Search
1961 articles for “Disc” (ranking capped at the first 2,000 matches — narrow the search to see the rest)
-
Cost Effective Wastewater Treatment Technique for Bara Nulla Peshawar
Abstract: Various samples from Bara Nulla in Peshawar were collected and analyzed, using standard methods for various important wastewater parameters. The effluent discharge from the nulla is highly polluted in terms of its physical and chemical properties. Most of it parameters do not meet the requirements of Pak-EPA NEQS limitations set for industrial and domestic effluent discharge. The average wastewater characteristics of nulla in terms of COD, BOD, TDS, TSS, turbidity …
Published in Journal of Geotechnical Engineering · Vol. 2, Issue 1, 2015 · pp. 24–28 Read article
-
Efficacy of Strain Wedge Method Against Traditional p-y Method for Analysis of Piles Subjected to Different Load and Soil Condition: A Review
Abstract: Pile foundation plays a major role in design of structures as its lateral response dominates the design subjected to lateral loads. These loads acting on foundations may be sustained from traffic loading on a bridge pier or earth pressure in a retaining wall. As soil reaction and pile deflection affect each other for a lateral load, this becomes a very complex soil-structure interaction problem. There are many approaches or methods …
Published in Journal of Geotechnical Engineering · Vol. 10, Issue 2, 2023 · pp. 1–12 Read article
-
Optimization of Process Parameters in EDM Machine with AISI 304 Stainless Steel using TOPSIS
Abstract: The effective solution based on TOPSIS approach to determine the optimal process parameters in die sinking electrical discharge machining. Taguchi L9 orthogonal array is used to gather information regarding the process with less number of experimental runs. Experiments have been conducted using three process parameters such as peak current, gap voltage, pulse on time, with three levels are selected to optimize the multiple objectives. AISI 304 stainless steel as a …
Published in Journal of Industrial Safety Engineering · Vol. 3, Issue 3, 2016 · pp. 33–38 Read article
-
Analysis of Safety Behaviour of Workers under Small-Scale Construction Sites: A Case Study of Anambra State
Abstract: Small-scale construction companies are predominant in developing countries and it is the most hazardous place in construction sites. Accidents mostly occur on construction sites due to a high level of safety ignorance and the nonchalant attitude of workers and management. The research aimed to investigate the actual behaviour of workers at the selected sites in terms of safety compliance, nutrition, alcohol use and smoking. This is highly necessary due to …
Published in Journal of Industrial Safety Engineering · Vol. 9, Issue 3, 2022 · pp. 37–46 Read article
-
A Review on Smart society and innovations in education
Abstract: Today, discussions over the prospects of digital technology in education are increasingly viewed as part of the larger approach to educational innovation. Despite the fact that education systems and institutions are really not slow to react, important barriers appear to exist. Preventing digital technologies from attaining their complete potential in educational institutions and teaching and learning practices. Learners can learn more effectively, efficiently, flexibly, and comfortably due to the advancement …
Published in Journal of Instrumentation Technology & Innovations · Vol. 12, Issue 1, 2022 · pp. 1–5 Read article
-
Optimization of Process Parameters in Wire EDM of HCHCrD2 using RSM-based Multi-objective Genetic Algorithm
Abstract: While precision is of paramount importance in machining of high strength conductive materials, Wire Electrical Discharge Machining (WEDM) is preferred. In the present work, experimental study has been carried to identify the appropriate process parameter settings for wire electrical discharge machining of high carbon high chromium D2 steel (HCHCrD2). The process parameters such as pulse peak current, pulse duration, pulse-off time, wire feed, wire tension and flushing pressure are considered. …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 1, 2018 · pp. 6–10 Read article
-
Literature Survey of On-chip Architectures and Arbitration Algorithms
Abstract: Today micro-electronic products are influencing the ways of communication, learning and entertainment. The key driving force for the developments during decades is the System-on-Chip (SoC) technologies, where complex applications are integrated onto single ULSI chips. Not only functionally enriched, these products such as mobile phones, notebooks and personal handheld sets are becoming faster, smaller-in-size, larger-in-capacity, lighter-in-weight, lower-in-power-consumption and cheaper. In this survey, communication architectures of SoC are discussed whose design …
Published in Journal of Microcontroller Engineering and Applications · Vol. 4, Issue 1, 2017 · pp. 17–23 Read article
-
Investigation on Spar Platform for Low Capacity Vertical Axis Wind Turbine in Shallow Water Deployment
Abstract: In this paper, we discuss hydrodynamic analysis on the three different design of spar buoyancy platform utilize for floating vertical axis wind turbine. The major parameter like diameter of platform at cut water plane and length of spar buoyancy platform are selected as variable to carry out design of experiments. The systematic investigation is carried out to determine minimum ballast weight to ensure stability of floating platform under Pitch, Roll …
Published in Journal of Microcontroller Engineering and Applications · Vol. 7, Issue 3, 2020 · pp. 27–36 Read article
-
A Review on Chiral Metamaterials and its Applications in Antennas
Abstract: AbstractThis paper presents a review of the chiral metamaterials (CMM) and their different specific properties like circular dichroism, negative refractive index, and giant optical activity. The physical properties of metàmaterials circular dichroism and the method of retrieval of effective parameters of the CMM are discussed in detail. The various classes of the chiral metamaterial and their results of the simulation are presented. The study shows that the chiral metamaterials have …
Published in Journal of Microwave Engineering and Technologies · Vol. 5, Issue 2, 2018 · pp. 5–16 Read article
-
An Integrated Approach for Optical Router Design for High-Speed Data Centers
Abstract: AbstractData centers are the core of the networking. The users connect to top of rack (ToR) switches by various network topologies. Depending on topology designs and applications running on data centers decide the traffic characteristics. Due to cloud computing environment in many data center switches distinctive varieties of applications runs. Thus, traffic characteristics vary on various data center switches. This paper discusses the random and bursty traffic model for data …
Published in Journal of Microwave Engineering and Technologies · Vol. 6, Issue 3, 2019 · pp. 1–10 Read article
-
A Comprehensive Survey on Massive MIMO Systems
Abstract: During the last decades with the mobile data traffic exponentially growing, demands for increased cell density or increased number of antennas per access point. Massive multiple input multiple output (MIMO) was found to be one of the solution for the ever increasing data traffic demand. However due to the inter cell interference and largely varying quality of service , massive MIMO lacks to meet the expectations of the demands of …
Published in Journal of Microwave Engineering and Technologies · Vol. 8, Issue 3, 2021 · pp. 6–21 Read article
-
A Novel Antenna Design based on a Single UC-PBG Layer of High Gain for Wireless Power Transfer
Abstract: In this study, a brand-new, highly effective antenna design is put forth to provide a directional radiation pattern with a small beam width for wireless power transfer. The proposed antenna is constructed from a cross-shaped patch of square holes. A favorable eclipse is paired with the antenna patch to provide circular polarization-symmetrical radiation. A symmetrical quadrature stare-shaped unit cell has a uniform compact photonic bandgap layer (UC-PBG) on top of …
Published in Journal of Microwave Engineering and Technologies · Vol. 9, Issue 3, 2022 · pp. 8–19 Read article
-
Wear Behavior of Al-Alloy (Al-5 Mg) in-situ Reinforced TiB2 Particulate
Abstract: A research has been carried out for replacing Al monolithic alloys by aluminium (Al) based metal matrix composites (MMCs) in many engineering applications where high wear resistance and stiffness are required. In this paper, the investigated dry sliding wear behavior of TiB2 particulate reinforced composite of Al-Alloy (Al-5 Mg) is discussed. The in-situ Al-Alloy (Al-5 Mg) 10wt% TiB2 composite material were prepared by molten flux reaction synthesis using electric melting …
Published in Journal of Materials & Metallurgical Engineering · Vol. 4, Issue 3, 2014 · pp. 32–37 Read article
-
Parametric Optimization of Tool Wear Rate in Side Flushing form of Die Sink EDM of EN-31 Die Steel
Abstract: Electrical discharge machining (EDM) is one of the most extensively used non-conventional material removal processes for manufacturing geometrically complex or hard material parts that are extremely difficult to machine by conventional machining process. EDM researchers have concentrated on achieving faster and more efficient metal removal rate coupled with a reduction in tool wear and improved surface characteristics. In this paper, the operating performance measures of side flushing type of electrical …
Published in Journal of Materials & Metallurgical Engineering · Vol. 1, Issue 1-3, 2011 · pp. 72–80 Read article
-
Plastic Waste: An Environmental Blight
Abstract: A review gave the context of effect of pollution from plastic on humans, animals and environmental health. Plastic is becoming an environmental calamity. The majority of research has been done till date on effect of plastic pollution on marine ecosystem is a Centre of attention. Discharge and dumping of plastic waste into the rivers and oceans have increased in recent years. In 2015, 55% waste was discarded and only 20% …
Published in Journal of Materials & Metallurgical Engineering · Vol. 11, Issue 3, 2021 · pp. 33–37 Read article
-
Additive Manufacturing of rocket propulsion system
Abstract: In recent years plenty of research is going on to produce effective manufacturing techniques which can produce complex unique designs with reduced cost and lead time for aerospace applications. In this aspect, Additive manufacturing is getting a wide range of popularity in the aerospace manufacturing domain due to its vast applications and advantages. In terms of geometric flexibility and processing time, additive manufacturing outperforms conventionalmanufacturing processes. Additive manufacturing has found …
Published in Journal of Materials & Metallurgical Engineering · Vol. 12, Issue 2, 2022 · pp. 1–9 Read article
-
A Study on Flipped Learning Models in Engineering Pedagogy
Abstract: The aim of this article is to provide an overview of the existing knowledge and application of the flipped learning method within the realm of engineering education. This paper discusses Pedagogical logistics of Flipped learning models in engineering while examining various teaching models used in collegesand universities all over India, especially NITS and IIITs. It has been the mission of the author to focus on the implementation of integration various …
Published in Journal of Materials & Metallurgical Engineering · Vol. 13, Issue 2, 2023 · pp. 31–35 Read article
-
Efficient ADP Scheme for DWT Computation
Abstract: AbstractIn this paper, the lifting and flipping scheme for discrete wavelet transform (DWT) computation and proposed an area delay efficient lifting based DWT architecture. In this computation huge number of multipliers and adders are saved when lifting based 2-D DWT architecture implemented. The derived full-parallel lifting-based 1-level 2-D DWT structure involves half number of less multiplier than the flipping-based 2-D DWT structure. Compared with the existing lifting-based structure, the proposed …
Published in Journal of Microelectronics and Solid State Devices · Vol. 5, Issue 3, 2018 · pp. 22–26 Read article
-
Study of Current Conveyors for Signal Processing Applications
Abstract: Current conveyors are basic analog building blocks used for voltage as well as current processing applications. Current conveyors are used as a voltage or current buffer in many applications. They are used for high frequency, high bandwidth, high dynamic range, better linearity, high driving capability, low voltage and low power applications. Current conveyors modify the limitations of low impedance at the output, tradeoff between speed and bandwidth and constant gain …
Published in Journal of Microelectronics and Solid State Devices · Vol. 4, Issue 1, 2017 · pp. 7–14 Read article
-
Microgrid Stability and Control Issues: A Review
Abstract: Microgrid are the key solution to implement Smart Grid for integration of renewable and distributed energy resources. This paper presents a discussion on the stability and control issues of microgrid with their solution and it Investigates some aspects of stability in microgrids and A hierarchical coordination strategy with primary, secondary, and tertiary coordination are reviewed for economic operation of community microgrid. Due to these problems with the existing power system, …
Published in Journal of Microelectronics and Solid State Devices · Vol. 10, Issue 2, 2023 · pp. 37–47 Read article