Search
34 articles for “Drilling”
-
Analysing the Deep Hole Drilling Characteristics of AISI 316 Alloy Using Peck Drilling Approach
Abstract: This study aims at the deep hole drilling characteristics of AISI 316 alloy utilizing the Peck drilling procedure. It is well-established that hole is the most prevalent machining process, requiring precise techniques to achieve optimal cutting conditions. AISI 316 has high corrosion resistance and mechanical features. It is widely utilized in the aerospace, vehicle, aircraft, and other industries. Due to its high modulus of elasticity, reactivity at high cutting speeds, …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 14–28 Read article
-
A Ponder & Sedulousness Of Legion Shale Stabilizing Materials In Aqueous Based Drilling Fluid During The Process Of Borehole Strengthening
Abstract: Drilling fluid used while drilling the layers of shale will have the potential of reacting with water which tends to increase stickiness, induce swelling and promote sloughing of the borehole. This results in the reduction of drilling fluid circulation, increased mud loss, increase in torque and drag, reduction in lubricity. This will ultimately result in the increase of Non-Productive Time (NPT) during drilling which in turn increases Capital Expenditure (CAPEX) …
Published in International Journal of Pollution: Prevention & Control · Vol. 1, Issue 2, 2023 · pp. 35–40 Read article
-
Multi-Objective Optimization of Carbon-Glass Fiber Polymer Drilling Process Based on Fuzzy Grey Entropy Weighing Method
Abstract: In recent years, the machining characteristics of hybrid fiber polymer composites have garnered significant research attention due to their growing industrial applications. This study specifically focuses on the drilling of hybrid carbon-glass fiber reinforced (CGFR) epoxy composites, fabricated using the hand layup technique. The key machining characteristics evaluated in this drilling process include surface roughness and circularity error. The influence of critical drilling process parameters, such as spindle speed, drill …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 100–112 Read article
-
Effect of Drilling Process Parameters on Surface Roughness of LM6/B4C/Fly Ash Hybrid Composites
Abstract: This research seeks to assess the effect of process variables such as feed rate (FR), spindle speed (SS), drill material (DM) and reinforcement (R%) on surface roughness (SR) when drilling LM6/B4C/Fly ash hybrid composites. The stir casting process was used to fabricate the LM6/B4C/Flyash hybrid composites utilizing LM6 aluminum alloy as the matrix material and B4C/Fly ash as strengthening materials. Experiments were carried out using an L18 orthogonal array (OA) …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 898–906 Read article
-
The Strength of Dry, Fresh and Decomposed Raffia Palm Trunk in the Bioremediation of Oil-based Drill Cutting
Abstract: In this research, the impact of dry drill cuttings and compost tea on the environment's ability to degrade oil-based drill cutting contamination is investigated. The experiment was conducted in the research center located at the workshop of Agricultural and Environmental Engineering Department, Rivers State University, Port Harcourt. Oil-based drill cutting samples were placed in bulk in eleven reactors (T1, T2, T3-T11) with four replications. The original drill cuttings' physiochemical characteristics …
Published in Journal of Modern Chemistry & Chemical Technology · Vol. 15, Issue 3, 2024 · pp. 26–33 Read article
-
Drilling Fluid Characterization (Filtration Test)
Abstract: This report explores the formulation and testing of a water-based drilling mud used in drilling operations, where fluid circulates through the drillstring and returns to the surface. The study mixes 315 ml of water with 35 ml of corn oil to create the drilling mud and investigates the role of barite in increasing mud density to maintain a hydrostatic pressure capable of managing formation pressure. The findings reveal that increasing …
Published in Journal of Petroleum Engineering & Technology · Vol. 14, Issue 2, 2024 · pp. 17–26 Read article
-
Kick Tolerance Modeling in Well Design and Drilling: A Comprehensive Technical Review
Abstract: Kick and blowout events in drilling operations can lead to significant losses of equipment, and in some cases, human lives. Oil and gas companies, along with oilfield service providers involved in drilling operations, face severe penalties and sanctions following such incidents. Research has demonstrated that incorporating kick tolerance models during the well planning and drilling stages can mitigate the risk of blowouts during secondary well control operations. This study reviews …
Published in Journal of Petroleum Engineering & Technology · Vol. 15, Issue 3, 2025 · pp. 33–58 Read article
-
Effect of machining parameters on the tool wear in drilling of 3D PF C/C composite
Abstract: Carbon–carbon (C/C) composites are broadly used in aerospace, defence, shipbuilding, chemical, and nuclear industries owing to their high strength-to-weight and stiffness-to-weight ratios. However, they are brittle, anisotropic and non-homogeneous in nature, making them difficult to machine. Incorrect machining parameters can cause defects such as burrs, delamination, and fibre bundles pullout. This paper aims to study the hole surface and tool wear during drilling of 3D pierced fabric (PF) carbon-carbon (C/C) …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 · pp. 269–281 Read article
-
Managed Pressure Drilling for Improved Well Control: A Cross-Case Comparative Study (2015–2025)
Abstract: Managed Pressure Drilling (MPD) has matured over the past decade from a specialist technique applied to challenging wells into a mainstream drilling capability spanning ultra-HPHT exploration, deepwater development, unconventional tight-gas multi-well campaigns, and naturally fractured sour-gas reservoirs. Despite this maturation, the operational question of which MPD variant should be applied to a given well has been addressed in the literature case-by-case rather than through structured comparative synthesis. This paper presents …
Published in Journal of Petroleum Engineering & Technology · Vol. 16, Issue 2, 2026 · pp. 07–12 Read article
-
Drilling Parameters Optimization in LM6/B4C/Fly ash Hybrid Composites by Taguchi Technique
Abstract: Aluminium matrix composites (AMCs) are challenging to machine due to its abrasive characteristics. Because of the broad adoption of MMCs, it is vital to create sufficient equipment to facilitate efficient manufacturing. The current study utilizes signal-to-noise ratio (S/N) analysis to determine the ideal machining parameters for drilling AMC’s. The goal with this study is to investigate the effect of feed rate (FR), drill type (D), speed (SS), reinforcing material R …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 890–897 Read article
-
Parametric Study of Laser Drilling Process Using Multi Variable Regression Analysis
Abstract: The laser drilling process is an advanced manufacturing technique extensively employed for intricate and high-value components in aerospace, automotive, and electronics industries. Laser drilling technology offers opportunities to meet the contemporary demands of industries using a broad spectrum of engineering materials. However, this process encounters several engineering challenges such as thermal damage, dimensional inaccuracies, and the formation of a recast layer in the drilled components. This study focuses on examining …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1000–1015 Read article
-
The Influence of Fresh Raffia Palm Trunk on the Bioremediation of Oil-Based Drill
Abstract: This study determines the effect of fresh raffia palm for biodegradation of oil-based drill cuttings bioremediation. The experiment was conducted at the rivers institute of Agricultural research and training (RIART) located at the Rivers State University, Port Harcourt. Samples of oil-based drill cuttings were bulked in eleven reactors with four replications (T1, T2, T3-T11). The physiochemical properties of the initial drill cuttings were analyzed. Also, the physiochemical properties of the …
Published in International Journal of Pollution: Prevention & Control · Vol. 1, Issue 2, 2023 · pp. 41–48 Read article
-
Optimization of Process Parameters for AISI 304 Using Micro-EDM Drilling Process Through Response Surface Method
Abstract: The increasing demand for micro-parts in high-tech products, such as micro-electromechanical systems (MEMS) applications and micro-electronic devices, has driven significant advancements in micromachining technologies. Among the various micromachining processes, the fabrication of accurate microholes and pins is critical for the performance and reliability of miniature components. Micro-hole drilling plays a vital role by enabling the production of deep holes with excellent straightness, roundness, and surface quality. It is widely used …
Published in International Journal of Manufacturing and Production Engineering · Vol. 3, Issue 1, 2025 · pp. 37–47 Read article
-
Flexural Strength and Drilling Parameter of Natural Fiber Composites with Usage of Epoxy Resin
Abstract: An attempt that has been made to take use of the advantages offered by natural composite materials in light of the fast advancement of research and development in this field over the course of the previous two decades, from the laboratory to the factory floor. During the manufacturing process of laminates, polymer matrices are used, while cotton, jute, and sisal are utilised as reinforcing materials. Epoxy resin is used to …
Published in Journal of Polymer & Composites · Vol. 11, Issue 4, 2023 · pp. 37–45 Read article
-
Intelligent Optimization of Drilling Parameters in Polymer Composites using Machine Learning and Metaheuristic Techniques
Abstract: The study tests different ways to use ML and metaheuristic algorithms to determine the best drilling parameters for polymer matrix composites. The research uses a composite matrix made from 55.25% vinyl ester, 44.0% Nickel–Phosphorous coated glass fiber and 0.75% Al₂O₃ nanowires which are tested for tensile strength (64.57 MPa), flexural strength (85.86 MPa) and impact strength (71.79 kJ/m²). By applying a Taguchi orthogonal array, it is observed that a slower …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1795–1810 Read article
-
Artificial Neural Network Modelling to Optimize Micro-Drilling Parameters of ECDM of Developed Novel Zn/(Ag+Fe)-MMC
Abstract: Several engineering fields have increased their use of metal matrix composites (MMCs) in the past few years. Due to the increase in composites, the demand for accurate machining has also become important. Specifically, pertaining to biomaterial applications, accuracy factor with desired surface finish is critical. While the near-net shape manufacturing process has advanced, MMCs frequently require post-mould machining to achieve surface quality, and dimensional tolerances. In the present study, a …
Published in Journal of Polymer & Composites · Vol. 11, Issue 1, 2023 · pp. 01–13 Read article
-
Evaluation of Physico-Chemical Parameters of Drilling Fluid and Its Effects on Water Quality Discharged in (Okoroagu River) in Etche LGA of Rivers State
Abstract: The study evaluated the surface water quality of Okoroagu River, Niger Delta of Nigeria, in order to determine the water quality index. Water samples were collected at five sampling points of the Okoroagu river. The results revealed that the Physicochemical and heavy metals parameters exceeded the NSDWQ and WHO recommended permissible limits except for TDS, pH, EC, Zinc, Chromium, Nickel and Manganese whicht were within the acceptable limit. The water …
Published in Journal of Water Pollution & Purification Research · Vol. 12, Issue 1, 2025 · pp. 32–44 Read article
-
Fabrication and drilling characterization of Hemp & Grewia-Optiva hybrid composite and comparison with ANN model
Abstract: In recent days the use of natural fibers has increased over synthetic fibers due to various advantages. The alkali treatment for these natural fibers further improves the adhesion between fiber and matrix and greatly enhances the mechanical properties of the composite. The present study involves the fabrication of a hybrid composite using the alkali-treated (5% NaOH concentration) natural fibers – Hemp &Grewia-optiva as reinforcement material and epoxy as a matrix …
Published in Journal of Polymer & Composites · Vol. 12, Issue 3, 2024 · pp. 138–146 Read article
-
AI-Driven Prediction of Square-Hole Laser Trepanning Performance in AA7075/15%SiC/15% Glass Fiber Hybrid Composites Using Taguchi–ANOVA and Deep Neural Networks
Abstract: Hybrid AA7075 composites reinforced with 15% silicon carbide (SiC) and 15% glass fiber were fabricated via the stir casting technique to improve machining and structural performance. The addition of dual reinforcements into the aluminum matrix was aimed at enhancing hardness, thermal stability, and surface quality during non-traditional drilling operations. Square-hole drilling was performed using a laser trepanning process, and the key responses—hole size accuracy, surface roughness, and taper angle—were systematically …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1932–1943 Read article
-
Use of Coconut Fibre as a Suitable pH and Rheology Enhancer
Abstract: This paper studied the use of coconut fibre as a substitute for caustic soda in drilling fluids for the improvement of pH in a water-based mud. The coconut coir was dried in the sun for 7 hours and ground into very fine particles, after which it was placed in an electronic oven at a temperature of 105°C for 1 hour to remove any remaining moisture. Sieving using a 200 mm …
Published in Journal of Petroleum Engineering & Technology · Vol. 14, Issue 3, 2024 · pp. 01–10 Read article