Search
135 articles for “polymer–composite interfaces”
-
Experimental and Numerical Investigation of Corrosion-Induced Failures in Copper-Tin Alloy (Cu-Sn) and Aluminum-Magnesium Alloy (Al-Mg) Connectors: A Stress–Corrosion Coupling Analysis
Abstract: The utilization of an integrated experimental and finite element modelling (FEM) methodology, this study investigates the degradation and failure mechanisms in polymer composite electrical connectors exposed to aggressive environmental conditions. Epoxy- and polyamide-based composites, reinforced with carbon and glass fibers, were subjected to accelerated salt spray and humidity–temperature cycles to simulate prolonged outdoor exposure. Electrochemical and environmental aging experiments revealed that chloride ions and moisture ingress were responsible for matrix …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 366–379 Read article
-
Development and Performance Evaluation of Polymer-Modified Geopolymer Composites Incorporating GGBS
Abstract: This research investigates the development and performance of geopolymer-based composite materials formulated using Ground Granulated Blast Furnace Slag (GGBS) as a reactive mineral component within an aluminosilicate polymer matrix. The study aims to create an eco-efficient and structurally sound inorganic polymer composite comparable to M35-grade concrete, produced entirely under ambient curing conditions. A series of mixes with varying GGBS replacement ratios (0–100%) was prepared, maintaining a constant binder content of …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1145–1165 Read article
-
Synthesis of Glass Fiber Reinforced Polymer Composites Incorporating MWCNTS and Graphene: A Study on Dynamic Mechanical Behavior and Cole–Cole Representation
Abstract: Glass fiber reinforced polymer (GFRP) composites were fabricated using multi-walled carbon nanotubes (MWCNTs) and graphene as nanofillers through the hand lay-up technique. Two sets of composites were prepared by incorporating MWCNTs and graphene separately into the epoxy resin matrix at varying weight percentages (2%, 4%, 6%, 8%, and 10%). Mechanical and viscoelastic properties were evaluated following ASTM standards, and Dynamic Mechanical Analysis (DMA) was performed to study their mechanical and …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1411–1403 Read article
-
Interfacial and Tribo-Mechanical Performance of a TiO₂–Castor Oil Polymeric Nanofluid During Sustainable Machining of AISI 316L Stainless Steel Under MQL Conditions
Abstract: This research examines the tribo-mechanical performance and interfacial film characteristics of a TiO₂-reinforced castor-oil polymeric nanofluid during the turning of AISI 316L stainless steel under minimum-quantity lubrication (MQL). A Taguchi L9 orthogonal array was utilized to assess the synergistic effects of cutting speed, depth of cut, and coolant composition on surface integrity, while machining experiments were performed under dry, conventional, and TiO₂-nanofluid lubrication techniques. ANOVA and multiple-regression modeling were used …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 901–914 Read article
-
Development of a Polymer-Encapsulated IoT-Based Sensor for Thermal and Electrical Protection of EV Batteries
Abstract: Electric Vehicles (EVs) mark a critical shift toward sustainable transportation, with Battery Management Systems (BMS) playing a vital role in ensuring battery safety, reliability, and efficiency. The proposed BMS in this project incorporates real-time charge monitoring, temperature sensing, and fire detection capabilities to address safety concerns associated with lithium-ion batteries. Key features include current and voltage tracking, State of Charge (SoC) estimation, fault detection, and a user-friendly LCD interface. By …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 582–591 Read article
-
Development and Evaluation of Sodium Hydroxide-Treated Jujube Pit Reinforced Epoxy Composites
Abstract: The automotive sector has experienced a tremendous transformation, propelled by the increasing demand for materials that provide a balance between mechanical performance, economic efficiency, and environmental sustainability. In accordance with worldwide sustainability goals, the trend has moved toward the utilization of lightweight, recyclable, and biodegradable materials in modern vehicle architecture. Natural composite materials, which are derived from renewable resources such as seeds, leaves, and tree barks, have gained considerable attention …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 494–501 Read article
-
Sustainable Polymer Composites Reinforced with Natural Fibers: Processing, Properties, and Applications
Abstract: The environmental footprint of synthetic plastics has led to extensive studies of sustainable polymer composites reinforced with natural fibers like jute, sisal, hemp, flax, and coir. These biocomposites offer a greener solution to the conventional petroleum-based materials, which blends biodegradability and competitive mechanical characteristics. The present paper focuses on the processing methods, mechanical and thermal characteristics, and the possible application of natural fiber-reinforced polymer composites (NFRPCs). A survey of 50 …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1663–1670 Read article
-
Impact of Reinforcement Materials and Processing Condition Optimization in Microstructural Engineering of Polymer Composites
Abstract: Polymer mixtures have gotten a lot of attention because they have a unique set of qualities that make them useful in many situations. But the substructure of these alloys is very important for getting the best performance. It looks at how to improve the microstructure of polymer composites by finding the best support materials and working conditions. The choice of strengthening materials is the first thing that is talked about. …
Published in Journal of Polymer & Composites · Vol. 12, Issue 4, 2024 · pp. 102–118 Read article
-
Polymer Electrolyte Films Doped with Nanofillers ZnO: Electrochemical and Optical Investigations
Abstract: The electrochemical and optical characteristics of polymer composite electrolyte films doped with zinc oxide (ZnO) nanofillers are thoroughly examined in this work. Because of its superior film-forming capacity, flexibility, and ionic transport properties, poly(vinyl alcohol) (PVA) mixed with potassium iodide (KI) is used as the host polymer electrolyte. To investigate their effects on ionic conductivity, dielectric behavior, and optical transmission, ZnO nanoparticles are synthesized and added to the PVA–KI matrix …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 320–332 Read article
-
Deep Learning-Enhanced Polymer-Based Wearable Biosensors for Continuous Health Tracking via IoT
Abstract: The rapid proliferation of wearable biosensor technologies has transformed approaches to real-time health monitoring, yet challenges persist in achieving both mechanical robustness and reliable, continuous data analytics in dynamic environments. Conventional polymer-based sensing systems often fall short due to limited signal fidelity, inadequate adaptive analytics, or insufficient integration with secure, low-latency IoT frameworks. Addressing these deficiencies, this work introduces a flexible, deep learning-enhanced wearable biosensor platform that combines a nanostructured …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 18–31 Read article
-
Synergistic Effect of Green Nanofillers on Basalt–Kenaf Reinforced Sustainable Polymer Composites
Abstract: This study examines the synergistic impact of green nanofillers on the mechanical and structural properties of basalt–kenaf fiber reinforced polyester composites, with the objective of developing sustainable, high-performance polymer materials. The composites were produced with different fiber ratios: B1 (70% basalt, 30% kenaf), B2 (60% basalt, 40% kenaf), and B3 (50% basalt, 50% kenaf), and were reinforced with 1 wt.% green-synthesized nano-TiO2, obtained using an eco-friendly sol–gel technique with plant …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 1248–1262 Read article
-
In-Situ Polymerized GO/PANI Composites: Structural Evolution, Optical Modulation, and NH₃ Sensing at Room Temperature
Abstract: Graphene oxide (GO)/polyaniline (PANI) composites with varying PANI contents (20, 40, and 60 wt%) were synthesized via in-situ oxidative polymerization and systematically investigated for their structural, morphological, optical, and gas-sensing properties. X-ray diffraction (XRD) confirmed a progressive increase in interlayer spacing and partial exfoliation of GO layers with increasing PANI content, indicating intercalation-assisted hybridization. Fourier transform infrared (FTIR) spectroscopy revealed the characteristic vibrational bands of both constituents and confirmed strong …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 Read article
-
Experimental Evaluation of Carbon Fiber Reinforced Epoxy Composites for Structural Applications
Abstract: Composites made of carbon fibre reinforced polymer (CFRP) are currently one of the most widely used material classes in advanced engineering applications because of their remarkable environmental resistance, dimensional stability, and strength-to-weight ratio. The vacuum bag moulding method was used in this study to create CFRP laminates with different fiber-to-resin weight ratios: 50:50, 55:45, 60:40, 65:35, and 70:30. The reinforcement phase was made of unidirectional carbon fibre fabric and the …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 401–415 Read article
-
Advances in Membrane Technology: A Comprehensive Review of Materials, Processes, and Applications
Abstract: Membrane technology has become a critical platform for sustainable separation processes across water treatment, energy generation, chemical processing, and healthcare. Over recent decades, advances in materials, fabrication methods, and process design have dramatically expanded the performance, efficiency, and applications of membrane-based systems. Polymeric membranes dominate the industry due to cost-effectiveness and scalability, while ceramic, metallic, and composite membranes offer enhanced thermal and chemical resistance for specialized environments. Nanostructured and bio-inspired …
Published in International Journal of Membranes · Vol. 2, Issue 2, 2025 · pp. 1–6 Read article
-
A Strategy of Nano-Calcite Fillers for Enhancing the Mechanical and Thermal Properties of Polypropylene Polymers
Abstract: Particulate polymer composites have gained popularity because of their many uses. For some, using high loadings to achieve desired attributes without compromising the material's mechanical properties or restricting its processability is desirable. It is possible to use surface active agents to improve characteristics and increase solid loading. Interface characteristics in highly packed particulate composites based on nano-calcite (nano-calcium carbonate) and polypropylene as a binder are the focus of the current …
Published in Journal of Modern Chemistry & Chemical Technology · Vol. 16, Issue 1, 2025 · pp. 20–29 Read article
-
Carbon-Al Synergy: Investigation of Fiber Stacking and Orientation on the Mechanical Properties of Al-CFRP Metal Matrix Composites
Abstract: The current study examines the mechanical behaviour of Aluminum-Carbon Fiber Reinforced Polymer (Al-CFRP) composites fabricated using compression moulding technique, a novel approach combining lightweight aluminium’s ductility with CFRP’s high strength-to-weight ratio. The polymer composites were fabricated by stacking aluminum alloy sheet of 0.5mm thickness and pre-impregnated by 12 layers of carbon fiber cloth of 200 gsm, with epoxy resin between layers, followed by consolidation under controlled temperature and pressure in …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 340–354 Read article
-
Investigation on The Effect of Carbon Fiber Reinforcement on The Mechanical and Physical Properties of FDM 3d Printed PLA
Abstract: In this work, the effects of annealing on the physical properties and mechanical behavior of short-carbon-fiber-reinforced polylactic acid (CF/PLA) composites made using fused deposition modeling (FDM) are systematically investigated. Pristine PLA and CF/PLA composites with 10% fibers have been made and evaluated in accordance with ASTM standards. Tensile, bending, and hardness tests were used to evaluate the performance of as-received and annealed composites. The tensile and hardness properties of PLA …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 284–298 Read article
-
Biopolymer-Based 3D Composite Scaffolds for Bone Tissue Engineering: Photothermal-Responsive Systems with Controlled Pt (IV) Prodrug Release
Abstract: Biopolymer-based composite scaffolds have attracted significant attention as multifunctional platforms at the intersection of polymer science, regenerative medicine, and cancer nanotherapy. In this study, a dual-functional scaffold was developed for simultaneous osteosarcoma treatment and bone regeneration using poly (L-lactic acid) (PLLA) reinforced with bioactive glass (BG) and integrated with a glutathione-responsive platinum (IV) prodrug system (PDA@Pt). To improve interfacial adhesion, photothermal conversion efficiency, and tumor-specific activation, the Pt (IV) prodrug …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 351–361 Read article
-
Design and Validation of an Artificial Intelligence-Driven Digital Twin for Real-Time Monitoring and Control in Polymer Composite Manufacturing
Abstract: Polymer Matrix Composites (PMCs) have become indispensable in high-performance sectors such as aerospace and automotive engineering, offering exceptional strength-to-weight ratios that outperform traditional metals in many demanding applications. However, the reliability of manufacturing PMCs via Vacuum-Assisted Resin Transfer Molding (VARTM) is frequently undermined by stochastic process variabilities. Unpredictable fluctuations in thermal history, preform permeability, resin rheology, and ambient conditions often lead to some defects; namely voids, dry spots, and incomplete …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 224–233 Read article
-
Crystalline and Polymeric Interactions in Multi- layered Bulletproof Glass: A Study of Ballistic Resistance and Structural Integrity
Abstract: Bulletproof glass is engineered to withstand high-impact projectiles, offering a critical line of defense in various industries such as banking, military, and armored vehicles. This study explores the structural composition, energy absorption mechanisms, and performance characteristics of bulletproof glass when exposed to ballistic threats. The glass consists of layered constructions, often involving polycarbonate and adhesive interfaces such as polyvinyl butyral, which enhance its energy absorption and resistance to projectiles. The …
Published in International Journal of Crystalline Materials · Vol. 1, Issue 2, 2024 · pp. 10–17 Read article