x[0.75AgI:0.25(Ag₂O:WO₃)] with x ranging up to 50 wt.% was synthesized and thoroughly analyzed. Unlike conventional techniques such as solution casting or sol–gel methods, these GPEs were fabricated using an innovative …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 600–605 Read article