Search
62 articles for “Fatigue test”
-
Fatigue Test on Cost Effective Aluminium Metal Matrix Composite Prepared from Discarded Toner Powder and Coconut shell Ash Particles
Abstract: AbstractAs there is an increasing demand for low cost reinforced composite materials in various industrial applications, in this work Aluminium Metal Matrix Composite was prepared by reinforcing cost effective reinforcements like discarded tonner powder particles and coconut shell ash. Aluminium 2024 was taken as the base matrix for preparing the composite as it is widely used in automobile industry. The samples taken for the investigation were prepared by two step …
Published in Journal of Thin Films, Coating Science Technology & Application · Vol. 5, Issue 3, 2018 · pp. 15–20 Read article
-
Effects of loading rates on durability life of a part for random loads
Abstract: In the current scenario of fierce competition, manufacturers are under tremendous pressure to launch defect free products at the earliest. Cutting down time at every stage of product development is the need of the hour and testing is no exception. Testing and validation in the automotive domain is of immense importance as any small failure can also lead to catastrophic consequences. Continuous emphasis is in place to accelerate the tests …
Published in Journal of Automobile Engineering and Applications · Vol. 5, Issue 3, 2018 · pp. 1–10 Read article
-
Design and Development of Experimental Test Rig for Fatigue Life Estimation of Freewheel One-Way Clutch Used in Switchgear Applications at High Overrunning Speeds
Abstract: Freewheel one-way clutch (OWC) is a critical component used in industrial circuit breakers/switchgear to facilitate quick disengagement of the drive when an electrical circuit trips under overcurrent. The clutch acts as a safety device to endure high overrunning speeds and allows the drive shaft to rotate at normal operating speeds during each tripping cycle. The trip mechanism utilizes the stored potential energy of the helical compression spring, which is the …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 289–299 Read article
-
Investigating Flexural Behavior in Cyclic Loading of Fly Ash-Based Green Concrete
Abstract: The construction industry is increasingly embracing sustainable materials, and geopolymer concrete (GPC) has emerged as a promising eco-friendly alternative to Ordinary Portland Cement (OPC). Derived from industrial by-products such as fly ash, GPC offers significant environmental advantages by reducing greenhouse gas emissions associated with conventional cement production. This study explores the monotonic and cyclic performance of fly ash-based GPC, with a focus on its mechanical and structural behavior. Key properties, …
Published in Journal of Structural Engineering and Management · Vol. 12, Issue 1, 2025 · pp. 1–5 Read article
-
Fatigue Study of Friction Stir Welded and TIG Welded AA 6061 Alloy Similar Joints
Abstract: In this study, Al-Mg-Si alloy plates in 4 mm thickness that are particularly used for aerospace and automotive industries were welded using Tungsten Inert Gas (TIG) welding and Friction Stir Welding (FSW) methods as similar joints with one side pass with parameters of varying tool rotation, weld speed and 2.3 degree tool tilt angle. Tensile tests results showed high yield stress values for FSW joints. Micro Vickers hardness test gave …
Published in Trends in Mechanical Engineering & Technology · Vol. 10, Issue 1, 2020 · pp. 12–21 Read article
-
Investigating The Influence of Sic Reinforcement on The Mechanical and Tribological Properties of PA12 Polymer Composites in SLS
Abstract: The study investigates the mechanical and tribological performance of neat PA12 polymer and SiC-reinforced PA12 polymer composites made via Selective Laser Sintering (SLS). To evaluate just how reinforcement has influence upon overall performance, we incorporated into the PA12 polymer matrix a constant amount of 5 wt.% of Silicon Carbide (SiC). Mechanical testing focused on both tensile and fatigue behavior and testers conducted it with a Servo-Hydraulic Multipurpose High-Capacity Fatigue Test …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 541–554 Read article
-
Condition Monitoring of a Round Bar with a Defect Using Vibration Analysis
Abstract: As an energy-saving and high-efficient stress relieving process, vibratory stress relief [VSR] influence of on fatigue life is still explicit and needs further investigation. Standard specimens are manufactured to study the VSR effects on 2014 T6 aluminum alloy fatigue behavior. Dynamic stresses generated during vibration are measured by strain gauge and the residual stresses with and without VSR are compared to validate the stress relieving effects. Eventually, fatigue tests are …
Published in Trends in Machine design · Vol. 6, Issue 2, 2019 · pp. 5–7 Read article
-
A Comprehensive Study of Radial Load Fluctuation on Alloy Wheels for Electric Vehicles
Abstract: Electric Vehicle’s alloy wheels are designed to allow for better heat dissipation. Manufacturers carry out many tests of a wheel to be sure, that the wheel will fit for safety reason as also their comfortability level is even bigger. Therefore, a specific design was selected for which the simulations of alloy wheel were performed under real loading conditions. The main objective of this research is to analyze the effects of …
Published in International Journal of Mechanical Dynamics and Systems Analysis · Vol. 2, Issue 2, 2024 · pp. 47–56 Read article
-
Composite Fabrication by Stir-Cast for Al C355.0 With Particulates Hematite Reinforcements at Different Weight Percentages in Copper Chills with and Without Water Circulation for Mechanical and Fatigue Performance
Abstract: This study investigates the fabrication of aluminum matrix composites using the stir casting method to analyze the mechanical characterization and fatigue behavior of Al C355.0 composites reinforced with varying weight percentages of hematite particulates. The hematite content was systematically adjusted from 0 wt. % to 12 wt. % in 3 wt. % increments, with the presence of constituent elements confirmed through Energy Dispersive Spectroscopy (EDS). The incorporation of hematite reinforcement …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 324–336 Read article
-
Data-Driven Life Prediction of Fiber-Reinforced Polymer Composites Using IoT Sensing and Machine Learning Algorithms
Abstract: The accurate prediction of fatigue life in fiber-reinforced polymer (FRP) composites remains a major challenge due to their nonlinear, multi-mechanism degradation behavior under variable loading conditions. This study presents a data-driven framework, H-LiProNet, which combines real-time IoT sensing with hybrid machine learning to estimate remaining useful life (RUL) in FRP composites. The proposed system integrates embedded Fiber Bragg Grating (FBG) and acoustic emission (AE) sensors to capture strain and damage …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 116–130 Read article
-
Flexural Behavior of Warm Mix Asphalt Concrete
Abstract: Research work on implementation of Warm Mix Asphalt (WMA) for roadway paving has been undertaken by many researchers due to its beneficial impact on the environment and reduction in the fuel consumption. In this investigation, two WMA mixtures have been prepared in the laboratory using medium curing cutback (MC-30) and Cationic emulsion. Hot mix asphalt (HMA ) mixture was also prepared for comparison. Beam specimens of (380 mm) in length, …
Published in Trends in Transport Engineering and Applications · Vol. 5, Issue 2, 2018 · pp. 10–20 Read article
-
Influence of Constant Micro Strain Levels on the Strength Properties of the Asphalt Concrete mixture
Abstract: Asphalt concrete mixture is designed to resist the deformation and vehicular traffic loading throughout its service life. However, when the asphalt concrete pavement practices over loading within the service life period, it exhibits cracking and rutting. In the present investigation, an attempt has been taken to understand the strength performance of asphalt concrete when practicing variable levels of constant stresses. Asphalt concrete mixture was prepared at optimum asphalt cement requirement …
Published in Trends in Transport Engineering and Applications · Vol. 10, Issue 3, 2023 · pp. 29–35 Read article
-
Detecting the Failure Stages in Asphalt Concrete Through the Fatigue Life
Abstract: The signs of failure initiation in asphalt concrete through its service life may appear as cracking, rutting, or other types of distress after practicing dynamic stresses from vehicular loading. This work is concerned with detecting the failure initiation in asphalt concrete in the laboratory, and the role of binder content and constant strain level through a comprehensive testing program. Asphalt concrete mixtures were formulated with the optimal binder content, as …
Published in Trends in Transport Engineering and Applications · Vol. 11, Issue 1, 2024 · pp. 21–27 Read article
-
Contributing factors in the initiation of failure of asphalt concrete
Abstract: As long as the asphalt concrete pavement is under service, signs of failure usually initiate and the distress types start showing throughout the service life. The asphalt concrete pavement practices repeated tensile and shear stresses through the vehicular loading. In the present study, the contributing factors in the initiation of failure under repeated flexural stresses have been detected. Slab samples of Asphalt concrete have been prepared at the laboratory by …
Published in Trends in Transport Engineering and Applications · Vol. 10, Issue 1, 2023 · pp. 55–61 Read article
-
Effect of Chemically Treated Plant Cellulose on Mechanical, Fatigue and Fracture Toughness Behaviour of Polyester Composite
Abstract: In this research study, the effect of chemically treated plant cellulose on the mechanical, fatigue, and fracture toughness behaviour of polyester composites was investigated. Ramie plant cellulose fibers were used as the reinforcing material, and polyester resin was used as the matrix material. Three different chemical treatment processes, namely alkalization, acetylation, and etherification, were used to adapt the superficial chemistry of the fibers and advance their compatibility with the polyester …
Published in Journal of Polymer & Composites · Vol. 11, Issue 3, 2023 · pp. 21–29 Read article
-
Role of Fatigue and Creep in Structural Damage: A Comprehensive Review
Abstract: Fatigue and creep are two critical degradation mechanisms that significantly influence the structural integrity and longevity of engineering materials. These phenomena arise due to different loading and environmental conditions but often coexist in various industrial applications, leading to severe material degradation over time. Fatigue primarily results from cyclic loading, where repeated stress variations induce microstructural damage and crack initiation, ultimately causing catastrophic failure. Conversely, creep occurs under sustained stress at …
Published in International Journal of Fracture Mechanics and Damage Science · Vol. 3, Issue 1, 2025 · pp. 22–26 Read article
-
Assess the Effectiveness of Progressive Muscle Relaxation Therapy on Health Status among Blood Cancer Patients Receiving Cancer Treating Medications in Selected Hospital
Abstract: Introduction: Cancer can be regarded as a group of diseases characterized by an i) abnormal growth of cells ii) ability to invade adjacent tissues and even distant organs, and iii) the eventual death of the affected patient if the tumour has progressed beyond that stage when it can be successfully removed. Cancer can occur at any site or tissue of the body and may involve any type of cells. Cancer …
Published in Research and Reviews: Journal of Oncology and Hematology · Vol. 10, Issue 2, 2021 · pp. 1–20 Read article
-
A Study to Assess the Add-on Impact of Ayurvedic Management along with Ongoing Conventional Treatment of Diabetes Mellitus: A Randomized Clinical Trial
Abstract: Diabetes mellitus is a metabolic disorder of multiple etiologies characterized by chronic hyperglycemia with disbalance of carbohydrate, fat and protein metabolism resulting from defects in insulin secretion, action, or both. Diabetes affects millions and thus is a major public health disease among with adults aged 30+. Available treatment although helps but many develop other side effects to complicate the issue. Ayurveda offers options to manage diabetes without complications. Present study …
Published in Research and Reviews : A Journal of Ayurvedic Science, Yoga and Naturopathy · Vol. 8, Issue 1, 2021 · pp. 15–22 Read article
-
Critical Review of Fatigue Properties of Friction Stir Welds of Aluminum Alloys
Abstract: Friction Stir Welding (FSW) is a solid state welding technique being developed for various metals and alloys. It allows joining of high strength aluminum alloys which is generally difficult to weld with conventional welding techniques. This joining technique is energy efficient, environment friendly, and versatile. FSW is considered to be the most significant development in metal joining in a decade. It is expected to have various weld properties to meet …
Published in Journal of Materials & Metallurgical Engineering · Vol. 4, Issue 1, 2014 · pp. 1–6 Read article
-
New Design Formulae for Safety and Precision in the Fatigue Engineering of Mechanical Components and Structures
Abstract: This paper introduces two new formulae, termed the Nori Fatigue Formulae, for determining the maximum allowable fatigue stress in mechanical components and structures with significant stress concentrations. These formulae will eliminate the usage of code-sensitive safety factors along with other factored values from the entire mechanical design engineering work, ranging from a safety pin to spacecraft. The first formula gives the maximum allowable fatigue stress in tension, and the second …
Published in Trends in Mechanical Engineering & Technology · Vol. 16, Issue 1, 2026 · pp. 6–24 Read article