Search
125 articles for “aluminum”
-
Comprehensive Review on Brake Friction Materials
Abstract: Automobile manufacturers are currently dedicated to enhancing vehicle speeds for the purpose of saving travel time. However, achieving this objective necessitates the use of friction materials capable of handling high-speed braking. In this article, we will delve into the historical evolution of materials utilized for brake pads and drums. In the past, asbestos stood out as the most widely employed brake lining material due to its effectiveness. Unfortunately, its carcinogenic …
Published in Journal of Polymer & Composites · Vol. 11, Issue 8, 2023 · pp. 197–214 Read article
-
Evaluation of Fly Ash/ZrO2 Reinforced AZ91E Hybrid Composites Based on Wear and Friction Characteristics
Abstract: In the current study the compo-casting Al alloy MMCs' wear resistance was examined under a variety of abrasive circumstances, including coefficient friction, wear rate and it’s sliding distance. The AZ91E matrix composite was made by the liquid metallurgy process and reinforced with aluminum plated zirconium dioxide (ZrO2) particles. Designers examined the characteristics of matrix alloys along with created composites. friction and wear from dry sliding experiments had been performed on …
Published in Journal of Polymer & Composites · Vol. 11, Issue 8, 2023 · pp. 324–338 Read article
-
A Comprehensive Review on Red mud as Construction Material and its Utilization for Environmental Advantage
Abstract: These materials can help to further decrease pollution and disposal difficulties when utilized effectively in civil engineering applications. Red mud, a byproduct of converting bauxite into aluminum, collects and occupies an increasing amount of deforested area because of its high alkalinity. With little chance of being used, an estimated redmud of 116 tons are created year globally, posing a major risk of contamination and pollution. However, because they will be …
Published in Journal of Construction Engineering, Technology & Management · Vol. 14, Issue 1, 2024 · pp. 35–40 Read article
-
An Experimental Investigation on Surface Roughness of Laser Beam Machining of Aluminium Alloy
Abstract: Laser beam machining (LBM) is a cutting-edge technique widely utilized for precision machining of advanced materials. This experimental investigation focuses on the surface roughness of aluminum alloy (Al 6061) during LBM. The study systematically examines the impact of process parameters such as laser power, cutting speed, and gas pressure on surface roughness (Ra). The significance of surface roughness in determining the quality and functionality of machined components is emphasized. The …
Published in Journal of Polymer & Composites · Vol. 12, Issue 6, 2024 · pp. 82–104 Read article
-
Super Ni 718 Machinability Investigation on Electrical Discharge Machining Using Hybrid Al 7(075+178) Electrode Under Abrasive Assisted Dielectric
Abstract: As aluminum alloy is the lightest metal and has the best mechanical qualities among metal, it has proven to be a perfect choice for strututal industry, particularly in the aerospace sector.7xxx alloys from the Al alloy family are widely used in aviation constructions due to their outstanding processing, welding efficiency, great specific strength & stiffness, and high toughness. The two aluminum alloys that are most frequently used in airplane structures …
Published in Journal of Polymer & Composites · Vol. 13, Issue 1, 2025 · pp. 1–17 Read article
-
Investigating the effect of Anodes workfunction on the Opto-electronics Performance of Organic Light Emitting Diode
Abstract: The research aims to assess the performance of organic light-emitting diodes (OLEDs) by exploring how various anode materials affect their optoelectronic properties. OLEDs are crucial for modern displays and lighting, and their efficiency and functionality are heavily influenced by the materials used in their design.This study examines four different anode materials: Indium Tin Oxide (ITO), Zinc Oxide (ZnO), Aluminum-doped Zinc Oxide (AZO), and Poly(3,4-ethylenedioxythiophene) Polystyrene Sulfonate (PEDOT: PSS). These materials …
Published in Research & Reviews : Journal of Physics · Vol. 13, Issue 2, 2024 · pp. 27–37 Read article
-
An Analysis of Machining Parameters for Metal Matrix Composite
Abstract: The electro-discharge machining analysis of hybrid Composite is presented in this work. Variables are chosen for the input process parameters. The material removal rate is acknowledged as an output parameter, together with the current, graphite and silicon carbide percentage and pulse on time. We used the Taguchi Method to conduct our experiments. To create the theoretical model and look into how process parameters affect the rate at which material is …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 76–85 Read article
-
Enhancing The Mechanical Performance of Al6061/Graphite Composites Reinforced with Sic and Aluminium Oxide Processed by Stir Casting
Abstract: The study investigates the mechanical properties of aluminum alloy Al6061 reinforced with varying proportions of silicon carbide (SiC) (0 wt%, 4 wt%, 5 wt%, and 6 wt%) and aluminum oxide (Al₂O₃) (0 wt%, 4 wt%, 3 wt%, and 2 wt%), with a constant addition of 1 wt% graphite. The composites were fabricated using the stir casting process, an efficient and economical method for uniformly distributing ceramic reinforcements within the metal …
Published in Journal of Polymer & Composites · Vol. 13, Issue 2, 2025 · pp. 66–74 Read article
-
Exploring the Influence of Machining Parameters on Geometric Form and Orientation Controls (23 Design)
Abstract: This work explores the influence of machining parameters using on geometric form controls flatness and straightness as well as orientation control parallelism using an aluminum 6061 workpiece. Due to its good strength, machinability and cost- effectiveness, aluminum 6061 is widely used. In this experimental work, full factorial design is used and each factor has two levels. The response parameters chosen include flatness, straightness, and parallelism, which govern the form and …
Published in Journal of Experimental & Applied Mechanics · Vol. 16, Issue 1, 2025 · pp. 10–16 Read article
-
A Review on Characterization of Mechanical Behavior of AA5083 Through Equal Channel Angular Pressing at Different Channel Angles
Abstract: Materials that have been enhanced through traditional techniques like strain hardening, the addition of solutes, altering grain size through precipitation and refining are commonly utilized in industrial applications. However, there is a restriction on the extent of deformation that these traditional techniques can impose on a material. This research centered on examining the primary mechanical characteristics of aluminum alloys when polycrystalline materials incorporate an extremely fine grain size. By producing …
Published in Journal of Polymer & Composites · Vol. 13, Issue 4, 2025 · pp. 54–68 Read article
-
Fabrication and Multi scale Characterization of Functionally Graded Composites Reinforced with Hybrid Ceramic–Metallic Phases
Abstract: Using composite materials as functionally graded composites (FGM) can improve its excellent material properties. In this work, magnesium peroxide, silicon carbide, and aluminum are used to create four-layer FGMs. The sintering process, which blends the particles of each material using a powder methodology, has been used to complete the fabrication process. Three factors, including sintering time, sintering temperature, and compacting pressure, are taken into account when fabricating FGM. The FGM …
Published in International Journal of Mechanical Dynamics and Systems Analysis · Vol. 3, Issue 2, 2025 · pp. 1–11 Read article
-
Study of pH Behaviour of Slurry on Surface Morphology of Copper Material with Single Pole Magnetic Abrasive Finishing Process
Abstract: The chemical oxidizers—sodium hydroxide, Marshall’s acid salt, and hydrogen peroxide—were effectively employed in the wet polishing of copper using the SPMAF experimental setup. The manuscript explores preparation of slurry used for polishing copper material using single pole magnetic abrasive finishing (SPMAF) framework. The slurry contains distilled water, 1200-grit aluminum oxide abrasives, sodium hydroxide (NaOH), potassium persulfate (K₂S₂O₈), and hydrogen peroxide (H₂O₂), combined in precise amount. Specifically, 100 ml of distilled …
Published in Journal of Polymer & Composites · Vol. 14, Issue 1, 2026 · pp. 1887–1896 Read article
-
Investigations of A Solar Dryer With Thermal Storage
Abstract: This study presents the design, building, and performance evaluation of a low-cost mixed-mode natural convection solar cabinet dryer in conjunction with a latent heat thermal energy storage system. The work's goal is to reduce post-harvest losses in rural and semi-urban areas by offering an effective and reasonably priced method of preserving agricultural goods. The dryer is made out of a transparent polycarbonate lid to allow for solar heat gain, an …
Published in Journal of Refrigeration, Air conditioning, Heating and ventilation · Vol. 13, Issue 1, 2026 Read article
-
Evaluation on the Mechanical Strength of TIG Welded 6061Aluminium Alloy Joints
Abstract: Aluminum alloy Al-6061 is extensively used in aerospace, automotive, and marine industries due to its excellent mechanical properties, lightweight nature, and corrosion resistance. However, welding this alloy presents challenges such as porosity, hot cracking, and strength reduction in the heat-affected zone (HAZ). Tungsten Inert Gas (TIG) welding, known for its precision and quality, is commonly employed for joining Al-6061. This study investigates the tensile strength of TIG-welded butt joints of …
Published in Trends in Machine design · Vol. 13, Issue 1, 2026 · pp. 34–39 Read article
-
Development and Comparative Study of Aluminium- Copper Metal Based Composite Through Different Routes
Abstract: The aim of this study is to develop aluminium-copper composite through powder metallurgy technique. Powder metallurgy is an art or technology which can produce exact dimension of final roducts utilizing less energy. Copper oxide (CuO) was used as the source of copper, which was extracted through a reduction process using dextrose. The reaction was thoroughly examined and reported. Commercially available aluminium powder served as source of the aluminium. Aluminium- copper …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 19–32 Read article
-
Eco-Efficient Skies: Life Cycle Assessment and Carbon Footprint Minimization of Fiber-Reinforced Polymer Composites in Aerospace Application
Abstract: The increasing integration of fiber-reinforced polymer (FRP) composites in aerospace structures necessitates a rigorous evaluation of their environmental sustainability throughout their entire life cycle. This study presents a comprehensive life cycle assessment (LCA) and carbon footprint analysis of carbon fiber-reinforced polymer (CFRP) and glass fiber-reinforced polymer (GFRP) composites applied to structural and semi-structural components in commercial aerospace applications. Following ISO 14040/14044 standards and employing the ReCiPe 2016 Midpoint (H) impact …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 147–160 Read article
-
Polymers and Composites in the Design and Construction of Unmanned Aerial Vehicles: A Comprehensive Technical Review
Abstract: The emergence of Unmanned Aerial Vehicles (UAVs) over the last few years has mostly been made possible by breakthroughs in material science. This review is concerned with an overview of some of the polymers and composites that are being commonly used in drone manufacturing in recent times, especially in relation to the influence of material choice on drone performance and capability. It sheds light on the drastic change in the …
Published in Journal of Polymer & Composites · Vol. 14, Issue 3, 2026 · pp. 874–882 Read article
-
Impact of Fracture in Geometrical, Material, and Load Rate Characteristics on J-Integral
Abstract: The present study investigates the influence of load rate, geometrical parameters, and material properties on the J-integral behavior of AA2050-T84 aluminum-lithium alloy using three-dimensional elastic–plastic fracture mechanics (EPFM) analysis. Finite element simulations were carried out using the ABAQUS software to evaluate crack driving forces in compact tension (C(T)) specimens under various mechanical and thermal conditions. The study focuses on the combined effects of strain rate, temperature-dependent strain hardening, specimen thickness …
Published in International Journal of Fracture Mechanics and Damage Science · Vol. 4, Issue 1, 2026 · pp. 38–45 Read article
-
Structural Performance Evaluation of Circular Perforated Plates under Mechanical Loading
Abstract: Circular perforated plates are structurally critical components in aerospace, automotive, and marine sectors, where perforation-induced stress concentrations govern failure under mechanical loading. This study conducts a systematic finite element analysis of stress distribution, deformation, and interlaminar behavior in aluminum and glass-epoxy laminates ([−45/45/90/0]S and [−45/45/90/0]AS) under uniform transverse pressure with clamped-free boundary conditions. Four perforation configurations—no hole, central hole, single-series, and 25-hole grid—were evaluated using ANSYS Shell-181, verified against Kirchhoff–Love, …
Published in Journal of Polymer & Composites · Vol. 14, Issue 4, 2026 · pp. 1–20 Read article
-
Comparative Analysis of Personal Rapid Transit System with Thermoplastic Material for Interconnecting Metro Station with Airport
Abstract: Personal rapid transit (PRT) systems open a slew of new possibilities for solving airport-related transportation issues, both on the ground and in the air. For use in airport applications, the advantages and disadvantages of this mode of transportation are contrasted. An implementation of the ULTra Personal Rapid Transit system to assist passenger and staff vehicle squares at Heathrow is used to showcase the work. The ULTra infrastructure's compact size and …
Published in Journal of Polymer & Composites · Vol. 11, Issue 1, 2023 · pp. 97–108 Read article