Search
380 articles for “compressive”
-
Physico-Mechanical Behavior of Euphorbia Abysinica and Wood Chips Composite
Abstract: In this study, we prepared composite test specimens from Eucalyptus chip particles of sizes 0.5 mm, 1 mm, and 2 mm combined with Euphorbia-Abyssinica fluid at an 80:20 mass ratio. We produced the particleboard under a compression load of 150 KN and kept it in the compression machine for thirty minutes inside the mold. After removing it from the machine, we secured it with C-clamps for twenty-four hours. We covered …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 Read article
-
Analysis of Crashworthiness of a Saloon Car Fitted with CNG Cylinder
Abstract: There is an increase in demand for compressed natural gas vehicles in India. Due to the high gasoline prices and lack of electric vehicle infrastructure in India, compressed natural gas vehicles are the only feasible option. This research work focuses on the crashworthiness of a saloon car fitted with a compressed natural gas cylinder under rear-collision conditions. Four different candidate materials of the same thickness are chosen for the cylinder …
Published in Journal of Polymer & Composites Read article
-
Empowering Concrete: Enhancing Strength and Durability with Coal Bottom Ash
Abstract: The utilization of coal bottom ash, an industrial waste byproduct, as a sustainable alternative to river sand in concrete production has gained increasing attention due to environmental concerns and the need for resource optimization. This study examines how incorporating coal bottom ash into concrete mixtures, either partially or entirely replacing river sands, affects different properties. These properties include the workability of fresh concrete, as well as its compressive strength, splitting …
Published in Recent Trends in Civil Engineering & Technology · Vol. 14, Issue 1, 2024 Read article
-
Geopolymer Concrete with Cenosphere as Fine Aggregate: A Material Characterisation
Abstract: Geopolymer concrete (GPC) is regarded as the successor to traditional concrete as it eliminates the requirement for conventional Portland cement during its manufacturing process, hence decreasing CO2 emissions. This study employed Cenosphere, which are lightweight fine materials, to partially substitute the volume of sand in GPC. Cenosphere was utilized in proportions of 20%, 40%, 60%, and 100%. This experiment examined the fresh and hardened characteristics, durability against freezing and thawing, …
Published in Journal of Polymer & Composites · Vol. 12, Issue 1, 2024 · pp. 143–151 Read article
-
Design and Assessment of Fixed Dose Combination Containing Fenofibrate and Pravastatin Sodium in Tablet Formulation: A Bioinformatics Approach
Abstract: The aim of this is study is to formulate and evaluate fixed dose combination of Fenofibrate and Pravastatin sodium in tablet dosage for the treatment of Dyslipidemia. For the formulation and optimization of fenofibrate layer, two factor three level factorial design was used as experimental design for optimization with a minimum of nine run. All the nine trial (F1–F9) has been formulated according to the experimental design by wet granulation …
Published in Research & Reviews: A Journal of Bioinformatics · Vol. 11, Issue 1, 2024 · pp. 1–20 Read article
-
Investigation on Mechanical Properties of Geo Polymer Concrete With Fly Ash and Steel Fibers
Abstract: The goal of this project was to manufacture fly ash-based geopolymer concrete (FAC), a more environmentally friendly substitute for conventional Portland cement concrete (OPC) by using fly ash (FA) in place of cement. The study discovered that the properties of FAC were comparable to those of OPC, and that the concrete's performance was greatly impacted by the geopolymer's polymeric nature. The geopolymerization process was started with an alkaline solution, and …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 250–260 Read article
-
Optimization of Polymer-Enhanced Sustainable Concrete: A Composite Approach with Bentonite and Crumb Rubber Aggregates
Abstract: The disposal of rubber tyres has become challenging; on the other hand, the utilization of rubber tyres is also increasing daily in society. The successful use of crumb rubber as an alternative aggregate and bentonite as a partial cement replacement in concrete composites has been well established through prior research. These materials have individually demonstrated their potential to enhance sustainability, improve concrete properties, and reduce environmental impact, paving the way …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 701–715 Read article
-
Design and Performance Analysis of Sustainable Hybrid Composites for Impact Absorption and Lightweight Applications.
Abstract: This study explores the mechanical and structural properties of a novel hybrid composite composed of recycled tyre rubber, ceramics, and wood. The investigation focuses on key parameters, including energy absorption, compressive and tensile strength, and density, to evaluate the composite's suitability for diverse applications. The impact energy absorption test revealed that Sample A, comprising 50% rubber, 25% ceramic, and 25% wood, exhibited the highest energy absorption capability, with an average …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 95–104 Read article
-
Enhancing Concrete Performance With GGBFS: An Analysis of Strength Characteristics at Various Replacement Levels
Abstract: This study investigates the effect of ground-granulated blast furnace slag (GGBFS) as a partial replacement for cement on the mechanical properties of concrete. The primary objective was to assess the compressive, flexural, and split tensile strengths, along with the modulus of elasticity, at different replacement levels of cement with GGBFS and at distinct curing ages of 7, 28, and 56 days. Concrete mixes were prepared by replacing cement with GGBFS …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 121–138 Read article
-
Influence of Nanomaterial on Biofuel Extracted from Lemon Seed Feedstock
Abstract: Biodiesel, which is a type of biofuel, offers a replacement to the traditional diesel fuel currently available on the market, which is derived from petroleum that is both more sustainable for the environment and more attractive from an economic standpoint. A plethora of environmental benefits can be obtained through the utilization of this technology, including a reduction in emissions of greenhouse gases and particulate matter, as well as the possibility …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 200–210 Read article
-
Soil Stabilized Road
Abstract: This research examines the suitability of soil-stabilized roadways for light vehicular movement, offering an economical and practical alternative for areas with limited infrastructure development. Stabilizing soil involves improving its engineering properties by incorporating additives such as cement, lime, or other binding materials. Through stabilization, the treated soil can achieve a compressive strength of approximately 5 N/mm², or 500 tonnes per square meter (t/m²), which is sufficient to support loads imposed …
Published in Journal of Geotechnical Engineering · Vol. 12, Issue 2, 2025 · pp. 38–42 Read article
-
Investigation of Mechanical Properties of Hollow Bricks Incorporating Aerated Aggregates: A Polymer-Cement Composite Approach
Abstract: The rapid advancement of construction technologies has necessitated the development of lightweight, thermally efficient, and sustainable building materials. Hollow bricks, due to their inherent voids, offer substantial reductions in dead load and enhanced insulation properties. However, their mechanical performance often falls short when compared to conventional solid bricks. To address this limitation, this study explores the synergistic integration of aerated aggregates and polymer-cement composites (PCCs) in hollow brick production. Aerated …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 92–105 Read article
-
Effect of Span, Load Intensity, and Beam Geometry on Stress and Deflection Behavior of RCC Beams
Abstract: This study investigates the influence of variations in beam geometry, span, load intensity, and permissible stresses on the structural behavior of reinforced concrete beams. Using classical bending and shear stress formulations, the effects of a 20% increase in key parameters were analytically evaluated. Results indicate that a 20% increase in beam span leads to a proportional 20% increase in beam depth, whereas a 20% increase in beam width or permissible …
Published in Journal of Structural Engineering and Management · Vol. 13, Issue 1, 2026 · pp. 9–22 Read article
-
Improving Black Cotton Soil with Sodium Hydroxide and Fly Ash: An Assessment of Optimum Moisture Content, Dry Density, and California Bearing Ratio
Abstract: This study investigates the stabilization of Black Cotton Soil (BCS), an expansive clayey soil primarily composed of montmorillonite minerals, using sodium hydroxide (NaOH) and fly ash. Due to its high plasticity and significant volume changes with moisture, BCS is challenging for construction purposes. Adding NaOH and fly ash can potentially improve the soil's moisture tolerance, compressibility, and reduce its plasticity, making it more suitable for structural applications. The research evaluates …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 192–201 Read article
-
Enhancement of Mechanical and Tribological Properties of Aluminum-Titanium Carbide (Al-TiC) Metal Matrix Composites via Powder Metallurgy
Abstract: Metal matrix composites (MMCs) have emerged as a result of the increasing need for sophisticated lightweight materials with exceptional mechanical and tribological qualities. For structural and wear-critical applications, aluminum-based composites supplemented with ceramic particles such as titanium carbide (TiC) have shown great promise. In this work, aluminum-TiC composites made by powder metallurgy a process that guarantees even particle dispersion, regulated porosity, and the creation of near-net shapes are fabricated, mechanically …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 366–374 Read article
-
Microbially Modified Sustainable Cementitious Composites Using Industrial Ash Fillers
Abstract: The growing demand for sustainable, durable construction materials has driven the development of bio-engineered cementitious composites incorporating industrial by-products and self-healing mechanisms. This study investigates a microbially modified cementitious composite that integrates industrial ash fillers with bacteria-based self-healing technology to enhance mechanical performance and microstructural integrity while reducing cement consumption. Cement was partially replaced with industrial ash at 20%, 30%, and 40% replacement levels, and a uratolytic bacterial strain (Bacillus …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 331–350 Read article
-
A Study of Composite Concrete Using Palm Oil Fuel Ash (POFA) as a Partial Replacement for Cement in Self Compacting Concrete
Abstract: Due to its flexibility at young ages and its capacity to be moulded into any necessary structural form and shape, concrete is the most commonly used construction material. For concrete to be workable and to have the necessary strength and durability, thorough compaction utilising vibration is typically necessary. Large numbers of voids are caused by inadequate concrete compaction affecting the structural strength and long-term toughness. Self-Compacting Concrete (SCC) offers a …
Published in Journal of Polymer & Composites · Vol. 11, Issue 1, 2023 · pp. 76–86 Read article
-
Recognition of Engine Parameters for Mahua Biodiesel by Analyzing the Performance Using OFAT Approach
Abstract: The review work deals with the prediction of significant engine input parameters by the use of one factor at a time approach. The technique is a trial of experiments by varying only one engine input parameter and others remain at constant values. The various engine input parameters are found from the literature review. In the current work, six engine input parameters are predicted from the past research. These are blending …
Published in International Journal of Environmental Noise and Pollution Control · Vol. 1, Issue 1, 2023 · pp. 1–10 Read article
-
Managing Carpal Tunnel Syndrome: Insights into Symptoms and Relief
Abstract: Carpal tunnel syndrome (CTS) is a prevalent and concerning issue affecting the wrist and hand, arising from the compression of the median nerve within the carpal tunnel. This compression results in a spectrum of distressing symptoms, including numbness, tingling, weakness, and discomfort, particularly in the thumb, index, and middle fingers. Despite its frequent association with repetitive hand movements and prolonged use of computers or handheld devices, CTS can stem from …
Published in International Journal of Orthopedic Nursing and Practices · Vol. 1, Issue 2, 2023 · pp. 6–12 Read article
-
Effects of Nano Additives on Performance and Emission Characteristics of CI Engine with Mahua Biodiesel and Diesel Blends as Fuel
Abstract: Due to growing environmental concerns and the imminent depletion of fossil fuels, the development of eco-friendly alternative fuels, such as biodiesel, is imperative. To improve the performance and emission properties of diesel engines utilizing biodiesel blends, the effective introduction of metallic and non-metallic nano-additives has been established. This research aimed to investigate the blending ratios of biodiesel (B0, B10, B20, and B40) in a compression ignition engine. Furthermore, the impact …
Published in Journal of Polymer & Composites · Vol. 11, Issue 13, 2023 · pp. 41–49 Read article