Search
10 articles for “CST-MW”
-
An Extended Semi-circular Microstrip Patch Antenna with DGS for UWB Applications
Abstract: This paper presents the design of a semicircular patch with an extended length for UWB applications. The proposed antenna is fabricated on FR4 substrate with relative permittivity of =4.4 and dimensions of 29.5x38x1.57 . The feed used in proposed design is 50 Ω microstrip feed line. The partial ground structure with a T-shaped slot and dual right angled isosceles triangular notches of side 3 mm each has been introduced to …
Published in Journal of Microwave Engineering and Technologies · Vol. 4, Issue 1, 2017 · pp. 13–18 Read article
-
RF Energy Harvesting from Wi-Fi Router in 2.45 GHz ISM Band
Abstract: In this paper, an experimental RF energy harvesting system using rectifying antenna (rectenna) to harvest ambient energy from Wi-Fi at 2.45 GHz is presented. The proposed circuit is a combination of RMPA, followed by a third order stepped impedance low-pass filter, matching network and rectifier using Schottky diode for microwave (RF) to DC conversion. The performance of the rectenna is simulated by electromagnetic simulator computer simulation technology (CST) microwave studio. …
Published in Journal of Microwave Engineering and Technologies · Vol. 2, Issue 3, 2015 · pp. 21–25 Read article
-
Design of Triple Band Microstrip Yagi Uda Antenna
Abstract: Abstract A microstrip yagi uda antenna with triple band is proposed in this paper. The design antenna consists of CPW feeding in which the ground plane and the yagi antenna are on the same plane. The resonating frequency of design antenna is 6.29, 7.97 and 9.26 GHz. The antenna had achieved the directivity of 5.232, 5.704 and 6.062 dBi. The impedance of antenna is completely matched at all the three …
Published in Current Trends in Information Technology · Vol. 3, Issue 2, 2013 · pp. 7–10 Read article
-
Design of Microstrip Yagi Uda Antenna by Using Triangular Patches
Abstract: AbstractA novel design of microstrip yagi uda antenna by using triangular patches at resonating frequency of 9.4 GHz is proposed in this paper. The microstrip antenna is designed by using triangular patches which improves the gain, directivity and efficiency of the antenna. The microstrip yagi uda antenna was simulated by Computer simulation technique (CST) MW studio software. In this paper, the simulated results such as radiation pattern, input impedance, return …
Published in Current Trends in Information Technology · Vol. 3, Issue 1, 2013 · pp. 21–23 Read article
-
Compact MIMO Antenna Array based on Koch Fractal Metamaterial for 5G Applications
Abstract: In this paper, a design of a printed MIMO antenna array for 5G applications is proposed based on low profile structure. Thus, the antenna element is designed as a printed mender monopole with a partial ground plane. The partial ground plane is proposed to realize bandwidth enhancements through etching rectangular slots in the antenna back panel. It is found that such antenna shows two frequency bands, S11<-10dB, from 3 GHz …
Published in Journal of Microwave Engineering and Technologies · Vol. 9, Issue 3, 2022 · pp. 1–7 Read article
-
A Hexagonal Sierpinski Gasket Antenna with a Microstrip Feed Line and a Stub for UWB Applications
Abstract: In this paper a Sierpinski gasket hexagonal antenna is proposed with a feed line having a stub attached to it. Three iterations of the proposed antenna geometry were done and with this improved feeding technique for four resonant bands of operation from 2.86 to 3.3 GHz, 3.758–4.313 GHz, 7.514–8.5468 GHz and 12.352–10.976 GHz were obtained. The antenna is suitable for ultra wideband (UWB) and radiolocation applications. The proposed antenna was …
Published in Journal of Electronic Design Technology · Vol. 6, Issue 1, 2015 · pp. 14–18 Read article
-
Design of UWB Microwave Filter Using Quarter Wavelength Short-Circuited Stub
Abstract: UWB technology has progressed a lot in recent years for high speed wireless communications and other applications which need higher data rate and wider bandwidth. In this paper UWB bandpass filter is designed using quarter wavelength (λ0/4) short circuited stubs to improve the performance of UWB. Designed UWB filter gives higher performance and lower insertion loss in UWB spectrum. 5th order UWB bandpass filter is designed using CST MWS simulation …
Published in Journal of Microwave Engineering and Technologies · Vol. 2, Issue 2, 2015 · pp. 32–36 Read article
-
Bandwidth and Return Loss Enhancement in Patch Antenna by Meta Material using at 2.62 GHz
Abstract: In this work, a rectangular micro strip patch antenna (RMPA) loaded with “Symmetric square Shapes Four Segments with circular rings structure” metamaterial structure is designed at a height 3.2 mm from ground plane by using CST-MWS software. The resonance frequency of the designed antenna is 2.62 GHz. The 10 dB impedance bandwidth of proposed antenna is increased up to 78.3 MHz. The return loss of the proposed antenna reduced to …
Published in Journal of Microwave Engineering and Technologies · Vol. 1, Issue 3, 2014 · pp. 33–37 Read article
-
A Novel Antenna Design based on a Single UC-PBG Layer of High Gain for Wireless Power Transfer
Abstract: In this study, a brand-new, highly effective antenna design is put forth to provide a directional radiation pattern with a small beam width for wireless power transfer. The proposed antenna is constructed from a cross-shaped patch of square holes. A favorable eclipse is paired with the antenna patch to provide circular polarization-symmetrical radiation. A symmetrical quadrature stare-shaped unit cell has a uniform compact photonic bandgap layer (UC-PBG) on top of …
Published in Journal of Microwave Engineering and Technologies · Vol. 9, Issue 3, 2022 · pp. 8–19 Read article
-
Enhancement in RMPA Parameters using Slotted Rhombus Connected Square Shaped Antenna with Left Handed Metamaterial
Abstract: In this paper, rectangular microstrip patch antenna (RMPA) along with metamaterial which has design of “slotted rhombus connected with rectangular shaped cover structure” is proposed at height of 3.2 mm from the ground plane. The RMPA with proposed metamaterial structure is designed to resonate at 2.7 GHz frequency. This work is mainly focused on increasing the potential parameters of microstrip patch antenna. Proposed metamaterial design structure significantly reduces the return …
Published in Journal of VLSI Design Tools and Technology · Vol. 7, Issue 1, 2017 · pp. 49–54 Read article