Search
428 articles for “tensile”
-
Enhancing Concrete Performance With GGBFS: An Analysis of Strength Characteristics at Various Replacement Levels
Abstract: This study investigates the effect of ground-granulated blast furnace slag (GGBFS) as a partial replacement for cement on the mechanical properties of concrete. The primary objective was to assess the compressive, flexural, and split tensile strengths, along with the modulus of elasticity, at different replacement levels of cement with GGBFS and at distinct curing ages of 7, 28, and 56 days. Concrete mixes were prepared by replacing cement with GGBFS …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 121–138 Read article
-
Finite Element Analysis of Multiwall Carbon Nanotubes Enabled Single Lap Joint
Abstract: This study uses finite element analysis (FEA) to examine the strength of adhesively bonded single lap joints with and without Multiwall Carbon Nanotubes (MWCNT) added to the adhesive. Shear strength analysis is performed by applying a tensile load that generates shear stress at the overlap between the two substrates bonded with adhesive. Aluminum (Al-Al) substrates were used, and single-lap joints were prepared following ASTM standards. Specimens with identical overlap and …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 195–203 Read article
-
Development of Robot Arm Fingers with Polymer Soft Materials
Abstract: Lightweight soft material applications have attracted attention to Basalt Fiber Reinforced Polymer (BFRP) laminates because of their impressive mechanical characteristics. The impact response and stress-strain behavior of epoxy resin laminates armored with basalt fiber and banana fiber are investigated during this project using computational and experimental approaches. The hand lay-up method was employed to create laminates with a thickness of 3 mm, dimensions of 300x300 mm², and a layout of …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 432–439 Read article
-
High-Performance Aluminum Matrix Composites Reinforced with Graphene Nanoplatelets a Study on Mechanical and Thermal Behaviour
Abstract: This study investigates the effect of graphene nanoplatelets (GNPs) on the mechanical and thermal properties of aluminum matrix composites (AMCs) fabricated using the powder metallurgy route. Aluminum alloy Al-6061 powder was reinforced with varying GNP concentrations (0, 0.5, 1, 2, and 3 wt%), followed by uniaxial compaction and sintering. The influence of GNP content on the composite’s structural integrity, strength, and thermal behavior was thoroughly evaluated through tensile testing, hardness …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 38–49 Read article
-
Enhancing Physical Properties of Unfilled SBR Rubber Compounds using Nano CaCO3 Additive
Abstract: The push for rubber compounds with improved characteristics in the rubber industry has sparked extensive research strategies for developing novel rubber compounds with improved properties like tensile strength, abrasion resistance, rolling resistance and flex properties etc., especially for the automobile industry. To intensify the processability, performance, and look of materials such as plastics, rubbers, paints, color, printing, and lubricants, additives are often employed to improve their qualities and overall value …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 40–49 Read article
-
Development of Chilli Pedicle Powder Fiber Reinforced with Palmyra Sprouts for Sustainable Biodegradable Composites and Its Mechanical Characterization
Abstract: The current research study aimed to present the development and mechanical characterization of a novel biodegradable composite material, Chilli Pedicle Powder fiber reinforced with Palmyra sprouts, which might be of significant importance to replace conventionally used synthetic fibers from nature in an eco-friendly way. With rising global needs in sustainable materials in multiple industries, like automotive, construction, and packaging industries, it was required to find an alternative biodegradable source that …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 433–441 Read article
-
Machine Learning-Assisted Design and Optimization of Lightweight Polymer Composites for IoT-Enabled Automotive Applications
Abstract: This study aims to develop an integrated machine learning and optimization framework for the intelligent design of lightweight polymer composites suited for IoT-enabled automotive applications. The goal is to enhance material performance while satisfying multiple design constraints such as mechanical strength, thermal stability, and process compatibility. A curated dataset of polymer composite formulations was used to train a Random Forest Regression (RFR) model capable of predicting tensile strength, thermal conductivity, …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 12–27 Read article
-
New Design Formulae for Safety and Precision in the Fatigue Engineering of Mechanical Components and Structures
Abstract: This paper introduces two new formulae, termed the Nori Fatigue Formulae, for determining the maximum allowable fatigue stress in mechanical components and structures with significant stress concentrations. These formulae will eliminate the usage of code-sensitive safety factors along with other factored values from the entire mechanical design engineering work, ranging from a safety pin to spacecraft. The first formula gives the maximum allowable fatigue stress in tension, and the second …
Published in Trends in Mechanical Engineering & Technology · Vol. 16, Issue 1, 2026 · pp. 6–24 Read article
-
Mechanical Characterization of Kevlar 49 and Pina Fiber Hybrid Composites
Abstract: The pursuit of sustainable yet high-performance materials has accelerated research into hybrid composites that combine synthetic and natural fibers. This study investigates the fabrication and characterization of a Kevlar 49/Pina fiber hybrid composite using epoxy resin as the matrix. Kevlar 49, known for its exceptional tensile strength and energy absorption, was employed as the face sheet material, while Pina fiber, a biodegradable reinforcement extracted from pineapple leaves, was incorporated as …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 301–316 Read article
-
Bio-Derived TPS–Lignin Hybrid Composites Reinforced with Modified Coir and Plantain Fibers for Eco-Efficient Structural Applications
Abstract: This study develops bio-derived polymer composites using a thermoplastic starch–lignin (TPS–lignin) matrix reinforced with alkali-treated coir and plantain fibers for sustainable load-bearing applications. The TPS–lignin matrix was formulated using cassava starch, glycerol, and 10 wt% lignin, while coir and plantain fibers were surface-modified using 5 wt% NaOH to enhance interfacial compatibility. Composite laminates were fabricated with varying fiber loadings (10–40 wt%) through melt-mixing and hot-press compression. Tensile, thermal, morphological, and …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 136–145 Read article
-
Experimental Evaluation of Carbon Fiber Reinforced Epoxy Composites for Structural Applications
Abstract: Composites made of carbon fibre reinforced polymer (CFRP) are currently one of the most widely used material classes in advanced engineering applications because of their remarkable environmental resistance, dimensional stability, and strength-to-weight ratio. The vacuum bag moulding method was used in this study to create CFRP laminates with different fiber-to-resin weight ratios: 50:50, 55:45, 60:40, 65:35, and 70:30. The reinforcement phase was made of unidirectional carbon fibre fabric and the …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 401–415 Read article
-
Investigating The Influence of Sic Reinforcement on The Mechanical and Tribological Properties of PA12 Polymer Composites in SLS
Abstract: The study investigates the mechanical and tribological performance of neat PA12 polymer and SiC-reinforced PA12 polymer composites made via Selective Laser Sintering (SLS). To evaluate just how reinforcement has influence upon overall performance, we incorporated into the PA12 polymer matrix a constant amount of 5 wt.% of Silicon Carbide (SiC). Mechanical testing focused on both tensile and fatigue behavior and testers conducted it with a Servo-Hydraulic Multipurpose High-Capacity Fatigue Test …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 541–554 Read article
-
Mechanical Characterization of Prosopis Juliflora Fibre-Reinforced Epoxy Composites for Sustainable Automotive Applications
Abstract: This study investigates the potential of Prosopis juliflora (PJ) fibre as an eco-friendly, economical, and mechanically efficient reinforcement for epoxy-based polymer composites. Composite samples were produced using the compression moulding technique with epoxy-to-fibre weight ratios of 90:10, 85:15, and 80:20. Mechanical tests, including tensile, flexural, impact, and hardness evaluations, were conducted in accordance with relevant ASTM standards. The incorporation of PJ fibre resulted in significant improvements in the mechanical behaviour …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1720–1728 Read article
-
Exploring the Dynamic Mechanical Analysis and Biocompatibility of Compression-Molded PMMA for Biomaterial Applications
Abstract: Metals such as titanium, cobalt, and magnesium are commonly used as biomaterials. However, their use can lead to tissue reactions due to the formation of foreign bodies which may cause blood cancer. Researchers have addressed this issue by substituting biomaterials with polymethyl methacrylate materials (PMMA). The PMMA material being studied is produced using the compression molding technique. This article examines the mechanical properties and biotoxicity of PMMA. These materials have …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 482–499 Read article
-
Enhancement of Mechanical Properties in Eutectic Al-Si Alloy Matrix Composites Reinforced with Kyanite and Graphite via Stir Casting
Abstract: The purpose of this work is to enhance the mechanical performance of a eutectic Al–Si alloy by incorporating hard ceramic (kyanite) and soft solid lubricant (graphite) reinforcements using a liquid-state stir casting route. Metal matrix composites were fabricated with kyanite contents of 2, 4, and 6 wt.% and a constant 2.5 wt.% graphite. Their microstructures and mechanical properties were systematically evaluated. The microstructure was examined using optical microscopy and energy …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 90–100 Read article
-
Structural Assessment of Rigid Pavement Systems Under Heavy Loading Conditions
Abstract: This study presents an analysis of pavement and foundation layer design subjected to heavy vertical loads and upward soil pressure. A total load of 1716 tonnes transmitted from the superstructure is considered acting on the pavement system. Due to upward soil pressure, tensile stresses develop in the foundation layers, requiring adequate thickness of sand and aggregate layers to ensure structural stability. Based on the tensile strength of sand (2 N/mm²), …
Published in Trends in Transport Engineering and Applications · Vol. 13, Issue 1, 2026 · pp. 36–48 Read article
-
Interfacial Engineering of Carbon Fiber/Epoxy Laminates Using Functionalized Graphene Nanoplatelets: Experimental and Numerical Study
Abstract: Current research work studies the influence of amines(–NH₂) and carboxyl(–COOH) functionalized graphene nanoplatelets on the mechanical and thermomechanical behavior of unidirectional hybrid composite. Composites having different graphene concentration from 0 to 0.7 wt% were fabricated, characterized and analyzed for multiple testing - tensile testing, dynamic mechanical analysis (DMA) and Fourier transform infrared spectroscopy (FTIR). Tensile testing indicates better elastic modulus and tensile strength due to efficient load transfer between nanoparticles …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 61–77 Read article
-
Enhancement of Mechanical and Tribological Properties of Aluminum-Titanium Carbide (Al-TiC) Metal Matrix Composites via Powder Metallurgy
Abstract: Metal matrix composites (MMCs) have emerged as a result of the increasing need for sophisticated lightweight materials with exceptional mechanical and tribological qualities. For structural and wear-critical applications, aluminum-based composites supplemented with ceramic particles such as titanium carbide (TiC) have shown great promise. In this work, aluminum-TiC composites made by powder metallurgy a process that guarantees even particle dispersion, regulated porosity, and the creation of near-net shapes are fabricated, mechanically …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 366–374 Read article
-
Mechanical Characterization and Machinability Optimization of Stir-Cast Al6061–SiC Metal Matrix Composites
Abstract: This study presents the fabrication, mechanical characterization, metallurgical analysis, and machinability optimization of Aluminum 6061 reinforced with Silicon Carbide (SiC) metal matrix composites (MMCs) at three weight fractions: 5%, 7.5%, and 10%. Composites were manufactured using the stir casting technique, followed by comprehensive mechanical testing (tensile, hardness, and impact), optical microscopy, and scanning electron microscopy (SEM). Machinability was assessed through turning experiments on a lathe using an L9 Taguchi orthogonal …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 Read article
-
Characterization of Mechanical and Viscoelastic Properties of Ceramic Nanoparticle-Reinforced Polymer Composites
Abstract: This study examines the mechanical and viscoelastic properties of polymer composites reinforced with ceramic nanoparticles, specifically focusing on enhancing the performance of the material through the incorporation of alumina nanoparticles. The composites were produced by embedding alumina nanoparticles into an epoxy matrix, and their properties were assessed using tensile, flexural, and dynamic mechanical analyses (DMA). The tensile tests showed a remarkable 40% increase in tensile strength and a 35% enhancement …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 71–82 Read article