Search
272 articles for “thermal generator”
-
Thermal Performance Analysis and Optimization of Pin-Fin Heat Sink Using CFD, Taguchi Method, and Machine Learning
Abstract: Efficient thermal management is essential for improving the performance and reliability of modern engineering systems and electronic devices. This study presents the design, simulation, and optimization of a pin-fin heat sink using SolidWorks for three-dimensional modeling and ANSYS for thermal and computational fluid dynamics (CFD) analysis. Four different pin-fin geometries, namely square, pentagon, octagon, and circular fins, are considered to evaluate their thermal performance under varying operating conditions. Aluminum is …
Published in Trends in Mechanical Engineering & Technology · Vol. 16, Issue 2, 2026 · pp. 8–20 Read article
-
Review of Thermal Performance of Solar Air Heaters: Influence of Composite Materials and Advanced Thermal Storage Techniques
Abstract: Solar air heaters (SAHs) are essential devices for capturing solar energy and converting it into heat, finding applications in steam generation, refrigeration, agricultural drying, and space and water heating in residential and commercial environments. However, the thermal performance of SAHs is often limited by the low heat transfer coefficient of air and the absence of solar energy during nighttime, impacting efficiency and reliability. To address these challenges, this study explores …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 488–506 Read article
-
Design Strategies of Polymer Composite Components for Sustainable Renewable Energy Microgrids
Abstract: Increasing power demand and variable performance requirements in renewable-energy systems motivate integrating advanced polymeric and composite materials into microgrid components to improve reliability and performance. This paper presents a design and control framework for a standalone microgrid that couples power-electronic and energy-conversion subsystems with polymer-composite–based components to enhance durability, thermal management, and electromagnetic shielding. The microgrid uses a doubly fed induction generator (DFIG) for wind generation to enable independent active …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 · pp. 63–71 Read article
-
Effect of Internal Heat Generation on the Onset of Rayleigh-Bѐnard Chandrashekar Convection in a Micropolar Fluid with Maxwell Cattàneo Law
Abstract: AbstractThe effect of result from the substitution of the classical Fourier law by the nonclassical Maxwell-Cattàneo law and influence of internal heat generation on the Rayleigh-Bѐnard Chandrashekar internal heat generation parameter has a significant impact on the thermal mode making the system unstable. The eigen value is obtained for free-free, rigid-free and rigid-rigid velocity boundary combinations with isothermal temperature on the spin-vanishing boundaries. The influence of various micropolar fluid parameters …
Published in Recent Trends in Fluid Mechanics · Vol. 5, Issue 1, 2018 · pp. 31–43 Read article
-
A High-Efficiency Fuzzy-Logic-Controlled Wireless Charger Enabling the Safe Integration of Electronics in Carbon Fiber Reinforced Polymer E-Bikes
Abstract: The integration of advanced electronics into structures made from carbon fiber reinforced polymers (CFRP) presents significant challenges, including thermal management constraints, electromagnetic interference (EMI), and the imperative for lightweight components. This study addresses these challenges by designing and validating a fuzzy logic-based wireless charging system specifically engineered for lightweight E-Bikes employing CFRP frames. The system mitigates thermal risks associated with the low thermal conductivity of polymer composites by implementing a …
Published in Journal of Polymer & Composites · Vol. 13, Issue 6, 2025 · pp. 1159–1172 Read article
-
Photovoltaics and Thermal Solar Technologies: Innovations for Sustainable Heating, Cooling, and Energy Efficiency
Abstract: Developments in renewable energy technology, in particular photovoltaics (PV) and solar thermal systems, have been fueled by a rising demand for energy worldwide and the pressing need to slow down climate change. These technologies provide greener options for heating, cooling, and energy production by lowering dependency on fossil fuels and greenhouse gas emissions. This study examines developments in solar thermal and photovoltaic technologies, their uses in commercial, industrial, and residential …
Published in Journal of Refrigeration, Air conditioning, Heating and ventilation · Vol. 12, Issue 1, 2025 · pp. 30–37 Read article
-
Simulation and Comparative Analysis of Energy Storage Systems for Light Electric Vehicle
Abstract: Now-a-days it can be seen that most of people are focusing on cycling for exercising and short distance traveling due to unhygienic lifestyles and increase in environmental pollution and its harmful effect on human. Looking at such circumstances this paper is focused on to generate electrical energy produced by the person via paddling and later consume the same energy for automatic running of the cycle. The demand for Electric Bikes …
Published in Journal of Microelectronics and Solid State Devices · Vol. 9, Issue 3, 2022 · pp. 28–39 Read article
-
Critical Review on Multifunctional Polymer Composites for Weight Reduction and AI Based Battery Thermal Management in Electric Vehicles
Abstract: The rapid growth of electric vehicles (EVs) has intensified the need for advanced materials and intelligent control systems capable of improving energy efficiency, driving range, thermal safety, and overall vehicle sustainability. This paper presents a critical review of multifunctional polymer composites and artificial intelligence-based battery thermal management systems (AI-BTMS) for next-generation EV applications. Polymer composites reinforced with carbon fibers, graphene, boron nitride, nanoclays, and carbon nanotubes offer significant advantages over …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 603–619 Read article
-
Numerical Design of An Off-grid Solar Photovoltaic System for Office Shelter
Abstract: Electricity is essential needs for domestic and office applications. Due to the shortcomings from the national grid, renewable resources are prepared for alternative power supply rather than fossil fuels generators which pollute the environment. To provide a constant power supply, an off-grid solar PV system should adequately be designed. This paper presents the design of an off-grid solar PV system for office shelter. Solar thermal and solar photovoltaic (PV) systems …
Published in Journal of Energy, Environment & Carbon Credits · Vol. 13, Issue 2, 2023 · pp. 68–76 Read article
-
Thermal analysis of sustainable composite material absorption refrigeration system for cold storage application
Abstract: Present study deals with thermal analysis of absorption refrigeration system (ARS) and generator-absorber heat exchanger (GAX) based absorption refrigeration system by using green composite like aqua-ammonia. Evaporator temperature is 0°C for cold storage application, condenser temperature is 50°C as per Indian weather condition, mass stream rate of strong solution through the pump is 1 kg/s, and effectiveness of solution heat exchanger and refrigerant heat exchanger is 0.7 considered for present …
Published in Journal of Polymer & Composites · Vol. 12, Issue 4, 2024 · pp. 18–27 Read article
-
A Review of Potential, Generation and Factors of Solar Energy
Abstract: AbstractPower is the integral part of today’s life. Renewable energy is the demand of time because of its great advantages like non-pollutant, abundant etc. Among all the energy sources, solar energy is most promising, quiet and clean source of energy. India receives great amount of solar radiation throughout its boundaries. This study is to review the potential of solar energy in India, it’s technological development and factors of solar cell.Keywords: …
Published in Journal of Thermal Engineering and Applications · Vol. 5, Issue 2, 2018 · pp. 1–4 Read article
-
Compact PV-PCM System with Heat Recovery Unit for Cogeneration System
Abstract: This paper studies the feasibility of developing a compact system based on a photovoltaic panel with a heat exchanger embedded in a phase change material (PCM) attached to the rear side of the panel. The system generates electric energy at the PV panel, and thermal energy using the removed heat from the panel. The paper analyzes the improvement in PV panel efficiency and the Coefficient of Performance (COP) of the …
Published in Journal of Alternate Energy Sources & Technologies · Vol. 14, Issue 1, 2024 · pp. 13–24 Read article
-
Microstructural Investigation on Strength of New Age Mortar Synthesis with Thermosetting Polymer, GGBS, Fly Ash and Quarry Dust
Abstract: AbstractThermo setting polymer mortars containing Resin, hardener, fly ash, Quarry dust and GGBS (Ground Granulated Blast furnace slag). Merging representation of bio phenol-A-Di-glycidyl ether-based polymer with fly ash, Quarry dust and GGBS results are presented here for this present study. An innovative process is used to prepare the specimen in mild condition with commercial thermo setting polymer-based resin and hardener, fly ash, GGBS, along with quarry-dust-based paste. Following this procedure, …
Published in Journal of Polymer & Composites · Vol. 11, Issue 1, 2023 · pp. 63–71 Read article
-
Polymers for Sustainable Energy Generation: Advancing Green Building Technologies
Abstract: Implementing technologies for sustainable energy generation is essential to promote green building and minimize environmental effects. Owing to their diverse properties, polymers have gained immerging prominence in improving the efficiency and functionalities of various energy systems. Thermal energy storage Exploring the potential usage of polymers in energy generation for green buildings 1. The goals include assessing the performance and efficiency of polymer-based alternative technologies, while also investigating their environmental and …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 339–348 Read article
-
Corrugated Tube Shell-and-Tube Heat Exchanger Using Epoxy-Based Polymer Composite Coatings for Lightweight and Efficient Thermal Systems
Abstract: Corrugated tube geometries are widely recognized for their ability to enhance heat transfer through boundary layer disruption and secondary flow generation. In this study, a combined experimental and computational investigation is carried out to evaluate the thermo-hydraulic performance of a shell-and-tube heat exchanger incorporating corrugated stainless steel tubes integrated with an epoxy-based polymer composite coating and housed within a mild steel shell. Unlike conventional metallic systems, the present work introduces …
Published in Journal of Polymer & Composites · Vol. 14, Issue 2, 2026 · pp. 603–617 Read article
-
Design of SCADA and PLC Program for Raw Material Handling of TPS (Thermal Power Station)
Abstract: The power industry in India has now entered new era of large power generations and highly automatic control system. In today’s era the SCADA has played a very auspicious role in power generation industry because of its worldwide adaptability, extendibility, flexibility etc. The huge advancement in SCADA most of industries has jumped into automation field because of its big market. SCADA systems having both hardware and Software components. DMS offers …
Published in Journal of Thermal Engineering and Applications · Vol. 10, Issue 3, 2023 · pp. 46–50 Read article
-
Advancements In Al6061 Metal Matrix Composites: The Role of SiC, Al₂O₃, and Graphite Reinforcements in Enhancing Properties and Applications
Abstract: Al6061-based metal matrix composites (MMCs) reinforced with silicon carbide (SiC), graphite (Gr), and aluminum oxide (Al₂O₃) exhibit a unique combination of mechanical, thermal, and tribological properties, making them highly suitable for advanced engineering applications. SiC enhances hardness, wear resistance, and load-bearing capacity, while Al₂O₃ improves thermal stability and mechanical strength. Graphite provides self-lubricating properties, reduces friction, and lowers the composite's density, improving fatigue resistance. The synergy of combining these reinforcements …
Published in Journal of Polymer & Composites · Vol. 13, Issue 3, 2025 · pp. 90–98 Read article
-
Comparative Analysis of Pond Ash as a Partial Replacement of Sand as Subbase Material for Concrete Paver Block Hardstand sustaining storage of Bulk Cargo
Abstract: This work presents an industrial waste-derived subbase material that can take the place of conventional granular material for subbase in hardstand foundation construction. This industrial waste hugely deposited in the ash lagoons namely Pond Ash (PA) which is globally generated at an amount of 780 Metric Tons from thermal power plants annually ,as foundation material for hardstand construction, will not only help the cause of residual waste disposal problems but …
Published in Journal of Geotechnical Engineering · Vol. 12, Issue 3, 2025 · pp. 32–45 Read article
-
Reduction Of Total Electricity Generation Cost For Complicated Power Systems Considering Renewable Energy Sources By Using A Sea Horse Optimizer
Abstract: This paper focuses on solving the economic load dispatch (ELD) problem by incorporating the presence of wind and solar power plants alongside conventional thermal power plants (THs). Particle swarm optimization (PSO) and Sea horse optimizer (SHO) are applied to solve the problem with the main objective function of minimizing the total electricity generation cost (TEGC). SHO is a novel meta-heuristic method recently proposed, while PSO is one of the classical …
Published in Journal of Thermal Engineering and Applications · Vol. 9, Issue 3, 2022 · pp. 1–8 Read article
-
Thermal Management of Different Composites Materials Using a Convergent and Straight Vortex Tube
Abstract: The present study focuses on an in-depth and meticulous exploration into the intricate realm of thermal management in three distinct yet widely utilized composite materials—namely, Liquid Crystal Polymer (LCP) Composites, Glass Fiber Reinforced Polymers (GFRPs), and Aramid Fiber Composites (Kevlar). This investigation employs an innovative counter-flow vortex tube system, meticulously analyzing and comparing the thermal efficiency of these materials under different intake configurations. Specifically, two distinct geometrical intake designs—a straight …
Published in Journal of Polymer & Composites · Vol. 13, Issue 5, 2025 · pp. 252–266 Read article